Bogen-WMK1-Operation-Manual 电路图维修手册.pdf

上传人：cc518

文档编号：333652

上传时间：2026-07-03

格式：PDF

页数：2

大小：652.62KB

《Bogen-WMK1-Operation-Manual 电路图维修手册.pdf》由会员分享，可在线阅读，更多相关《Bogen-WMK1-Operation-Manual 电路图维修手册.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、DESCRIPTION The Bogen Model WMK1 is a flush in- wall mounting cabinet designed to accommodate Models C10, C20, and CAM2. The cabinet fits between standard 2 x 4 s on 16 center wall studs, with the front panel acting as a plaster ring. Controls are acces- sible via a tilt- open door that may be locke

2、d in either the closed or open position. The cabinet is finished in black and is made from sturdy 16- gauge steel. I t is supplied with a backbox which includes an easily mounted AC power receptacle. DIMENSIONS & WEIGHT Wal l Box14W x 13- 1/ 2H x 3- 1/ 2D Face Pl at e16W x 14- 1/ 2H Ti l t -Open Doo

3、r11- 5/ 8W x 8- 3/ 8H Mi ni mum, Openi ng Requi red14- 1/ 8W x 13- 5/ 8H Shi ppi ng Wei ght13 lbs. INSTALLATION ACCESSIBILITY:The backbox must be placed so that the controls are at an appropriate height for operation. Typically , the bottom of the backbox should be three feet above the floor. MOUNTI

4、NG:The flush- mounting backbox must be secured to support surfaces inside the wall or, in new construction, must be built into the wall. The WMK1 is shipped with the front panel and door assembly temporarily secured to the backbox. Remove the assembly from the backbox and mount the box with four scr

5、ews through the slotted holes ( see mounting diagram on the back of this sheet) . Use these slotted holes to position the box so that it is flush with the surface of the finished wall. When this is accomplished, add four more screws through the holes just forward of the slotted holes. Securely tight

6、en all eight screws to prevent any further movement of the backbox. The AC recepta- cle must be located at the top of the backbox. The wall cutout for the backbox should be 14- 1/ 8 wide and 13- 5/ 8 high. WIRING:The backbox has a conduit entry above the receptacle box which must be used for AC line

7、 connection. ( This is the knockout between two small screw holes. ) Where possible, locate the backbox near a suitable #14 AWG, 3- wire single- phase, 120V AC line. Use wire nuts to connect the recep- tacle. The box must be convenient for connection of micro- phone input cables and speaker lines. A

8、ll wires enter the box inside the wall. CAUTION Do not locate box or connecting wires near steam lines or other heat sources. INSTALLATION OF THE AMPLIFIER:The amplifier is secured to the door of the WMK1 by four screws. A separately mounted flange on the door provides a stop for the door and, when

9、removed, allows the amplifier to be dropped down for connections. Audio cables may be brought into the backbox through any knockout other than that used for the AC line. Ti l t -open door Can be l ocked i n cl osed or open posi t i on Used wi t h model s C10, C20, 10- and 20-wat t ampl i f i ers, an

10、d CAM2 mi xer ampl i f i ers MODEL WMK1 WALL MOUNT CABINET 2000 Bogen Communicat ions , Inc. Specificat ions ar e s ubject t o change wit hout not ice 54-5634-07C 1202 RadioFans.CN 收音机爱好者资料库 1. With the wall box mounted, use wire nuts to connect AC wiring. I nstall the AC receptacle in the top of t

11、he box using two #8 x sheet metal screws. 2.Bring all input and output wiring into the wall box, including the speaker wires, through knockouts in the backbox. 3. Before installing the front panel on the wall box, install the lock. 4. Make sure that the locking cam is down when in the locked positio

12、n. 5. Mount the front panel and door assembly to the wall box with #8 x 1- 1/ 4 sheet metal screws. 6. Mount the Tinnerman clips on the sides of the wall box. 7. Remove the feet from the amplifier. I nstall the amplifier mounting screws in the door, using the feet to hold the screws in place. Mount

13、the amplifier to the front door. 8. Connect speaker and input wiring to the amplifier. 9. Plug the amplifier into the AC receptacle. 10.Raise the door to a level which allows the door stop to be installed. 11. Mount door stop with two #6 by sheet metal screws. 12.Assure that the door lock operates correctly . 50 Spr ing St r eet , Rams ey, NJ 07446 Tel : 201-934-8500 Fax : 201-934-9832 1A & 1B. Ref er t o t he mount i ng di agram and proceed as f ol l ows: RadioFans.CN 收音机爱好者资料库