Panasonic-SAAKX73P-cs-sm 电路图 维修手册.pdf

《Panasonic-SAAKX73P-cs-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Panasonic-SAAKX73P-cs-sm 电路图 维修手册.pdf（138页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Panasonic Corporation 2012. All rights reserved. Unauthorized copying and distribution is a violation of law. PSG1206005CE A6 CD Stereo System Model No.SA-AKX73P Product Color: (K).Black Type TABLE OF CONTENTS PAGEPAGE 1 Safety Precautions- 3 1.1. General Guidelines- 3 1.2. Before Repair and Adjust

2、ment- 4 1.3. Protection Circuitry- 4 1.4. Caution For Fuse Replacement- 4 1.5. Safety Parts Information- 5 2 Warning- 6 2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatic Sensitive (ES) Devices - 6 2.2. Precaution of Laser Diode- 7 2.3. Service caution based on Legal restrictions- 8 2

3、.4. Handling Precautions for Traverse Unit- 9 3 Service Navigation-11 3.1. Service Information -11 4 Specifications -12 5 General/Introduction- 13 5.1. Media Information- 13 6 Location of Controls and Components- 14 6.1. Remote Control Key Button Operation - 14 6.2. Main Unit Key Button Operation- 1

4、5 7 Installation Instructions - 16 7.1. Speaker and A/C Connection- 16 8 Service Mode- 17 8.1. Cold-Start - 17 8.2. Doctor Mode Table- 18 8.3. Reliability Test Mode (CD Mechanism Unit (BRS11C) - 21 8.4. Self-Diagnostic Mode - 22 8.5. Self-Diagnostic Error Code Table- 22 8.6. Sales Demonstration Lock

5、 Function - 23 Please refer to the original service manual for: ? ? CD Mechanism Unit (BRS11C), Order No. PSG1201019AE ? ? Speaker system SB-AKX73P-K, Order No. PSG1206006AE RadioFans.CN 收音机爱 好者资料库 2 9 Troubleshooting Guide-24 9.1. Part Location -24 9.2. Troubleshooting Guide for F61 and/or F76-28 9

6、.3. D-Amp IC Operation X: NG (In case that time out happens.) : Either one of FOAOC, TR AOC and FO coarse AGC is NG. : If theAGC is NG (ignore others). 2.To cancel, press 0 on remote control . 2.To cancel, press 0 on remote control . ROM Version (Display 1) (Display 2) Year Develop Year Develop ROM

7、Type Version(Decimal) after 2 sec Version (Decimal )Checksum (Hex) 21 8.3.Reliability Test Mode (CD Mechanism Unit (BRS11C) Below is the process flow chart of the aging test for the CD Mechanism Unit (BRS11C). Fig. 1. Reliability Test (Loading) Fig. 2. Reliability Test (Traverse) Fig. 3. Reliability

8、 Test (Combination) OPEN Operation OPEN wait for 1 s CLOSE Operation CLOSE wait for 4 s Count up First Track Access First Track Play 5 s Last Track Access Last Track Play 5 s Count up First Track Access Access Play 10 s Open Operation Open wait for 1 s CLOSE Operation Count up First Track Last Track

9、 Last Track Play 10 s 22 8.4.Self-Diagnostic Mode 8.5.Self-Diagnostic Error Code Table Self-Diagnostic Function (Refer Section 8.4. Self-Diagnostic Mode) provides information on any problems occurring for the unit and its respective components by displaying the error codes. These error code such as

10、U*, H* and F* are stored in memory and held unless it is cleared. The error code is automatically display after entering into self-diagnostic mode. 8.5.1.Power Supply Error Code Table FL Display Key Operation Front Key Item Description Mode Name To enter into self diagnostic checking System will per

11、form a check on any unusual/error code from the memory To clear the stored in memory (EEPROM IC) Self Diagnostic Mode Error code information Delete error code Step 1: Select CD mode (Ensure no disc is inserted). Step 2: Press & hold follow by / on main unit for 2 seconds. Step 1: In self diagnostic

12、mode, Press on main unit. To exit, press /I on main unit or remote control. Step 1: In self diagnostic mode, Press 0 on remote control. To exit, press /I on main unit or remote control. Example: 23 8.5.2.CD Mechanism Error Code Table (CD Mechanism Unit (BRS11C) 8.6.Sales Demonstration Lock Function

