Marantz-VP-12-S-1-Control-Specification 电路图 维修手册.pdf

《Marantz-VP-12-S-1-Control-Specification 电路图 维修手册.pdf》由会员分享，可在线阅读，更多相关《Marantz-VP-12-S-1-Control-Specification 电路图 维修手册.pdf（9页珍藏版）》请在收音机爱好者资料库上搜索。

1、 PC Control Specification for VP-12S1 Marantz Japan, Inc. Marantz Software Center Aug. 21, 2001 Rev. 1.2 RadioFans.CN 收音机爱 好者资料库 PC Control Specification for VP-12S1 2 1. PC Control Interface * RS-232C(Straight Cable) * Baud rate:. 9600 bps * Data length: . 8 bits * Parity: . None * Stop bit:. 1 bit

2、 * Flow Control: . RTS/CTS * Communication procedure: . Full duplex 2. PC Control Command Reference 2.1. Command Communications Sequence Projector returns ACK, NAK, or Status after reception of Command within 1 second. An ASCII code is used for data. It is discriminated whether transmitting characte

3、r sequences are a capital letter and a small letter. Although there is no distinction of a capital letter small letter, let a capital letter be a standard. Command transmission and Status reply add Start Character and End Character as follows. Start Character : End Character : 0 x0D Command Sample :

4、 PWR?, 0 x0D (Request Power Status) Feedback Sample : PWR1, 0 x0D, 0 x0A(Power Status = On) ACK and NAK use the following control code. ACK(Reception success) :0 x06, 0 x0D, 0 x0A NAK(Reception failure) :0 x15, 0 x0D, 0 x0A A reception side cancels data before . When 0 x0D comes, with not coming, NA

5、K (reception failure) is returned. That which made Hex the ASCII code is used for transmission and reception of digital data. Between a command and a numerical value, / is inserted as a delimiter. For Example: When 26(decimal) of the number is expressed 1, A0 x31, 0 x41 2.2. Normal Command It is Com

6、mand which demands processing. In data other than an appointed command, or the state where does not come, when 0 x0D comes, it becomes reception failure, and NAK is returned. RadioFans.CN 收音机爱 好者资料库 PC Control Specification for VP-12S1 3 Commands, such as Power On Command at the time of notes Standb

7、y (Fan operation), return only ACK, when processing is not carried out. For example: When Power On is sent to Projector. Command transmission from PC. PWR, 0 x0D After Command processing end and from a projector to a reply 0 x06, 0 x0D, 0 x0A (ACK reception success) or 0 x15, 0 x0D, 0 x0A (NAK recep

8、tion failure) 2.3. Request Status Command It is Command which demands Status. Projector returns Status or NAK. In data other than an appointed command, or the state where does not come, when 0 x0D comes, it becomes reception failure, and NAK is returned. For Example: When Power Status is requested t

9、o Projector. Command transmission from PC. PWR?, 0 x0D After Command processing end and from a projector to a reply PWR1, 0 x0D, 0 x0A (Power On) or PWR0, 0 x0D, 0 x0A (Standby) or 0 x15, 0 x0D, 0 x0A (NAK reception failure) RadioFans.CN 收音机爱 好者资料库 PC Control Specification for VP-12S1 4 2.4. Normal

10、Command List Command Character Example Power On PWR1 PWR1, 0 x0D Power Standby PWR0 PWR0, 0 x0D Component CMP CMP, 0 x0D S-Video SVD SVD, 0 x0D Video VDO VDO, 0 x0D RGB RGB RGB, 0 x0D Source Aux. AUX AUX, 0 x0D Theater1 THE1 THE1, 0 x0D Theater2 THE2 THE2, 0 x0D Theater3 THE3 THE3, 0 x0D Theater Def

11、ault THED THED, 0 x0D Standard 1 STD1 STD1, 0 x0D Standard 2 STD2 STD2, 0 x0D Standard 3 STD3 STD3, 0 x0D Standard Default STDD STDD, 0 x0D Dynamic 1 DYN1 DYN1, 0 x0D Dynamic 2 DYN2 DYN2, 0 x0D Dynamic 3 DYN3 DYN3, 0 x0D Memory Dynamic Default DYND DYND, 0 x0D Normal NML NML, 0 x0D Through THRH THRH

