AltecLansing-1568A-pwr-sch2维修电路原理图.pdf

《AltecLansing-1568A-pwr-sch2维修电路原理图.pdf》由会员分享，可在线阅读，更多相关《AltecLansing-1568A-pwr-sch2维修电路原理图.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、OPERATING INSTRUCTIONS SPECIFICATIONS Type: Gain: Input Sensitivity: Power Output: Frequency Response: Input Impedance: Source Impedance: Load Impedance: Output Impedance: Noise Level: Controls: Power Supply: External Power Available: Tubes: Dimensions: Color: Weight: Special Feature: Accessory: Pow

2、er Amplifier 65 db 0.9 volt 40 watts at less than 2% thd 40 to 20,000 cps 1 db, 5-30,000 cps; 4 db, 1-100,000 cps 70,000 ohm potentiometer 150 or 600 ohms with 15095 Plug-in Transformer 4 (12.6 v), 8 (18 v), 16 (25 v), 124 (70 v) ohms ungrounded Less than 15% of nominal load impedance 80 db below ra

3、ted output Volume control, continuously variable, composition 117 vac, 50/60 cycles, 125 watts 117 volt ac receptacle on chassis 2-6CG7, 2-6CA7/EL34, 1-5U4GB 8 3/4 high, 19 wide, 7 3/4 deep Dark green 22 lbs. Two stage high-pass-filter for protection of horn loaded drivers 15095 Plug-in Transformer

4、RadioFans.CN 收音机爱 好者资料库GENERAL DESCRIPTION The 1568A Amplifier is a rack mounted, AC operated power amplifier intended for use in sound reinforcing, paging, music distribution, or any application requiring low distortion, wide frequency range, complete stability with any type of load, reliability of

5、 operation, ease of servicing or low cost. At 40 watts distortion is less than 2% at any frequency from 40 to 20,000 cycles per second. The frequency response is within 4 db of mid range value from 1 cycle per second to 100 KC. The feedback circuit is designed for stability under conditions of varyi

6、ng line voltage, varying tube characteristics, and all types of loads including long unloaded speaker lines having considerable capacitance. The tubes are conservatively operated under CCS (con-tinuous commercial service) ratings of their manufacturer, and the amplifier has been shown to withstand h

7、ot switching and other punishment which might be encountered in the hands of untrained operators. The amplifier occupies five units of rack space (8 3/4) and has a hinged front panel on which are mounted the power switch, fuse, pilot light and a continuously variable gain control. All circuitry is c

8、ompletely acces-sible for servicing when the front panel is open. The amplifier is equipped with a 3-wire power cord terminating in a 3-pin cap. Input and output terminals are provided in the form of barrier-type terminal blocks mounted on the outer surface of the chassis. INPUT CONNECTIONS The 1568

9、A Amplifier is equipped with two pairs of input connections. Terminals 1 and 2, connecting directly to the input potentiometer, are provided for unbalanced high impedance sources, and to bridge unbalanced low impedance lines having a signal voltage of 0.9 volt or higher. Terminals 3 and 4 connect to

10、 a standard octal socket which accommodates the accessory plug-in transformer. With the 15095 Transformer, balanced or unbalanced lines of 150 or 600 ohms up to a level of +15 dbm may be connected to input 3-4. The octal socket is normally connected for 500/600 ohm operation; 150 ohms impedance may

11、be obtained by strapping the terminals in accordance with the diagram shown on the schematic. OUTPUT CONNECTIONS Outputs accommodate nominal loads of 4, 8, 16 and 1 24 ohms, the corresponding full-drive output voltages being 12.6, 18, 25 and 70 volts. Speaker Matching: Use the output tap which most

12、nearly equals the total speaker impedance. If the load im-pedance falls between two output terminal values, favor the terminal of lower impedance. 70 Volt Line: The 70 volt distribution system permits connection to a large number of speakers, each to operate at its own power level as required, witho

13、ut the necessity for computing impedances. In this system each speaker is equipped with a transformer containing a number of taps rated in terms of power, and the tap is selected which gives the power desired for that speaker. The total of the power settings for all speakers should be equal to or le

14、ss than the amplifier system power rating. The 1568A Amplifier is equipped with outputs to drive both a 70 volt line and a 25 volt line. Protection of Horn Loaded Drivers: Driver loudspeakers coupled to horns are used in paging or voice reinforcing systems where excellent intelligibility is required

15、 in the presence of high noise levels, effects of wind, and other disturbances. When a loudspeaker system dividing network is not available the diaphragm of the driver loud-speaker may be protected from low frequency power by the use of the R-C low frequency cut-off filter in V1 grid circuit (see sc

16、hematic). As shipped, capacitors C1 and C2 are strapped out. By cutting one or both of these straps attenuation is introduced as shown in the table, depending upon the impedance of the source. Effect of High Pass Filter Source Strapping 250 500 1000 2000 cps Impedance 100,00 ohms One strap cut - 6.5

17、 - 3 -1 -0.2 db Both straps cut -16 - 8 -3.5 -1.2 db Low One strap cut -13 - 8 -3.5 -1.2 db Both straps cut -22 -12 -4.2 -1.5 db CONTROLS The only controls on this amplifier intended for normal operation are the power switch and the gain control. Potentiometer P2, which establishes the bias voltage

18、for the output tubes, is set at the factory and will probably not require readjustment over a long period of operation. If, due to ageing of the rectifier, the bias voltage should drop below the value indicated on the schematic, it will be desirable to reset P2. Measurement should be made with an ac

19、curate voltmeter, at a line voltage of 117 volts, and with no signal applied. RadioFans.CN 收音机爱 好者资料库 FREQUENCY IN CYCLES PER SECOND PARTS LIST C1 .002 mfd. 10% ceramic disc Erie 811-202 C2 .001 mfd. 10% ceramic disc Erie 811-202 C3 50 mfd. 6 V. MalloryTT C4 .000047 mfd. 10% ceramic disc Erie 831-47

20、0 C6, 7 .22 mfd. 400 V. Sprague 4TMP-22 C8 50 mfd. 50 V. MalloryTC C9, 10 40 x 40 mfd. 500 V. Mallory FP288 C11 .5 mfd. 400 V. CD PJ4P5 R1, 8, 12, 13 100,000 ohms 10% 1/2 watt R2 47 ohms 1% 1/2 watt deposited carbon R3 1800 ohms 10% 1/2 watt R4 100,000 ohms 10% 1 watt R5, 6 68,000 ohms 10% 1/2 watt

21、R7 1 megohm 10% 1/2 watt R9 18,000 ohms 10% 1 watt R10, 11, 18 47,000 ohms 10% 1 watt R14, 15 R16 R17 R20 R19 P1 P2 F1 PL1 S1 SR1 J1 T1 T2 V1, 2 V3, 4 V5 100 ohms 10% 1/2 watt 600 ohms 5 watt Ohmite Brown Devil 1500 ohms 1 % 1/2 watt deposited carbon 220 ohms 10% 1/2 watt 4700 ohms 10% 1 watt 200,000 ohms Altec Lansing 12435 5000 ohms Mel-Rain Type FFF-1 3 amp. 3 AG fuse Mazda #44 Altec Lansing 12536 switch Selenium Rectifier GE1N1491 Alden 402 ACEHG receptacle Peerless 16432 Peerless 6288 6CG7 vacuum tube 6CA7/EL34 vacuum tube 5U4GB vacuum tube RadioFans.CN 收音机爱 好者资料库RadioFans.CN 收音机爱 好者资料库