13、8.6.1.Entering into sales Demo Mode Here is the procedures to enter into Sales Demonstration Lock. Step 1: Turn on the unit. Step 2: Select to any mode function. Step 3: Press OPEN/CLOSE key then / key at the same time,press and hold both OPEN/CLOSE and / keys for 5 sec. Step 4: The display will sho

14、w upon entering into this mode for 2 sec. Note: OPEN/CLOSE button is invalid and the main unit displays “LOCKED” while the lock function mode is entered. 8.6.2.Cancellation Step 1: Turn on the unit. Step 2: Select to any mode function. Step 3: Press OPEN/CLOSE key then / key at the same time,press a

15、nd hold both OPEN/CLOSE and / keys for 5 sec. Step 4: The display will show upon entering into this mode for 2 sec. Error CodeDiagnostic ContentsDescription of errorAutomatic FL DisplayRemarks CD H15CD Open AbnormalDuring operation POS_SW_R On fail to be detected with 4 sec. Error No. shall be clear

16、 by force or during cold start. Press on main unit for next error. CD H16CD Closing AbnormalDuring operation POS_SW_CEN On fail to be detected with 4 sec. Error No. shall be clear by force or during cold start. Press on main unit for next error. F26Communication between CD servo LSI and micro-p abno

17、rmal. During switch to CD func- tion, if SENSE = “L” within failsafe time of 20ms. Press on main unit for next error. 24 9Troubleshooting Guide 9.1.Part Location 9.1.1.SMPS P.C.B. Fig. 1 SMPS P.C.B. Thermistor : TH5861 Photocoupler : PC5720 AC Inlet : P5701 Fuse : F1 Photocoupler : PC5702, PC5799 Sw

18、itching Regulator IC: IC5701 SMPS Control IC: IC5799 Main Transformer : T5701 Rectifier Diode : D5801, D5802 Connector: CN5802 Sub Transformer : T5751 Sub Transformer : D5798 25 9.1.2.Main P.C.B. (Front Side) Fig. 2 Main P.C.B. (Front Side) 26 Fig. 3 Main P.C.B. (Back Side) Audio Digital Amp IC IC58

19、00 Voltage Regulator IC IC2010 Resistor Defective R5803 Resistor Defective R5805 Audio Digital Amp IC IC5700 Regulator Circuit Q2022 D2004 Regulator Circuit L2000 L2001 Regulator Circuit Voltage Regulator IC IC2011 Resistor Defective R5802 Resistor Defective R5704 Resistor Defective R5705 Resistor D

20、efective R5702 Resistor Defective R5703 Resistor Defective R5804 27 9.1.3.D-AMP P.C.B. Fig. 4 D-Amp P.C.B. Audio Digital Amp IC: IC5900 Resistor Defective R5905 Resistor Defective R5917 Resistor Defective R5922 Resistor Defective R5921 28 9.2.Troubleshooting Guide for F61 and/or F76 This section ill

21、ustrates the checking procedures when upon detecting the error of “F61” and/or “F76” after power up of the unit. It is for purpose of troubleshooting and checking in SMPS, Main & D-Amp P.C.B. 5Switching Regulator 5IC5701 Faulty . 6 T5751 Faulty. Switching Mode Power Supply Control IC (IC5799) faulty

22、. Set can ON1Speaker Output1Faulty speaker unit, Loose connection, Short. then F61 2D-AMP circuit D-AMP IC, IC5700, IC5800, IC5900 defective. (Check DC voltage at speaker terminals, 3V and above defective) DC Voltage ok but no sound, check DC Voltage at Pin 1 . 2a, 2b ok but no sound, check PWM wave

23、form at Pin 10 and Pin 14 . If no PWM, 12 resistors defective. Set can ON 1Main Transformer T5701Short circuit between Pin 11 and Pin 12 . then F76 1b Short circuit between Pin 13 and Pin 14 . 1c Short circuit between Pin 16 and Pin 17 . 2 2 Regulator Circuits 2a 2b 2c 3 Q2022 faulty (No +5V output)

24、. 2d IC2014 faulty (No +3.3V output). 2e IC2011 faulty (No +5V output). 2fL2001 Open. 3Photocoupler PC5720 solder crack, PC5720 Dry joint, short circuit, open circuit. 1Rectifier Diode D5801Improper contact between D5801 to Heatsink. Rectifier Diode D5802 TH5861 Improper contact between D5802 to Hea

