Alesis-Microverb-sp-sch 电路图 维修手册.pdf

《Alesis-Microverb-sp-sch 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Alesis-Microverb-sp-sch 电路图 维修手册.pdf（10页珍藏版）》请在收音机爱好者资料库上搜索。

1、10-22-02 Microverb (C4) General Description The Alesis MicroVerb IV is the latest in the line of popular effects processors of the micro series. Similar in performance to the MicroVerb, the NanoVerb is a scaled down version. Combining the well known power of Alesis custom processing with small size

2、and affordability, the MicroVerb IV (Product Code C4) and NanoVerb (Product Code NV) are based largely on the design of the MidiVerb IV. The MidiVerb IV custom chip set, along with the latest ADC and DAC technology help make the C4 and NV two of the most powerful signal processors in their price ran

3、ges. Particularly in the NV the use of surface mount technology helps push the envelope of size and weight verses performance. Reference designators for the C4 are taken from the Rev. C schematic. Reference designators for the NV are taken from the Rev. B schematic and are denoted by brackets when c

4、omponents are functionally similar to the C4. Note that for both of these units there are several different main PCB revisions. There are no functional differences between these revisions. However, it should be noted that older PCB revisions will have some wire jumpers that later rev.s incorporated

5、into the PCBs. Figure 1 shows the simplified block diagram of the C4. As the NanoVerb is even simpler, there is no need to simplify it beyond the schematic. Figure 1 C4 Service Manual V1.01 RadioFans.CN 收音机爱 好者资料库 10-22-02 Test Procedures C4 Self Test The MicroVerb 4 has two self test modes which al

6、low the user to run diagnostic tests. In Individual Test mode, the user can select particular tests to run. In All Test mode, the MicroVerb 4 runs all of the tests in series. - Power up the unit while holding down the Bank button. To enter Individual Test mode: - Use the Value Dial to select which t

7、est to run (each test is described below). - Press Store to execute the test. When the test is complete, you can either select another test to run or exit Individual Test mode by holding Bank and pressing Store. - Power up the unit while holding down the Store button. To enter All Test mode: C4 Indi

8、vidual Test Descriptions 4 t0: ROM Test. If the unit passes, the MicroVerb 4 will display P0 and exit the test automatically. If the unit fails, the MicroVerb 4 will display F0 and wont exit the test. In this case, the user must press Bank to exit. 4 t1: EEPROM Test. If the unit passes, the MicroVer

9、b 4 will display P1 and exit the test automatically. If the unit fails, the MicroVerb 4 will display F1 and wont exit the test. In this case, the user must press Bank to exit. 4 t2: LED Test. Lights up all the LEDs (first, column by column; then row by row). The C4 automatically exits this test. 4 t

10、3: Switch/Encoder Test. Checks the buttons and the rotary encoder. The user must press every button AND rotate the encoder in both directions in order for the test to pass. After doing this, the user should hold Bank and press Store. If at this point all of the buttons have been pressed (i.e., the u

11、nit passed), then the MicroVerb 4 will display P3 and exit the test. If instead not all of the buttons have been pressed, the MicroVerb 4 will display F3. The user can either restart the test (by pressing Store) or exit the test (by pressing Bank.) 4 t4: Edit Knob Test. Checks the Edit A/B knobs. Th

12、e user must rotate each knob to show all values (0 to 127) in order for the test to pass. To exit the test, press Bank. 4 t5: MIDI In/Out Test. Before running this test the user must connect a MIDI cable from the MIDI Out to the MIDI In of the unit. If the unit passes, the MicroVerb 4 will display P

13、5 and exit the test. If the unit fails, the MicroVerb 4 will display F5 and wont exit the test. In this case, the user must press Bank to exit. 4 t6: DSP RAM Test. If the unit passes, the MicroVerb 4 will display P6 and exit the test automatically. If the unit fails, the MicroVerb 4 will display F6

