JBL-DSC1000-dsc-sm 电路图 维修手册.pdf

《JBL-DSC1000-dsc-sm 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《JBL-DSC1000-dsc-sm 电路图 维修手册.pdf（54页珍藏版）》请在收音机爱好者资料库上搜索。

1、DSC 1000 DIGITAL SIMPLY CINEMA SERVICE MANUAL The DSC 1000 Controller is shown here. RadioFans.CN 收音机爱 好者资料库 This Service Manual includes service information for ? DSC1000 head unit only. ? For service information on the speaker system see JBL ? SCS200.5 Service Manual ENGLISH DSC 1000 CONTROLLER SP

2、ECIFICATIONS DVD player Pickup:Semiconductor laser, wavelength 650nm Signal system:NTSC / PAL Video signal horizontal resolution:More than 480 lines (DVD) Video signal-to-noise ratio:More than 60 dB (DVD) Audio frequency response:DVD (PCM): 20Hz 22kHz (+/- 1.0dB) (Stereo) CD (PCM): 20Hz 20kHz (+/- 1

3、.0dB) Audio signal-to-noise ratio:More than 80 dB (PCM) Total harmonic distortion:Less than 0.01% (PCM) Dynamic range: DVD (PCM): More than 85 dB (EIAJ, 2kHz) CD: More than 85 dB (EIAJ) FM Tuner System:PLL quartz-locked digital synthesizer system Tuning range:87.50 108.00 MHz Antenna terminals:75 oh

4、ms, unbalanced Intermediate frequency:10.7 MHz Video Outputs Component Video Output: Y: 1 Vp-p/75 Ohms, sync negative polarity Cr: 0.7 Vp-p/75 Ohms Cb: 0.7 Vp-p/75 Ohms CVBS Video:1 Vp-p 75 ohms S-video: Y: 1 Vp-p 75 ohms C: PAL 0.3 Vp-p 75 ohms / NTSC 0.286 Vp-p 75 ohms Audio line Outputs Audio L/R

5、: 1 Vrms, 1 kilohms General Power requirements: AC 230 V, 50 Hz Power consumption: 20 W Dimensions (WxHxD): 431 x 75 x 352 mm, 17 x 3 x 14 Weight: 8.5 kg, 18.7 lb. * Designs and specifications are subject to change without notice. JBL continually strives to improve its products by introducing design

6、 refinements into existing models without notice. For this reason, the DSC 1000 systems may differ in some respects from the published specifications and descriptions, but will always equal or exceed the original specifications unless otherwise stated. CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINIT

7、ION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 OR 625 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT THE USER SWITCH THE CONNECTION TO THE STANDARD DEFINITION OUTPUT. IF THERE ARE QUESTIONS REGARDING OUR TV

8、 SET COMPATIBILITY WITH THIS MODEL 525p AND 625p DVD PLAYER, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. RadioFans.CN 收音机爱 好者资料库 1 SERVICING PRECAUTIONS NOTES REGARDING HANDLING OF THE PICK-UP 1. Notes for transport and storage 1) The pick-up should always be left in its conductive bag until immedia

9、tely prior to use. 2) The pick-up should never be subjected to external pressure or impact. 2. Repair notes 1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials. 2) The pick-up should always be handled correctly and carefully, taking care to avoid e

10、xternal pressure and impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or damage to the printed-circuit board. 3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason the adjustment point an

11、d installation screws should absolutely never be touched. 4) Laser beams may damage the eyes! Absolutely never permit laser beams to enter the eyes! Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged. 5) Cleaning the lens surface If there is dust on

12、the lens surface, the dust should be cleaned away by using an air bush (such as used for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cot- ton swab should be used, taking care not to distort this. 6) Never attempt to disassemble the pick-up. Sprin

13、g by excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab. (Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up. Storage in c

14、onductive bag NEVER look directly at the laser beam, and dont let contact fingers or other exposed skin. Magnet How to hold the pick-up Conductive Sheet Cotton swab Pressure Pressure Drop impact RadioFans.CN 收音机爱 好者资料库 2 NOTES REGARDING COMPACT DISC PLAYER REPAIRS 1. Preparations 1) Compact disc pla