25、tsink. Thermistor TH5860,1b Set trigger temperature protection. Set can ON working normally for some time then F76 SymptomRemarks Set cannot ON1AC Cord1AC Cord Faulty, Loose connection. 2 3Fuse, F13Fuse, F1 Open. 4Photocoupler4PC5702/PC5799 solder crack. PC5702, PC5799Dry joint, short circuit, open

26、circuit. IC2010 faulty (No +9V output). L2000 Open. Possible Fault(s)Checking Items AC Inlet, P5701P5701 solder crack, dry joint. IC, IC5701 Main Transformer T5751 2 1a Refer to Section 9.1.1 Fig. 1. SMPS P.C.B. Refer to Section 9.1.2 Fig. 2. and Fig.3. Main P.C.B. Refer to Section 9.1.1 Fig. 1. SMP

27、S P.C.B. Refer to Section 9.1.1 Fig. 1. SMPS P.C.B. Refer to Section 9.1.2 Fig. 3. Main P.C.B. and Section 9.1.3 Fig. 4. D-Amp P.C.B. Refer to Section 9.1.1 Fig. 1. SMPS P.C.B. 2b 2a 5V ok condition, 2.5V or 0V defective. 2c 1a 6a 6b D5798 faulty.6c For IC5800 (R5802, R5803, R5804, R5805). For IC570

28、0 (R5702, R5703, R5704, R5705). For IC5900 (R5905, R5917, R5921, R5922). 29 9.3.D-Amp IC Operation & Control 30 1170 1250 H 350 1260 1450 L 301 1460 1540 H 350 1550 1710 L 301 Table 4: F_HOP Control during 10 kHz Step Note: During activating, the 3 control pins namely MUTE_F, MUTE_A and MODE_DA must

29、 be used to cover the “Pop” sound cause by F-HOP switching. 31 10 Service Fixture & Tools Prepare service tools before process service position. Ref. NoService ToolsRemarks SFT1Main P.C.B. (CN2007) - SMPS P.C.B. (CN5802)REX1527(15P Cable Wire) 32 11 Disassembly and Assembly Instructions Caution Note

30、: This section describes the disassembly and/or assembly procedures for all major printed circuit boards & main compo- nents for the unit. (You may refer to the section of “Main components and P.C.B Locations” as described in the service manual) Before carrying out the disassembly process, please en

31、sure all the safety precautions & procedures are followed. During the disassembly and/or assembly process, please handle with care as there may be chassis components with sharp edges. Avoid touching heatsinks due to its high temperature after prolong use. (See caution as described below) During disa

32、ssembly and assembly, please ensure proper service tools, equipments or jigs is being used. During replacement of component parts, please refer to the section of “Replacement Parts List” as described in the ser- vice manual. Select items from the following indexes when disassembly or replacement are

33、 required. Disassembly of Top Cabinet Disassembly of Front Panel Unit Disassembly of Mic P.C.B. Disassembly of Panel P.C.B. Disassembly of Memory LED P.C.B. Disassembly of Remote Sensor P.C.B. Disassembly of USB P.C.B. Disassembly of Music Port P.C.B. Disassembly of Top Bar LED P.C.B. Disassembly of

34、 Bottom Bar LED P.C.B. Disassembly of Main P.C.B. Replacement of Voltage Regulator (IC2010) Replacement of Voltage Regulator (IC2011) Replacement of Audio Digital Amp IC (IC5800) Replacement of Audio Digital Amp IC (IC5700) Disassembly of D-Amp P.C.B. Replacement of Audio Digital Amp (IC5900) Disass

35、embly of SMPS P.C.B. Replacement of Switching Regulator IC (IC5701) Replacement of Rectifier Diode (D5702) Replacement of Rectifier Diode (D5801) Replacement of Rectifier Diode (D5802) Replacement of Rectifier Diode (D5803) Disassembly of CD Mechanism Unit (BRS11C) Disassembly of CD Interface P.C.B.