14、and wont exit the test. In this case, the user must press Bank to exit. Additional Test Procedures Audio Test. Plug an audio source into the Left Input. Dont plug anything into the Right Input. Verify that audio is passed through (the Input meters should light). Next, test the Right Input (with noth

15、ing in the Left Input). Finally, plug a different audio source into each of the Inputs. Verify that the Left Output passes audio from the Left Input and verify that the Right Output passes audio from the Right Input. In addition, all knobs should be turned through the entire range to ensure 1. Audio

16、 potentiometers are smooth and there are no audio dropouts or “scratching” noises heard, and 2. Edit knobs/data wheels correctly switch/change the corresponding parameters in accordance with the units User Reference Manual. C4 Service Manual V1.01 RadioFans.CN 收音机爱 好者资料库 10-22-02 Troubleshooting Cha

17、rt The charts below were created in an effort to relieve the beleaguered technician from having to discover some of the common faults we have seen. Please note that we only cover the most likely causes, not all of them. C4 Symptom Possible Cause Solution No Lights, No Sound. (Dead). Faulty AC adapte

18、r. Replace and retest. Defective component in power supply circuit. Troubleshoot and repair as necessary. Loose front panel cable. Troubleshoot and repair as necessary. No wet (effects) signal. Faulty ASIC Replace and retest. Faulty DRAM Replace and retest. Faulty Crystal Replace and retest. Faulty

19、DAC Troubleshoot and repair as necessary. Faulty ADC Troubleshoot and repair as necessary. Distortion. Faulty Power Supply Rail Troubleshoot and repair as necessary. Faulty op-amp Troubleshoot and repair as necessary. Faulty DAC Troubleshoot and repair as necessary. Faulty ADC Troubleshoot and repai

20、r as necessary. Programs not changing. Faulty shaft encoder. Replace and retest. Intermittent operation. Faulty Crystal. Replace and retest. Faulty potentiometer(s) Replace and retest. Poor through hole Solder Check all through hole solder connections, particularly near the power supply area. C4 Ser

21、vice Manual V1.01 RadioFans.CN 收音机爱 好者资料库 10-22-02 General Troubleshooting While this manual assumes that the reader has a fundamental understanding of electronics and basic troubleshooting techniques, a review of some of the techniques used by our staff may help. 1. Visual Inspection - A short visu

22、al inspection of the unit under test will often yield results without the need of complex signal analysis (burnt, or loose components are a dead giveaway). 2. Self Test - Alesis products that utilize microprocessor control contain built in test software which exercises many of the units primary circ

23、uit functions. Self test should always be done following any repair to ensure basic functionality. 3. Environmental Testing - Applying heat and cold (heat gun/freeze spray) will often reveal thermally intermittent components (Clock crystals, I.C.s, and capacitors are particularly prone to this type

24、of failure). 4. Burn in Testing - Leaving a unit running overnight often reveals intermittent failures such as capacitors that begin to leak excess current after a significant amount of time. 5. Cable Checks - Wiggling cables can reveal intermittent failures such as loose cables or poorly soldered h

25、eaders. Remember to check power supply cables as well. 6. Flexing the PC Board - Poor solder joints and broken traces can often be found by pressing the PC Board in various places. 7. Tapping Components - Sometimes tapping on a component (particularly crystals) will cause it to fail. 8. Power Down/u

26、p - Turning the unit off and back on rapidly several times may reveal odd reset and/or power supply failures. 9. Reset Threshold - A Variac (variable transformer) can be used to check reset threshold levels. This can be particularly useful in helping customers with low line problems. 10. Compressors

27、 - Using a compressor/limiter is often helpful when attempting to solve low level noise problems, as well as assisting with DAC adjustments. 11. Sweep Tests - Sweep generators are very useful in checking the frequency response envelopes of anti-aliasing filters. 12.Piggybacking - Piggybacking I.C.s is particularly useful when troubleshooting large sections of logic. This is especially true when working with older units. C4 Service Manual V1.01