Jvc-HRXV-11-E-Service-Manual 电路图 维修手册.pdf

《Jvc-HRXV-11-E-Service-Manual 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Jvc-HRXV-11-E-Service-Manual 电路图 维修手册.pdf（116页珍藏版）》请在收音机爱好者资料库上搜索。

1、COPYRIGHT 2003 VICTOR COMPANY OF JAPAN, LTD SERVICE MANUAL General Power requirementsAC 200-240V, 50/60 Hz Power consumptionOperation mode : 23W Standby mode : 6.7W Dimensions (approx.)430 X 97.5 X 293 mm (w/h/d) Mass (approx.8 kg Operating temperaturC to 35 C (41 F to 95 F) Operating humidity5 % to

2、 90 % Timer24 hours display tape Program capacity 1 month 7 program RF ModulatorUHF 22-68 (Adjustable) System Laser Semiconductor laser, wavelength 650 nm Video Head systemDouble azimuth 4 heads, helical scanning. Signal systemPAL Frequency responseDVD (PCM 96 kHz): 8 Hz to 44 kHz DVD (PCM 48 kHz):

3、8 Hz to 22 kHz CD: 8 Hz to 20 kHz Signal-to-noise ratioMore than 100dB (ANALOG OUT connectors only) Harmonic distortionLess than 0.008% Dynamic rangeMore than 100 dB (DVD) More than 95 dB (CD) Inputs (VCR) Audi6.0dBm, more than 10 kohms (SCART) -6.0dBm, more than 47 kohms (RCA) Video1.0 Vp-p, 75 ohm

4、s, unbalanced (SCART/RCA) Outputs (DVD) S-VIDEO OUT(Y) 1.0 Vp-p 75 ohms, negative sync., Mini Din 4-pin x 1 (C) 0.3 Vp-p 75 ohms COMPONENT VIDEO OUT(Y) 1.0 V (p-p), 75 , negative sync, RCA jack x 1 (Pb)/(Pr) 0.7 V (p-p), 75 , RCA jack x 2 Audio output (digital audio)0 5 V (p-p), 75 , RCA jack x 1 Au

5、dio output (optical audio)5 V (p-p), 75 , Optical connector x 1 Audio output (analog audio)2 0 Vrms (1 kHz, 0 dB), 330 , RCA jack (L, R) x 2/SCART(TO TV) Outputs (VCR) Audi6 0dBm, less than 1 kohms (SCART) Video1 0Vp-p, 75 ohms, unbalanced (SCART) Design and specifications are subject to change with

6、out notice. )4 o- o- e5 Manufactured under license from Dolby Laboratories. “ Dolby” and double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories, Inc. All rights reserved. Manufactured under license from Digital Theater Systems, Inc. US Pat.

7、 No. 5,451,942 and other world-wide patents issued and pending. “ DTS” and “ DTS Digital Out” are trademarks of Digital Theater Systems, Inc. Copyright 1996 Digital Theater Systems, Inc. All rights reserved. No.82984 2003/06 HR-XV2EX, HR-XV2EY, HR-XV2EL, HR-XV11EX HR-XV2EX,HR-XV2EY,HR-XV2EL,HR-XV11E

8、X D2VP11 DVD PLAYER /VIDEO CASSETTE RECORDER SPECIFICATIONS (The specifications shown pertain specifically to the model HR-XV2E.) PAL R VV W DVD M NUME OR S B IEA G E SEA CH S VD O u + VV VC V VCR R + V VCR V 2 4 79 ND M SY K A RadioFans.CN 收音机爱 好者资料库 CONTENTS SECTION 1 . . . . SUMMARY SECTION 3 . .

