Aiwa Cd Stereo Cassette Receiver Nsx-Aj14-Bl14E-Bl14-Bl16 Parts & Service 电路图.pdf

《Aiwa Cd Stereo Cassette Receiver Nsx-Aj14-Bl14E-Bl14-Bl16 Parts & Service 电路图.pdf》由会员分享，可在线阅读，更多相关《Aiwa Cd Stereo Cassette Receiver Nsx-Aj14-Bl14E-Bl14-Bl16 Parts & Service 电路图.pdf（47页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL COMPACT DISC STEREO CASSETTE RECEIVER BASIC TAPE MECHANISM : ZZM-2 PR1NM BASIC CD MECHANISM : AZG-1 ZA3RNDM NSX-AJ14 NSX-BL14E NSX-BL14 NSX-BL16 U HA HS, EZ, K EZ S/M Code No. 09-004-428-8R2 REVISION If requiring information about the CD mechanism, see Service Manual of AZG-1 (S/M Cod

2、e No. 09-001-335-3NC). This Service Manual is the “Revision Publishing” and replaces “Simple Manual” NSX-AJ14(U)/BL14E(HA)/BL14(HS,EZ,K)/BL16(EZ), (S/M Code No. 09-003-428-8T2). DATA NSX-AJ14 SPEAKER SYSTEM CD CASSEIVER REMOTE CONTROLLER NSX-BL14 NSX-BL16 CX-NAJ14SX-NAJ11 CX-NBL14 SX-NBL11 SX-NBL16

3、RC-ZAS02 NSX-BL14ECX-NBL14ESX-NBL17 RadioFans.CN 收音机爱 好者资料库 2 Tuning range87.5 MHz to 108 MHz Usable sensitivity (IHF)U,HA,HS: 13.2 dBf EZ,K: 16.8 dBf Antenna terminals75 ohms (unbalanced) Tuning range530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) Usable sensitivity350 V/m Antenn

4、aLoop antenna Tuning range144 kHz to 290 kHz Usable sensitivity1400 V/m AntennaLoop antenna Power outputRated U: 10 W + 10 W (50 Hz - 20 kHz, T.H.D. less than 1%, 6 ohms) 15 W + 15 W (1 kHz, T.H.D. less than 10%, 6 ohms) HA: 28 W + 28 W (1 kHz, T.H.D. 1%, 6 ohms) Reference: 35 W + 35 W (1 kHz, T.H.D

5、. 10%, 6 ohms) HS: 17 W + 17 W (1 kHz, T.H.D. 1%, 6 ohms) Reference: 20 W + 20 W (1 kHz, T.H.D. 10%, 6 ohms) EZ,K: 12 W + 12 W (1 kHz/DIN 45500, T.H.D. 1%, 6 ohms) Reference: 15 W + 15 W (1 kHz/DIN 45324, T.H.D. 10%, 6 ohms) EZ:DIN MUSIC POWER: 30 W + 30 W Total harmonic distortion U,EZ,K: 0.1% (6 W

6、, 1 kHz, 6 ohms, DIN AUDIO) HA: 0.1% (14 W, 1 kHz, 6 ohms, DIN AUDIO) HS: 0.1% (8 W, 1 kHz, 6 ohms, DIN AUDIO) InputsVIDEO/AUX: 500 mV HS: MIC 1.8 mV(10 kohms) OutputsSPEAKERS: accept speakers of 6 ohms or more PHONES (stereo jack) : accepts headphones of 32 ohms or more Track format4 tracks, 2 chan

7、nels stereo Frequency response50 Hz - 8000 Hz Recording systemAC bias HeadsDeck 1 : Recording/Playback head x 1, erase head x 1 Deck 2 : Playback head x 1 LaserSemiconductor laser ( =780 nm) D-A converter1 bit dual Signal-to-noise ratio85 dB (1 kHz, 0 dB) Harmonic distortion0.05 % (1 kHz, 0 dB) SX-N

8、AJ11 Speaker System2 way, bass reflex (magnetic shielded type) Speaker unitsWoofer: 120 mm (43/4 in.) cone type Tweeter: 20 mm (13/16 in.) cone type Impedance6 ohms Sensitivity87 dB/W/m Dimensions (W x H x D)220 x 324 x 211 mm (83/4 x 127/8 x 83/8 in.) Weight2.0 kg (4 lbs 7 oz.) SPECIFICATIONS SX-NB

9、L17,SX-NBL11, SX-NBL16 Speaker System2 way, bass reflex (magnetic shielded type) Speaker unitsWoofer: 120 mm cone type Tweeter: 20 mm cone type Impedance6 ohms Sensitivity87 dB/W/m Dimensions (W x H x D)220 x 324 x 211 mm Weight2.0 kg Power requirementsU: 120 V AC, 60 Hz HA: 120 V/220-230 V/240 V AC

10、 (switchable), 50/60 Hz HS: 220 V AC, 60 Hz EZ,K: 230 V AC, 50 Hz Power consumptionU: 38 W HA: 55 W HS: 60 W EZ,K: 45 W Power consumptionU: With power-economizing in standby modemode off : 8 W HA: With power-economizing mode off : 12 W HS,EZ,K: With power-economizing mode off : 14 W With power-econo