12、, 0 x0D Full FULL FULL, 0 x0D Aspect Zoom ZOOM ZOOM, 0 x0D V-Mute On MUT1 MUT1, 0 x0D V-Mute V-Mute Off MUT0 MUT0, 0 x0D Keystone V+ KEYV+ KEYV+, 0 x0D Keystone V- KEYV- KEYV-, 0 x0D Keystone V Keystone V # KEYV/# KEYV/0F, 0 x0D Keystone H+ KEYH+ KEYH+, 0 x0D Keystone H- KEYH- KEYH-, 0 x0D Keystone

13、H Keystone H # KEYH/# KEYH/0F, 0 x0D Focus On FOC1 FOC1, 0 x0D Focus Focus Off FOC0 FOC0, 0 x0D Black Setup 0IRE BSET0 BSET0, 0 x0D Black Setup Black Setup 7.5IRE BSET7 BSET7, 0 x0D Lamp Mode High LMODEH LMODEH, 0 x0D Lamp Mode Lamp Mode Low LMODEL LMODEL, 0 x0D Adjustment range Command Minimum Cent

14、er Maximum Keystone V -1E (-30) 0 (0) +1E (+30) Keystone H -14 (-20) 0 (0) +14 (+20) PC Control Specification for VP-12S1 5 2.5. Request Status Command List Request Status Request Command Answer Example On PWR1, 0 x0D, 0 x0A Power PWR?, 0 x0D Standby PWR0, 0 x0D, 0 x0A Component CMP, 0 x0D, 0 x0A S-

15、Video SVD, 0 x0D, 0 x0A Video VDO, 0 x0D, 0 x0A RGB RGB, 0 x0D, 0 x0A Source SRC?, 0 x0D AUX. AUX, 0 x0D, 0 x0A Theater1 THE1, 0 x0D, 0 x0A Theater2 THE2, 0 x0D, 0 x0A Theater3 THE3, 0 x0D, 0 x0A Theater Default THED, 0 x0D, 0 x0A Standard 1 STD1, 0 x0D, 0 x0A Standard 2 STD2, 0 x0D, 0 x0A Standard

16、3 STD3, 0 x0D, 0 x0A Standard Default STDD, 0 x0D, 0 x0A Dynamic 1 DYN1, 0 x0D, 0 x0A Dynamic 2 DYN2, 0 x0D, 0 x0A Dynamic 3 DYN3, 0 x0D, 0 x0A Memory MEM?, 0 x0D Dynamic Default DYND, 0 x0D, 0 x0A Normal NML, 0 x0D, 0 x0A Through THRH, 0 x0D, 0 x0A Full FULL, 0 x0D, 0 x0A Aspect ASP?, 0 x0D Zoom ZO

17、OM, 0 x0D, 0 x0A On MUT1, 0 x0D, 0 x0A V-Mute MUT?, 0 x0D Off MUT0, 0 x0D, 0 x0A Keystone V KEYV?, 0 x0D 12 KEYV/+0C, 0 x0D, 0 x0A Keystone H KEYH?, 0 x0D 20 KEYH/+14, 0 x0D, 0 x0A On FOC1, 0 x0D, 0 x0A Focus FOC?, 0 x0D Off FOC0, 0 x0D, 0 x0A 0IRE BSET0, 0 x0D, 0 x0A Black Setup BSET?, 0 x0D 7.5IRE

18、 BSET7, 0 x0D, 0 x0A HIGH LMODEH, 0 x0D, 0 x0A Lamp Mode LMODE?, 0 x0D LOW LMODEL, 0 x0D, 0 x0A No Error “Error : None”, 0 x0D, 0 x0A Error Status*1 ERR?, 0 x0D Lamp Door Open “Error : Door Open”,0 x0D, 0 x0A Version*2 VER?, 0 x0D Version 01.00 0100, 0 x0D, 0 x0A Instruction “?”, 0 x0D Display Comma