9、 . . ELECTRICAL SECTION 4 . . . . MECHANISM OF VCR PART SECTION 5 . . . . MECHANISM OF DVD PART SECTION 6 . . . . REPLACEMENT PARTS LIST RadioFans.CN 收音机爱 好者资料库 SECTION 1 SUMMARY CONTENTS Important Safety Precautions SPECIFICATIONS . 1-5 RadioFans.CN 收音机爱 好者资料库 Important Safety Precautions Prior to

10、shipment from the factory, JVC products are strictly inspected to conform with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is

11、 being serviced. Fig.1 1.Locations requiring special caution are denoted by labels and inscriptions on the cabinet, chassis and certain parts of the product. When performing service, be sure to read and com- ply with these and other cautionary notices appearing in the operation and service manuals.

12、2.Parts identified by the symbol and shaded ( ) parts are critical for safety. Replace only with specified part numbers. Note: Parts in this category also include those specified to com- ply with X-ray emission standards for products using cathode ray tubes and those specified for compliance with va

13、rious regulations regarding spurious radiation emission. 3.Fuse replacement caution notice. Caution for continued protection against fire hazard. Replace only with same type and rated fuse(s) as specified. 4.Use specified internal wiring. Note especially: 1) Wires covered with PVC tubing 2) Double i

14、nsulated wires 3) High voltage leads 5.Use specified insulating materials for hazardous live parts. Note especially: 1) Insulation Tape3) Spacers5) Barrier 2) PVC tubing4) Insulation sheets for transistors 6.When replacing AC primary side components (transformers, power cords, noise blocking capacit

15、ors, etc.) wrap ends of wires securely about the terminals before soldering. Power cord Fig.2 10. Also check areas surrounding repaired locations. 11. Products using cathode ray tubes (CRTs) In regard to such products, the cathode ray tubes themselves, the high voltage circuits, and related circuits

16、 are specified for compliance with recognized codes pertaining to X-ray emission. Consequently, when servicing these products, replace the cath- ode ray tubes and other parts with only the specified parts. Under no circumstances attempt to modify these circuits. Unauthorized modification can increas

17、e the high voltage value and cause X-ray emission from the cathode ray tube. 12. Crimp type wire connector In such cases as when replacing the power transformer in sets where the connections between the power cord and power transformer primary lead wires are performed using crimp type connectors, if

18、 replacing the connectors is unavoidable, in or- der to prevent safety hazards, perform carefully and precisely according to the following steps. 1) Connector part number : E03830-001 2) Required tool : Connector crimping tool of the proper type which will not damage insulated parts. 3) Replacement

19、procedure (1) Remove the old connector by cutting the wires at a point close to the connector. Important : Do not reuse a connector (discard it). Fig.7 cut close to connector Fig.3 (2) Strip about 15 mm of the insulation from the ends of the wires. If the wires are stranded, twist the strands to avo

20、id frayed conductors. 15 mm Fig.4 (3) Align the lengths of the wires to be connected. Insert the wires fully into the connector. Connector Metal sleeve Fig.5 (4) As shown in Fig.6, use the crimping tool to crimp the metal sleeve at the center position. Be sure to crimp fully to the complete closure

21、of the tool. 1 vPrecautions during Servicing 7.Observe that wires do not contact heat producing parts (heatsinks, oxide metal film resistors, fusible resistors, etc.) 8.Check that replaced wires do not contact sharp edged or pointed parts. 9.When a power cord has been replaced, check that 10-15 kg o

22、f force in any direction will not loosen it. 1.25 2.0 5.5 Crimping tool Fig.6 (5) Check the four points noted in Fig.7. Not easily pulled free Crimped at approx. center of metal sleeve Conductors extended Wire insulation recessed more than 4 mm S40888-01 vSafety Check after Servicing Examine the are

23、a surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions, Afterwards, perform the following tests and confirm the specified values in order to verify compli- ance with safety standards. 1.Insulation resistance test

24、 Confirm the specified insulation resistance or greater between power cord plug prongs and externally exposed parts of the set (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.). See table 1 below. 2.Dielectric strength test Confirm