15、yers incorporate a great many ICs as well as the pick-up (laser diode). These compo- nents are sensitive to, and easily affected by, static electricity. If such static electricity is high voltage, components can be damaged, and for that reason components should be handled with care. 2) The pick-up i

16、s composed of many optical components and other high-precision components. Care must be taken, therefore, to avoid repair or storage where the temperature of humidity is high, where strong magnetism is present, or where there is excessive dust. 2. Notes for repair 1) Before replacing a component par

17、t, first disconnect the power supply lead wire from the unit 2) All equipment, measuring instruments and tools must be grounded. 3) The workbench should be covered with a conductive sheet and grounded. When removing the laser pick-up from its conductive bag, do not place the pick-up on the bag. (Thi

18、s is because there is the possibility of damage by static electricity.) 4) To prevent AC leakage, the metal part of the soldering iron should be grounded. 5) Workers should be grounded by an armband (1M) 6) Care should be taken not to permit the laser pick-up to come in contact with clothing, in ord

19、er to prevent static electricity changes in the clothing to escape from the armband. 7) The laser beam from the pick-up should NEVER be directly facing the eyes or bare skin. Resistor (1 Mohm) Conductive Sheet Resistor (1 Mohm) Armband 3 ESD PRECAUTIONS Electrostatically Sensitive Devices (ESD) Some

20、 semiconductor (solid state) devices can be damaged easily by static electricity. Such components com- monly are called Electrostatically Sensitive Devices (ESD). Examples of typical ESD devices are integrated cir- cuits and some field-effect transistors and semiconductor chip components. The follow

21、ing techniques should be used to help reduce the incidence of component damage caused by static electricity. 1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any electrostatic charge on your body by touching a known earth ground. Alternatively,

22、 obtain and wear a commercially available discharging wrist strap device, which should be removed for potential shock reasons prior to applying power to the unit under test. 2. After removing an electrical assembly equipped with ESD devices, place the assembly on a conductive sur- face such as alumi

23、num foil, to prevent electrostatic charge buildup or exposure of the assembly. 3. Use only a grounded-tip soldering iron to solder or unsolder ESD devices. 4. Use only an anti-static solder removal device. Some solder removal devices not classified as anti-static can generate electrical charges suff

24、icient to damage ESD devices. 5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESD devices. 6. Do not remove a replacement ESD device from its protective package until immediately before you are ready to install it. (Most replacement ESD devices are

25、 packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive materials). 7. Immediately before removing the protective material from the leads of a replacement ESD device, touch the protective material to the chassis or circuit assembly into which the

26、 device will by installed. CAUTION : BE SURE NO POWER IS APPLIED TO THE CHASSIS OR CIRCUIT, AND OBSERVE ALL OTHER SAFETY PRECAUTIONS. 8. Minimize bodily motions when handing unpackaged replacement ESD devices. (Otherwise harmless motion such as the brushing together of your clothes fabric or the lif

27、ting of your foot from a carpeted floor can gen- erate static electricity sufficient to damage an ESD device). DSC1000 Component list ItemParts No.QtySPECIFICATIONRemarks(English) 1380-B0DSC100-80001Chassis 2380-ADSC1000-85001Top cover 3380-CDSC1000-05001Back panel 4332-3DSCPT04-00001Loader support

28、5332-3DSCPT05-00001Power button support 6332-3DSCPT06-00002Len support 7332-3DSCPT07-00001Heat-sink support 8385-01459545-52001Heat-sink 9385-00161235-52002Heat-sink, for SMPS D17 D18 10385-00501935-52001Heat-sink, for SMPS Q16 11385-VD31ZPA2-50001Aluminium alloy front panel 12332-7DSCPT11-00002Net

29、cover on front panel 13330-ADSCPT12-00001Baffle for tray door 14600-000H0205-00201Amplifier speaker output label 15385-00282810-00001Heat-sink, for MainBoard U4 16332-10MV7200-00002Decorate lamp holder MV7200 17500-09130126-00001Insulated underlay for AC cord 130126mm 18500-10202011-00101Insulated u

