Philips-FWC-200-Service-Manual电路原理图.pdf

《Philips-FWC-200-Service-Manual电路原理图.pdf》由会员分享，可在线阅读，更多相关《Philips-FWC-200-Service-Manual电路原理图.pdf（86页珍藏版）》请在收音机爱好者资料库上搜索。

1、CLASS 1LASER PRODUCTCOMPACTDIGITAL AUDIOService ManualServiceServiceServiceSPR 00 0054FW-C200/21/21M/30TABLE OF CONTENTSPageLocation of pc boards fr Reparaturen sind Original-Ersatzteile zu verwenden.ILe norme di sicurezza esigono che lapparecchio venga rimessonelle condizioni originali e che siano

2、utilizzati i pezzi di ricambioidentici a quelli specificati.“After servicing and before returning set to customer perform aleakage current measurement test from all exposed metal parts toearth ground to assure no shock hazard exist. The leakage currentmust not exceed 0.5mA.“CLASS 1LASER PRODUCT3122

3、110 03420GB Warning !Invisible laser radiation when open.Avoid direct exposure to beam.S Varning !Osynlig laserstrlning nr apparaten r ppnad och sprrenr urkopplad. Betrakta ej strlen.SF Varoitus !Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiinankymttmlle laseristeilylle. l katso ste

4、eseen!DK Advarse !Usynlig laserstrling ved bning nr sikkerhedsafbrydere erude af funktion. Undg udsaettelse for strling.1-6PCS 90 1152-1SPR 00 00573DIGITALSOUND CONTROLSTANDBY-ONPROGRAM DIMFULL AUTO STOPPLAYBACKPLAY/RECMINI HIFI SYSTEMCD1 2 3BANDTAPE1 2TAPECDTUNERAUXPRESETTUNINGSTOPCLEARSEARCHPLAY P

5、AUSEPREVNEXTDISC CHANGEDISC 3OPENCLOSEDC3CHANGER3CDROTARYCHANGERSYSTEMCDREWRITABLECOMPATIBLECDSYNCHRORECORDINGDBBVIDEOOPTIMALJAZZROCKTECHNODSCDISC 2DISC 1RECORDDUBBING A.REPLAY DIGITAL SOUND CONTROLVOLUMECLOCKTIMERMICROPHONE - LEVEL0OPENTAPE2TAPE1OPENDEMO STOP! 0 9 1 2 3 4 5 6 7 8 # $ % when the sys

6、tem is in standby ordemonstration mode.If the PLUG and PLAY has not been installedbefore, you can access this feature by switchingon the system from the main power outlet.“AUTO INSTALL- PRESS PLAY” will bedisplayed.2PressPLAY to start installation.“INSTALL” will be displayed and followed by“TUNER” a

7、nd then “AUTO“.ThePROGRAMstarts flashing.PLUG and PLAY will start searching for allradio stations on FM band and then followed byradio stations on MW band.All available radio stations with sufficient signalstrength will be stored.Up to 40 presets may bestored. The last preset radio station will appe

8、ar onthe display when PLUG and PLAY is completed.Toexit without storing the PLUG and PLAY,pressbutton(on the system only).Notes: PLUG and PLAY will be reinitiated again duringthe next power up if :i) PLUG and PLAY installation was notcompleted. ii) No stereo frequency being detected duringPLUG and P

9、LAY, “CHECK ANTENNA“ will bedisplayed.You can store any radio stations manually orautomatically after PLUG and PLAY.When PLUG and PLAY is used,all previouslystored radio stations will be replaced.During PLUG and PLAY, if no button is pressedwithin 15 seconds, the system will go todemonstration mode

10、(if demonstration mode isenable) Demonstration mode The system has a demonstration mode thatshows the various features offered by the system.Todisable the demonstration modePress and hold (on the system only)for 5secondswhen the system is in demonstrationmode.“DEMO OFF“ is displayed.The system will

11、switch to standby mode.2213TUNERTAPE 1/2CDSLEEPAUXDIMDSCDBBMUTEREPEATPAUSESHUFFLECD DIRECTVOLUME 12EnglishToenable the demonstration modePress and hold (on the system only)for 5secondswhen the system is in standby mode.The demonstration will begin.Notes: If the demonstration mode has not been disabl

12、ed,it will resume 5 seconds later after the systemswitches to standby mode.When the system is switched on from the mainpower outlet,the CD changer tray may open andclose again to initialize the set.Even though the AC power cord is removed fromand reconnected to the wall socket,thedemonstration will

13、remain off until it is switched onagain. Switching the system ONPressCD,TUNER,TAPEor AUX.PressSTANDBY-ON in demo.You can also switch on the system by pressingany one of the CD DIRECT PLAY buttons (onsystem only).Switching the system to standbymodePressSTANDBY-ONor Bon the remotecontrol. The system w

14、ill switch to standby mode.Selecting the SourcePress the respective source selection button:CD,TUNER,TAPEor AUX.The display indicates the selected source.Note: For an external source, make sure you haveconnected the audio left and right OUT terminalsof the external equipment (TV, VCR,Laser Discplaye

15、r, DVD player or CD Recorder) to the AUX INterminals.DIM mode You can select the desired brightness for thedisplay.PressDIMto select DIM 1, DIM 2, DIM 3 orDIM OFF display mode.TheDIMdisplay lights up.“DIM 1“, “DIM 2“, “DIM 3“ or “DIM OFF“will be displayed depending on the modeselected. DIM OFF - normal brightness with Spectrum Analyzer OnDIM 1 - normal brightness with Spectrum Analyzer OffDIM 2 - half brightness with Spectrum Analyzer OnDIM 3 - half brightness with Spectrum Analyzer Off and all LEDs on the systemwill be switched off.Operating the System