25、specified dielectric strength or greater between power cord plug prongs and exposed accessible parts of the set (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.). See table 1 below. 3.Clearance distance When replacing primary circui

26、t components, confirm specified clearance distance (d), (d) be- tween soldered terminals, and between terminals and surrounding metallic parts. See table 1 below. 4.Leakage current test Confirm specified or lower leakage current between earth ground/power cord plug prongs and externally exposed acce

27、ssible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.). Measuring Method : (Power ON) Insert load Z between earth ground/power cord plug prongs and externally exposed accessi- ble parts. Use an AC voltmeter to measure across

28、 both terminals of load Z. See figure 9 and following table 2. 5.Grounding (Class 1 model only) Confirm specified or lower grounding impedance between earth pin in AC inlet and externally exposed accessible parts (Video in, Video out, Audio in, Audio out or Fixing screw etc.). Measuring Method: Conn

29、ect milli ohm meter between earth pin in AC inlet and exposed accessible parts. See figure 10 and grounding specifications. d d Chassis Power cord, primary wire Region USA SCOR,SQCK,SQSO XLAT , E_STI , E_ENB , E_DR RF XLAT , LDON IC401 CS4391 XIO1,XIO ,XIO10 /SRST F_CLK F_OUT PCMCLK ALE MSDATO MDP1

30、FOK DEFECT DSP_ SENSE LOCK E_SOUT ZISENB /XRST DAC_RST 16 9 , PAL_SW , AUTO_SW , MIC_ON Y_SEL /A_MUTE /DAC_CS1 /DAC_CS2 V_MUTE DAC_CLK DAC_OUT ADCCLK ACT MUTE , LOAD OPEN , LOAD CLOSE MIRR AD 04 21 PSENB FLD /FLD_CS FLD_CLK FLD_OUT EE CS , EE CLK , EE OUT F IN IC3F1 FLASH ROM /FLASH_CS , /RD PWEO LA

31、0 LA1 LA2 LA3 LADD 04 19 MD00 31 MCLK2 CKE MA00 10 MA12,13 /CS0 /RAS /CAS /WE DQM03 REQP SDCLKI , PSYNC DVD1 7 DSP INT SENSE /DSP CS F_IN DA_AIN SPDIF ACLK LRCK AOUT03 AMP L/R L/R 5 3VA POWER 8VA 12V 3 3V 2.5V A.GND, D.GND, M.GND 5V AD0 7 LADD45 , LA03 AD 00 15 MDP,FDO,TDO,FMO,MON OPEN_SW CLOSE_SW L

32、IMIT_SW CPLD 27MHz X-TAL 33.8688MHz X-TAL IC206 INVER TER NS 3-61 IC2A1 HD153702TF RF Signal Processdr IC201 HDC25D811B CD/DVD DSP DVD SERVO IC203 SDRAM 16M IC2M1 FAN8004 SpindleMotor,LoadingMotor, Actuator Driver PICK UP DVD:A,B,C,D, SENS,FOK, MSDATO,DEFECT,DSP_SENSE SQSO,SQCK,SCOR XLAT,S_CLK,S_DAT

33、A DSP_CS,/WR,/RD DO0:7 AO0:5 DVD_DATA0:7 MCK UCOM I/F MPEG I/F UCOM I/F M/D DVD/CD RF FE, TE, PI MIRR,TZC ICADDR0:8 ICDATA00:15 MON,MDP FDO,TDO,FMO Spindle focus,tracking,loading,sled Load open/close(loading control) CD:A,B,C,D/E,F 4 4 5 3 3 3 8 6 8 8 2 4 9 16 NS 2. RF/CD DSP/DVD DSP/DVD SERVO BLOCK