19、nd *1 The contents of Error are indicated separately. *2 Version number shows Version of a RC-232C Command group. PC Control Specification for VP-12S1 6 2.6. Special Command List Request Status Request Command Example Gamma Set at Standard GSSTD/# GSSTD/04, 0 x0D Gamma Set at Dynamic GSDYN/# GSDYN/0

20、5, 0 x0D Gamma Set Gamma Set at Theater GSTHE/# GSTHE/06, 0 x0D C Temp. Red at Low*2 CTAL/R/# CTAL/R/012, 0 x0D C Temp. Green at Low CTAL/G/# CTAL/G/345, 0 x0D C Temp. Blue at Low CTAL/B/# CTAL/B/678, 0 x0D C Temp. Red at Mid. *2 CTAL/R/# CTAM/R/9AB, 0 x0D C Temp. Green at Mid. CTAM/G/# CTAM/G/CDE,

21、0 x0D C Temp. Blue at Mid. CTAM/B/# CTAM/B/F01, 0 x0D C Temp. Red at High*2 CTAL/R/# CTAH/R/234, 0 x0D C Temp. Green at High CTAH/G/# CTAH/G/567, 0 x0D Color Temp Adjust Value Set*1 C Temp. Blue at High CTAH/B/# CTAH/B/89A, 0 x0D C Temp at Low CTAL? “CTAL?” C Temp at Mid. CTAM? “CTAM?” C Temp at Hig

22、h CTAH? “CTAH?” Color Temp Value Get Answer R = 10, G = 11, B= 20 “R=0 x000A/G=0 x000B/B=0 x0 014” , 0 x0D, 0 x0A C Temp Low CTL “CTL”, 0 x0D, 0 x0A C Temp Mid. CTM “CTM”, 0 x0D, 0 x0A Color Temp Mode Set C Temp High CTH “CTH”, 0 x0D, 0 x0A *1 It becomes effective, after Setting Color Temp Mode *2 U

23、sually, it is not used. Status Request Sample Answer Sample Voltage B “BINVOL/1” ACK 0 x06,0 x0D,0 x0a Voltage C “BINVOL/2” ACK 0 x06,0 x0D,0 x0a Voltage D “BINVOL/3” ACK 0 x06,0 x0D,0 x0a Voltage E “BINVOL/4” ACK 0 x06,0 x0D,0 x0a Bin Voltage Voltage? “BINVOL?” Voltage B “BINVOL/1” Index Delay 3 “C

24、WA/DELAY/3” ACK 0 x06,0 x0D,0 x0a Color Wheel Adjust Index Delay? “CWA/DELAY?” Index Delay 5 “CWA/DELAY/0005” Adjustment range Command Minimum Center Maximum Color Temp Adjust Set 0 (0) - FFF(+3.99902) Color Wheel Adjust 0 (0) - 2CF(719) Request Status Request Command Answer Sample V=60 Hz,H=525 Lin

25、es,C=550 Lines Read Sync “SYNC?”, 0 x0D “V=6400/H=020D/C=0226”,0 x0D, 0 x0A Read Build Num. “BUILD?”, 0 x0D Build 0025 “0025”, 0 x0D, 0 x0A Read Boot Program Version “BOTVER?”,0 x0D Boot Ver. 00.10 “0010”, 0 x0D, 0 x0A Read Firmware Program Version “FRMVER?”,0 x0D Firmware Ver. 00.10 “0010”, 0 x0D,

26、0 x0A Read Order “ORDER?”,0 x0D 413V “413V” , 0 x0D, 0 x0A Instruction for Engineer “?” Display Command for Engineer PC Control Specification for VP-12S1 7 The meaning of the parameter in Gamma Set command is described below. Parameter Description 00 Select a Gamma Table 1 defined by Texas Instrumen