30、nderlay for SMPS 202011mm 19331-1000RE01-80001Button 20331-1000RE02-80001Power button 21330-2000RE03-80001Disc tray door 22331-8000RE04-80001Len for tray door 23331-8000RE05-80001Len for VFD VFD 24330-ADSCRE06-00001Left baffle 25330-ADSCRE07-00001Right baffle 26331-5VD28016-70001Power indicator lamp

31、shade 27331-3000RE12-00001Volume knob 28331-4DSC1000-40004Pedestal bronzing, size same as DVD 25, specify color 29350-0DSC1000-00004Pedestal underlay same as DVD25 30332-200SZ003-02001IR receiver head frame SZ003 282810mm DSC1000-RE01 DSC1000-RE02 DSC1000-RE03 DSC1000-RE04 DSC1000-RE05 DSC1000-RE12

32、DSC1000-PT03 DSC1000-PT04 DSC1000-RE08 DSC1000-PT12 DSC1000-H02 DSC1000-RE07 DSC1000-PT11 DSC1000-PT09 DSC1000-RE06 METAL PART PLASTIC PART DSC1000-PT05 DSC1000-PT06 DSC1000-PT07 DSC1000-PT08, 1459545mm DSC1000-PT01 16X12X35mm 50X19X35mm DSC1000-PT02 Harman Consumer GroupComponentsJBL DSC1000/230 DS

33、C1000 Component list 31350-00202006-02002VFD soft pad VFD20mm20mm6mm 32331-7C035040-00102Alumium fastenercover pyrocondensation cannula F340mm 33500-70000000-00001Plastic fastener fasten the power cord 34332-40000000-00006Screw map 35500-02000000-00302Lead nip 36500-01025015-000123M double glue 3M25

34、15mm 37332-20007008-000011PCB plastic frame PCBF78.6mm 38500-09002024-00001Talc piece for SMPS Q6F2024mm 39350-00161101-26003 Diathermanous Selenium Rubber place on Amp Board AU1 AU2 AU3 16111mm 40331-90033702-Q2001Shade for volume knob F33F70.2mm 41500-10200702-00002Sponge with double glue 2072mm 4

35、2555-A01000RC-00101 set Remote control 43162-J00TJC13-02001JBL speaker jack TJC1-3 JBL TJC1-3Red 032C with JBL logo 44162-J00TJC13-01001JBL speaker jack TJC1-3 JBL TJC1-3Whtie with JBL logo 45162-J00TJC13-05001JBL speaker jack TJC1-3 JBL TJC1-3Green 361C with JBL logo 46162-J00TJC13-03001JBL speaker

36、 jack TJC1-3 JBL TJC1-3Cool Grey 7C with JBL logo 47162-J00TJC13-06001JBL speaker jack TJC1-3 JBL TJC1-3Process Blue C with JBL logo 48331-90146258-05001VFD filter VFDfor VFD 14625.8mm 49500-05022050-00001Pyrocondensation cannula cover magnetism annulus of AC cord f 2250mm 50205-0JSHM248-10001Magnet

37、ism annulus M248for AC cord 51313-AGDSC100-00011Laser precausion mark stick on loader 52313-AGDSC100-00021Laser precausion guide stick on loader 53500-01012060-00102Viscose band1260mm 54160-E0050250-0A001 5 pin, long 250mm, two ends with 2.0mm space connector, different link sides connect loader and

38、 mainboard 55160-E0060320-0A001 6 chip, long 320mm, two ends with 2.0mm space connector, different link sides connect loader and mainboard 56160-E0020040-0A001 2 pin, long 40mm, one end with 2.54mm space connector connect front panel board and power switch 57160-E0090230-0A001 9 pin, long 230mm, two

39、 ends with 2.0mm space connector, same link sides connect front panel board and mainboard CONNECT CABLE Harman Consumer GroupComponentsJBL DSC1000/230 DSC1000 Component list 58160-E0100160-0A001 10 pin, long 160mm, one end with 2.0mm connector and another end with 2.54mm connector, different link si