34、 DIAGRAM 3-62 3. AUDIO BLOCK DIAGRAM IC401 CS4932 Audio DAC IC402 LPF & Buffer KA 5532 OP AMP L R U-COM I/F DA_DATA0 DAC_RST S_DATA S_CLK DAC_L0 DA_LRCK DA_BCK DA_XCK L R TO VCR MPEG I/F NS 3-63 4. MPEG BLOCK DIAGRAM IC501 PANTERA-2 LE/PLUS IC301 HC353106 IC305 SDRAM 16/32BIT 64M IC502 93C46 EEPROM

35、IC3F1 FLASH MEMORY AD0 78 DSP I/F DVD0 7 8 LA0 3 4 SCLK,SDATA SQCK,SQS0 REQP SDCLK1,PSYNC DSP_ INT SENSE /DSP_ CS AD 04 21 RF & MOTOR I/F MIRR LDON SCLK,SDATA EE_CS F_IN 32 MD00 31 MCLK2 CKE MA0010 MA12,13 /CS0 /RAS/ /CAS /WE /DQM0 3 SPINDLE_ FG ALE AD04 19 16 LADD04 19 16 LA0 3 4 AD00 15 16 AUDIO D

36、A_DATA0 3 DA_BCK,DA_LRCK,DA_XCK 4 DAC_L0,DAC_L1 DAC_RST TO VCR C/R(B) CVBS/G(R) Y/B(G) CVBS V_MUTE,16 9 ZISENB /RD /PWED IC301 NS 02. 12. 04 R17147A COMBI NS 5 TRACKING LOOP FOCUS LOOP SLED LOOP SPINDLE LOOP WAVEFORM 16M SDRAM 10/16V 22 DSP II TO/FROM MPEG 3-643-65 CIRCUIT DIAGRAMS 1. DVD DSP CIRCUI

37、T DIAGRAM 5 4 3 2 4 1 4 02. 12. 04 R17145A COMBI NS TRACKING LOOP FOCUS LOOP SLED LOOP SPINDLE LOOP WAVEFORM Q2A5, Q2A6 TO/FROM MEMORY TO/FROM MEMORY TO/FROM DSP TO/FROM DSP TO/FROM MPEG TO/FROM MEMORY TO/FROM DSP TO/FROM DSP 3-663-67 2. DRIVE & RF CIRCUIT DIAGRAM Tray not open/close Digitron all no

38、t display system not working Tray not open/close Digitron all not display system not working Digitron all not display system not working 02. 12. 04 R17148A COMBI NS Digitron all not display system not workry DRIVE & RF 3-683-69 3. MEMORY CIRCUIT DIAGRAM 02. 12. 04 R17150A COMBI NS PDV01-PPD01 PDV02-

39、PMD01 PDV03-PMD02 (TO/FROM VCR JACK) (TO/FROM VCR SYSTEM) (TO/FROM VCR POWER) TO/FROM MPEG TO/FROM MPEG TO/FROM JACK TO/FROM MEMORY 3-703-71 4. INTERFACE CIRCUIT DIAGRAM Optical/Coaxial out CVBS Y/Pb/Pr(Componet) Y/C(S-VHS) WAVEFORM 02. 12. 04 R17146A COMBI NS HB-1S1608 MM74HCT244 3-723-73 5. -COM/E

40、XPANDER CIRCUIT DIAGRAM 02. 12. 04 R17149A COMBI NS DAP202K 3-743-75 6. JACK CIRCUIT DIAGRAM 3-763-77 WAVEFORMS IC2A1 TP2A0 IC2A1 Pin 36 Tracking Error IC501 Pin 114 Component Y IC2A1 Pin 36 VBR TRACKING Error IC2A1 Pin 39, Focus Error IC2A1 Pin 38, PE IC2A1 Pin 39, Focus Error(in Focus Search) IC20

41、1 Pin 48, Focus Drive(FDO) IC501 Pin 118, CompositeIC501 Pin 112, Chrominance (Super video out Mode) ek Stop : 2 50MS/s4 Acqs M20 0s 2 Apr 1999 14:47:27 GlitchCh1 Ch3500mV 3 IC501 Pin 114, Luminance (Super video out Mode) ek Stop : 1 00kS/s3290 Acqs M 500sCH1 280/mV Edge Slope ype Source Ch1 Couplin