36、 Disassembly of CD Servo P.C.B. Disassembly of Rear Panel 33 11.1.Disassembly Flow Chart 11.3. Top Cabinet 11.4. Front Panel Unit 11.5. Mic P.C.B. 11.6. Panel P.C.B. 11.8. Remote Sensor P.C.B. 11.9. USB P.C.B. 11.10. Music Port P.C.B. 11.12. Bottom Bar LED P.C.B. 11.13. Main P.C.B. 11.20. SMPS P.C.B

37、. 11.18. D-Amp P.C.B. 11.14. Voltage Regulator IC (IC2010) 11.21. Switching Regulator IC (IC5701) 11.22. Rectifier Diode (D5702) 11.23. Rectifier Diode (D5801) 11.24. Rectifier Diode (D5802) 11.25. Rectifier Diode (D5803) 11.26. CD Mechanism Unit (BRS11C) 11.27. CD Interface P.C.B. 11.28. CD Servo P

38、.C.B. 11.29. Rear Panel 11.15. Voltage Regulator IC (IC2011) 11.16. Audio Digital Amp IC (IC5800) 11.19. Audio Digital Amp IC (IC5900) 11.17. Audio Digital Amp IC (IC5700) 11.7. Memory LED P.C.B. 11.11. Top Bar LED P.C.B. 34 11.2.Main Components and P.C.B. Locations 35 11.3.Disassembly of Top Cabine

39、t Step 1 Remove 2 screws on each side. Step 2 Remove 5 screws. Step 3 Slightly pull both side of Top Cabinet outwards as arrow shown. Step 4 Slightly lift up both side of Top Cabinet in an outward direction as shown. Step 5 Remove the Top Cabinet. Caution: During assembling, ensure that the catches

40、of the Top Cabinet catches are properly located & inserted into the Front Panel Unit as shown. 36 11.4.Disassembly of Front Panel Unit Refer to “Disassembly of Top Cabinet”. Step 1 Detach 27P FFC at the connector (CN2003) on Main P.C.B. Step 2 Detach 5P Cable Wire at the connector (CN2700) on Main P

41、.C.B. Step 3 Remove 1 screw at the SMPS Inner Chassis Unit. Step 4 Push inwards slightly at the Bottom Chassis as arrow shown and release tab at left side of the Front Panel Unit. Step 5 Release tabs at the bottom of the unit. 37 Step 6 Push inwards slightly at the Bottom Chassis and release tab at

42、right side of the Front Panel Unit. Step 7 Remove the Front Panel Unit 11.5.Disassembly of Mic P.C.B. Refer to “Disassembly of Top Cabinet”. Refer to “Disassembly of Front Panel Unit”. Step 1 Remove the Mic knob. Step 2 Remove 1 screw at the Mic P.C.B. Step 3 Desolder 4P Cable Wire at the connector

43、(ZJ6500) on the Mic P.C.B. Step 4 Desolder 2P Cable Wire at the connector (ZJ6501) on the Mic P.C.B. Step 5 Release 1 catch. Step 6 Remove the Mic P.C.B. 38 11.6.Disassembly of Panel P.C.B. Refer to “Disassembly of Top Cabinet”. Refer to “Disassembly of Front Panel Unit”. Refer to “Disassembly of Mi

44、c P.C.B.”. Step 1 Remove the Volume Knob. Step 2 Remove the Skip Knob. Step 3 Remove 6 screws. Step 4 Detach 2P Cable Wire at the connector (CN6006) on the Panel P.C.B. Step 5 Detach 2P Cable Wire at the connector (CN6004) on the Panel P.C.B. Step 6 Release catches by following the sequences (1-10).

45、 Step 7 Lift up to remove the Panel P.C.B. Step 8 Desolder 4P Cable Wire at the connector (ZJ6002) on the Panel P.C.B. 39 Caution: During assembling, ensure that the Panel P.C.B. is seated properly through the guides & fully catched. 11.7.Disassembly of Memory LED P.C.B. Refer to “Disassembly of Top

46、 Cabinet”. Refer to “Disassembly of Front Panel Unit”. Refer to “Disassembly of Mic P.C.B.”. Refer to “Disassembly of Panel P.C.B.”. Step 1 Release 2 catches. 11.8.Disassembly of Remote Sensor P.C.B. Refer to “Disassembly of Top Cabinet”. Refer to “Disassembly of Front Panel Unit”. Refer to “Disassembly of Mic P.C.B.”