27、ts in HDFP 01 Select a Gamma Table 2 defined by Texas Instruments in HDFP 02 Select a Gamma Table 3 defined by Texas Instruments in HDFP 03 Reserved 04 Select a Gamma Table 1 defined by Texas Instruments in HDFP u-com 05 Select a Gamma Table 2 defined by Texas Instruments in HDFP u-com 06 Select a G

28、amma Table 3 defined by Texas Instruments in HDFP u-com 07 Select a Gamma Table 4 defined by Texas Instruments in HDFP u-com 08 Select a Gamma Table 5 defined by Texas Instruments in HDFP u-com 09 Select a Gamma Table 6 defined by Texas Instruments in HDFP u-com 0A Select a Gamma Table 7 defined by

29、Texas Instruments in HDFP u-com 0B Select a Gamma Table 8 defined by Texas Instruments in HDFP u-com 0C Select a Gamma Table 9 defined by Texas Instruments in HDFP u-com 0D Select a Gamma Table 1 defined by User(MJI) in EEPROM 0E Select a Gamma Table 2 defined by User(MJI) in EEPROM 0F Select a Gamm

30、a Table 3 defined by User(MJI) in EEPROM PC Control Specification for VP-12S1 8 It is asked for frequency by the following formulas from the return value of V Sync. In addition, since return value is Hex, be careful. 10288.12 8 1 6 Hzfrequency valuereturn = Build Number expresses the thing of a sub

31、microcomputer. Boot Program Version number the thing of a sub microcomputer. Firmware Program Version number the thing of a sub microcomputer. ?I2C Direct Write Command IICW/#/#/# For Example: When 0 xDF value is written in Device Address = 0 x88 and Sub Address = 0 x02 IICW/88/02/DF For Example: Wh

32、en 0 x12 is written in Device Address = 0 x46 and Sub-Address=specification-less IICW/46/-/12 ? I2C Direct Read Command IICR/#/# For Example: When read-out is performed from Device Address = 0 x89 and Sub Address = 0 x01. The read value presupposes that it was 0 xAA. IICR/89/01 AA/ It is the charact

33、er sequence returned from Sub u-com. For Example: When read-out is performed from Device Address = 0 x47 and Sub-Address = specification-less . The read value presupposes that it was 0 x23. IICR/47/- 23/ It is the character sequence returned from Sub u-com. PC Control Specification for VP-12S1 9 ? U

34、ser Gamma Table rewriting command It is the command which rewrites User Gamma Table which has three for R, G, and every B. Commands are as follows. UG/1/R.The command which rewrites R Table of User Gamma Table 1 UG/1/G.The command which rewrites G Table of User Gamma Table 1 UG/1/B.The command which

35、 rewrites B Table of User Gamma Table 1 UG/2/R.The command which rewrites R Table of User Gamma Table 2 UG/2/G.The command which rewrites G Table of User Gamma Table 2 UG/2/B.The command which rewrites B Table of User Gamma Table 2 UG/3/R.The command which rewrites R Table of User Gamma Table 3 UG/3

36、/G.The command which rewrites G Table of User Gamma Table 3 UG/3/B.The command which rewrites B Table of User Gamma Table 3 Command forms are as follows. CR is 0 x0d, 0 x0A. UG/1/R CR/ R Table rewriting of User Gamma Table1 is specified. 0123 CR/ ASCII (Hex) character describes Gamma value. 4567 CR/

37、 If it is 0 x4567, it will be described as 4567. 89AB CR/ 512 value per command is transmitted. CDEF CR/ Check every one thing which Com Device completed transmission at the time of transmission of gamma value. ? 0123 CR Complete CR / This character sequence is transmitted from VP12. It is the comma

38、nd that reads User Gamma. Commands are as follows UG?/1/R .The command which read R Table of User Gamma Table 1 Command forms are as follows UG/1/R CR/ R Table reading of User Gamma Table1 is specified. / The following is received from VP12 0123 CR/ ASCII (Hex) character describes Gamma value. 4567 CR/ If it is 0 x4567, it will be described as 4567. 89AB CR/ 512 value per command is received. ? 0123 CR/ The 512th word.