42、g DC Level 280mV Mode & Holdoff 3 Ch31 00V T Slope IC501 Pin 98, MPEG Clock(27MHz) IC501 Pin 112 Component Pb IC501 Pin 110 Component Pr 3-783-79 CIRCUIT VOLTAGE CHART I C 2 A 2 I C 2 A 4 I C 2 M 1 STOPPLAY MODE PIN NO. 3.21 3.21 3.21 3.21 3.21 3.21 3.21 3.21 0.00 3.21 3.21 3.21 3.21 3.21 3.21 3.21

43、3.21 3.21 3.21 3.21 3.21 0.01 0.01 3.21 3.21 0.02 0.02 0.02 0.02 0.02 0.02 0.02 3.21 3.21 3.21 0.02 1.80 0.02 0.02 0.02 1.78 0.02 0.13 1.78 0.02 0.02 0.02 1.78 3.21 0.01 0.01 0.01 0.02 3.07 3.05 3.07 3.02 3.05 3.04 3.05 3.05 3.05 0.00 3.04 0.00 0.00 0.00 3.03 3.05 3.04 0.00 0.00 0.00 0.00 0.00 0.03

44、0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 3.19 0.00 0.00 0.00 0.00 0.00 0.00 1.61 0.20 1.61 2.70 2.70 2.70 1.81 3.20 0.00 1.57 1.53 0.00 EEPLAY MODE PIN NO. 5.72 0.02 3.21 0.02 1.80 2.38 0.02 3.21 3.21 3.21 0.02 0.02 0.87 0.01 3.21 1.07 3.21 0.02 3.21 0.02 0.02 0.87 1.59 0.87 0.87 2.36

45、2.86 3.24 3.24 2.19 2.39 0.00 0.00 2.19 2.38 2.18 1.80 0.92 2.69 1.77 1.81 1.53 1.83 1.81 0.00 0.00 1.81 3.21 3.21 2.28 2.28 0.90 1.30 1.59 2.00 5.18 0.00 3.21 0.00 1.59 0.00 0.00 3.01 0.00 3.21 0.00 0.00 1.19 1.90 3.21 1.55 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.78 2.15 0.00 0.00 0.00 1.97 0.00

46、0.00 0.00 0.00 0.00 0.00 1.62 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 1.63 3.24 3.25 0.00 0.00 1.48 1.67 1.59 1.65 EEPLAY MODE PIN NO. 2.00 2.40 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 3.21 0.70 3.21 3.21 0.02 3.21 3.21 3.00 0.02 3.21 3.21 3.21 0.84 0.02 3.21 3.21 2.67 1.85 2.40 2.68 2.64

47、2.64 3.21 1.12 0.02 0.02 2.66 2.67 2.68 2.68 1.09 1.09 0.02 0.02 0.67 0.90 3.21 3.21 0.02 0.00 0.00 3.02 3.21 3.21 1.64 1.60 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 3.22 3.22 3.22 1.61 0.00 1.64 1.61 0.00 0.00 2.35 3.25 1.59 0.02 0.00 3.22 2.35 2.39 1.62 2.12 2.41 0.30 3.20 3.22 2.32 0.00 0.00

48、0.30 0.30 0.30 0.30 2.33 0.00 3.22 0.00 1.53 0.00 3.22 3.22 0.00 0.00 0.00 2.70 3.24 3.24 EEPLAY MODE PIN NO. 2.31 2.38 2.39 1.80 3.08 0.02 0.04 3.03 3.21 3.21 3.21 3.21 0.02 3.21 3.21 3.21 0.02 0.02 0.02 0.02 0.02 0.02 3.21 1.50 3.21 1.55 1.57 1.63 0.23 2.32 2.20 1.63 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 0.02 3.21 0.0