Yamaha-RXV-863-Service-Manual电路原理图.pdf
《Yamaha-RXV-863-Service-Manual电路原理图.pdf》由会员分享,可在线阅读,更多相关《Yamaha-RXV-863-Service-Manual电路原理图.pdf(155页珍藏版)》请在收音机爱好者资料库上搜索。
1、SERVICE MANUAL 101088 IMPORTANT NOTICE This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the user
2、s, and have therefore not been restated. WARNING:Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA pro
3、duct owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT:The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical
4、capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications ar
5、e, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributors Service Division. WARNING:Static discharges can destroy expensive components. Discharge any static electricity your body
6、 may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT:Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit. CONTENTS TO SERVICE PERSONNEL . 2 FRONT PANELS. 35 REAR
7、 PANELS . 610 REMOTE CONTROL PANELS. 11 SPECIFICATIONS / 参考仕様 . 1215 INTERNAL VIEW . 16 DISASSEMBLY PROCEDURES / 分解手順. 1621 UPDATING FIRMWARE / 書込 . 2236 SELF DIAGNOSIS FUNCTION (DIAG) / 自己診断機能() . 3763 CONFIRMATION OF IDLING CURRENT OF AMP UNIT / 電流確認 . 64 DISPLAY DATA . 65 IC DATA . 6682 PIN CONNE
8、CTION DIAGRAMS. 8386 BLOCK DIAGRAMS . 8791 PRINTED CIRCUIT BOARDS. 92105 SCHEMATIC DIAGRAMS. 107117 REPLACEMENT PARTS LIST . 119147 REMOTE CONTROL. 148151 ADVANCED SETUP / 本機設定変更. 152154 Using Bluetooth components / Bluetooth機器再生 . 155 P.O.Box 1, Hamamatsu, Japan 2008 All rights reserved. This manua
9、l is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically without permission. 08.03 AV RECEIVER/AV AMPLIFIER RX-V863/HTR-6180/ DSP-AX863SE/DSP-AX863 RX-V863/HTR-6180/ DSP-AX863SE/DSP-AX863 RX-V863/HTR-6180/DSP-AX863SE/DSP-AX863 2 RX-V863/HTR-6180/ DSP-AX863S
10、E/DSP-AX863 WALL OUTLET EQUIPMENT UNDER TEST AC LEAKAGE TESTER OR EQUIVALENT INSULATING TABLE 1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measur
11、ement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohms shunted by 0.15F. For U model “CAUTION” “F2501, F2502: FOR CONTINUED PROTECTION
12、 AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 125V FUSE.” For C model CAUTION F2501, F2502: REPLACE WITH SAME TYPE 10A, 125V FUSE. ATTENTION F2501, F2502: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 10A, 125V. Leakage current must not exceed 0.5mA. Be sure to test for leakage with the A
13、C plug in both polarities. 本機搭載基板付接合 部無鉛付。 無鉛種類、修理時下記 無鉛使用推奨。 Sn+Ag+Cu (錫+銀+銅) Sn+Cu (錫+銅) Sn+Zn+Bi (錫+亜鉛+) 注意: 無鉛融点温度通常鉛入比3040 程度高、合 使用。 All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder. Among some types of lead free solder currently available, it
14、is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Caution: As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder
15、, be sure to use a soldering iron suitable to each solder. About lead free solder / 無鉛 TO SERVICE PERSONNEL WARNING: CHEMICAL CONTENT NOTICE! This product contains chemicals known to the State of California to cause cancer, or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL
16、/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHAT SO EVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosur
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Yamaha RXV 863 Service Manual 电路 原理图
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