40、des connect power supplier board and mainboard 59160-E0050180-0A001 5 pin, long 180mm, one end with 2.0mm connector and another end with 2.54mm connector, same link sides connect power supplier board and amplifier board 60160-EG020180-0A001 2 pin, long 180mm, two ends with VH-3Y connector, different

41、 link sides connect power supplier board and amplifier board 61161-16070100-00001 16 pin, long 50mm, 1.0mm space, flat cable, same link sides connect mainboard and amplifier board 62161-24070050-00001 11 pin, long 70mm, 1.25mm space, flat cable, same link sides connect mainboard and tuner model 6316

42、0-E0050340-5A001 5 pin with shield, long 340mm, two ends with 2.0mm space connector, same link sides connect front panel board and mainboard 64160-E0020600-2A0012 pin, long 600mm, one end with VH-3Y connectorconnect power supplier board and power switch 65160-E0240170-JA001 24 pin, long 170mm, 0.5mm

43、 space, flat cable, different link sides connect loader and mainboard 66160-E0030060-3A001 3 pin, long 60mm, two ends with 2.54mm space connector, same link sides connect power supplier board and front panel board 67162-A0000350-00001 Power cord with 350mm fixture, with magnetism annulus EU version

44、68162-A0000042-000011 pin with 42 line, one end with alumium fastener connect A point with B point of Q6 on SMPS 69206-0000DV34-22021LOADERSANYO DV34 70555-A01000RC-00101Remote controlDSC1000 71 170-APS5EA07-0000 1 Power switch (20mm) PS5E-A-078 204-001E803A-0300 TFCF1E803A, for EU version, 73300-C1

45、239CPV-00021Mainboard1239C-PV1 74300-O01241C-00021Amplifier board1241C 75300-D001242C-00021Front panel board1242C 76300-K001354C-00011Remote control board1354C FM tuner model1 WHOLE PART ASSEMBLED PCB 72 Harman Consumer GroupComponentsJBL DSC1000/230 DSC1000 Component list 77300-A001356C-00011Power

46、supplier board1356C 78310-0DSC1000-00101White cartonhouse DSC1000 79310-0DSC1000-00201Master cartonhouse DSC1000 and speaker system 80309-0DSC1000-00002Polyfoam 81311-54049522-11001Plastic bag for unit540495T0.8 82311-25035012-22001Plastic bag for users manual250350 83311-15523011-22001Plastic bag f

47、or speaker cables155230 84311-15523011-22001Plastic bag for AV cables155230 85311-26010011-22001Plastic bag for remote control 260100 86555-A01000RC-00101Remote controlDSC1000 87202-00000711-120027# batteryGP band 88312-AH100000-00101Users manualEU version 89162-GSCART15-00001SCART cable1.5 meters 9

48、0162-J0000005-02001Speaker cable5 meters with red jack 91162-J0000005-01001Speaker cable5 meters with white jack 92162-J0000005-05001Speaker cable5 meters with green jack 93162-J0000012-03001Speaker cable12 meters with grey jack 94162-J0000012-06001Speaker cable12 meters with blue jack 95162-KFM0000

49、0-00001FM tuner cabletuner antenna ACCESSORIES PACKING PART Harman Consumer GroupComponentsJBL DSC1000/230 DSC1000 FRONT BOARD ItemParts No.QtyLOCA.NO.DESCRIPTIONSPECIFICATIONRemarks 1131-B00000JT-000023R40 3R41Resistor, chip0O 1/8W 0805 5% 2131-B00000JT-000023R15 3R21Resistor, chip0O 1/8W 0805 5% 3131-B01010JT-000033R17 3R19 3R38Resistor, chip100O 1/8W 0805 5% 4131-B01047JT-000013R7Resistor, chip470O 1/8W 0805 5% 5131-B02010JT-000013R4Resistor, chip1KO 1/8W 0805 5% 6131-B02022JT-000013R24Resistor, chip2.2KO 1/8W 0805 5% 3R3 3R9 3R10