Philips-DVDR-3408-Service-Manual电路原理图.pdf
《Philips-DVDR-3408-Service-Manual电路原理图.pdf》由会员分享,可在线阅读,更多相关《Philips-DVDR-3408-Service-Manual电路原理图.pdf(71页珍藏版)》请在收音机爱好者资料库上搜索。
1、. Technical Specifications.1-2 . Safety Instruction, Warning 5060 Hz Power Consumption: 28 W Standby power consumption: 4.0W Dimensions : Set Dimensions (W X H X D): 427 X 48 X 318mm Net Weight : 3.18 Kg Specifications subject to change without prior notice. 1-2Safety instructions 1. General safety
2、Safety regulations require that during a repair: . Connect the unit to the mains via an isolation transformer. . Replace safety components indicated by the symbol , only by components identical to the original ones. Any other component substitution (other than original type) may increase risk of fir
3、e or electrical shock hazard. Safety regulations require that after a repair, you must return the unit in its original condition. Pay, in particular, attention to the following points: . Route the wires/cables correctly, and fix them with the mounted cable clamps. . Check the insulation of the mains
4、 lead for external damage. . Check the electrical DC resistance between the mains plug and the secondary side: 1) Unplug the mains cord, and connect a wire between the two pins of the mains plug. 2) Set the mains switch the “on” position (keep the mains cord unplug). 3) Measure the resistance value
5、between the mains plug and the front panel, controls, and chassis bottom. 4) Repair or correct unit when the resistance measurement is less than 1M. 5) Verify this, before you return the unit to the customer/user (ref. UL-standard no. 1492). 6) Switch the unit “off”, and remove the wire between the
6、two pins of the mains plug. 2.Laser safety This unit employs a laser. Only qualified service personnel may remove the cover, or attempt to service this device (due to possible eye injury). Laser device unit Type : Semiconductor laser : InGaAIP (DVD) : AIGaAs (CD) Wavelength : 658nm (DVD) : 783nm (CD
7、) Power out objective lens: 1.0mW (DVD read) : 1.2mW (CD read) Note: Use of controls or adjustments or performance of procedure other than those specified herein, may result in hazardous radiation exposure. Avoid direct exposure to beam. Safety instruction, Warning & Notes1-3Warning1.General . All I
8、Cs and many other semiconductors are susceptible to electrostatic discharges (ESD). Careless handing during repair can reduce life drastically. Make sure that, during repair, you are at the same potential as the mass of the set by a wristband with resistance. Keep components and tools at this same p
9、otential. Available ESD protection equipment: 1) Complete kit ESD3 (small tablemat, wristband, connection box, extension cable and earth cable) 4822 310 10671. 2) Wristband tester 4822 344 13999. . Be careful during measurements in the live voltage section. The primary side of the power supply , inc
10、luding the heat sink, carries live mains voltage when you connect the player to the mains (even when the player is “off”!). It is possible to touch copper tracks and/or components in this unshielded primary area, when you service the player. Service personnel must take precautions to prevent touchin
11、g this area or components in this area. A “lighting stroke” and a stripe-marked printing on the printed wiring board, indicate the primary side of the power supply. . Never replace modules, or components, while the unit is “on”. 2. Laser . The use of optical instruments with this product will increa
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- PhilipsDVDR3408ServiceManual 电路 原理图