11、mizing mode on : 0.9 W Dimensions of main unitU,EZ,K: (W x H x D)260 x 324 x 348 mm (101/4 x 127/8 x 133/4 in.) HA,HS: 260 x 324 x 348 mm Weight of main unitU: 4.8 kg (10 lbs 9 oz.) HA: 5.7 kg HS: 5.0 kg EZ,K: 4.9 kg Design and specifications are subject to change without notice. RadioFans.CN 收音机爱 好

12、者资料库 3 CLASS 1LASER PRODUCT KLASSE 1LASER PRODUKT LUOKAN 1LASER LAITE KLASS 1LASER APPARAT This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY T

13、O CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJEC- TIVE LENS ON THE OPTICAL PICK-UP BLOCK. sCaution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. sAdvarsel: Usynlig laserstling ved bning, nr sikker

14、hedsafbrydere er ude af funktion. Undg udsttelse for strling. VAROITUS! Laiteen Kyttminen muulla kuin tss kyttohjeessa mainitulla tavalla saattaa altistaa kyt-tjn turvallisuusluokan 1 ylittvlle nkymttmlle lasersteilylle. VARNING! Om apparaten anvnds p annat stt n vad som specificeras i denna bruksan

15、vising, kan anvndaren utsttas fr osynling laserstrlning, som verskrider grnsen fr laserklass 1. PROTECTION OF EYES FROM LASER BEAM DURING SERVICING CAUTION Use of controls or adjustments or performance of proce- dures other than those specified herein may result in hazardous radiation exposure. ATTE

16、NTION Lutillisation de commandes, rglages ou procdures autres que ceux spcifis peut entraner une dangereuse exposition aux radiations. ADVARSEL Usynlig laserstling ved bning, nr sikkerhedsafbrydereer ude af funktion. Undg udsttelse for strling. This Compact Disc player is classified as a CLASS 1 LAS

17、ER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. PICK-UP ASSY P.C.B Precaution to replace Optical block (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch

18、 the diode. 1) After the connection, remove solder shown in right figure. SOLDER RadioFans.CN 收音机爱 好者资料库 4 NOTE ON BEFORE STARTING REPAIR Charging voltage (V)Discharging Rated power (W)Parts number (C101, 102)resistor () 25-48100387-A00-247-090 49-140220587-A00-232-090 Note: The reference numbers (C

19、101, C102) of the electrolytic capacitors can change depending on the models. Be sure to check the reference numbers of the charging capacitors on schematic diagram before starting the discharging work. 2. Check items before exchanging the MICROCOMPUTER Be sure to check the following items before ex

20、changing the MICROCOMPUTER. Exchange the MICROCOMPUTER after confirming that the MICROCOMPUTER is surely defective. 2-1. Regarding the HOLD terminal of the MICROCOMPUTER When the HOLD terminal (INPUT) of the MICROCOMPUTER is “H”, the MICROCOMPUTER is judged to be operating correctly. When this termi

21、nal is “L”, the main power cannot be turned on. Therefore, be sure to check the terminal voltage of the HOLD terminal before exchange. When the MICROCOMPUTER is not defective, the HOLD terminal can also go “L” when the POWER AMPLIFIER has any abnormalities that triggers the abnormality detection cir

22、cuit on the MAIN C. B. that sets the HOLD terminal to “L”. Good or no good judgement of the MICROCOMPUTER 11111Turn on the AC main power. 22222Confirm that the main power is turned on and the HOLD terminal of the MICROCOMPUTER keeps the “H” level or not. 33333When the HOLD terminal is “L” level, the

23、 abnormality detection circuit is judged to be working correctly and the MICROCOMPUTER is judged to be good. 1. Forced discharge of electrolytic capacitor of power supply block When repair is going to be attempted in the set that uses relay circuit in the power supply block, electric potential is ke

24、pt charged across the electrolytic capacitors (C101, 102) even though AC power cord is removed. If repair is attempted in this condition, secondary defect can occur. In order to prevent the secondary trouble, perform the following measures before starting repair work. Discharge procedure 11111Remove

25、 the AC power cord. 22222Connect a discharging resistor at an end of lead wire that has clips at both ends. Connect the other end of the lead wire to metal chassis. 33333Contact the other end of the discharging resistor to the positive (+) side (+VH) of C101. (For two seconds) 44444Contact the same

26、end of the discharging resistor as step 33333 to the negative (-) side (-VH) of C102 in the same way. (For two seconds) 55555Check that voltage across C101 and C102 has decreased to 1 V or less using a multimeter or an oscilloscope. Select a discharging resistor referring to the following table.Fig-

27、1 MAIN C.B D101 C101C102 22 34 5 In such a case, check also if the POWER AMPLIFIER circuit or power supply circuit has any abnormalities or not. 2-2. Regarding reset There are cases that the machine does not work correctly because the MICROCOMPUTER is not reset even though the AC power cord is re-in

28、serted, or the software reset (pressing the STOP key + POWER key) is performed. When the above described phenomenon occurs, it can lead to wrong judgement as if the MICROCOMPUTER is defective and to exchange the MICROCOMPUTER. In such a case, perform the forced-reset by the following procedure and c

29、heck good or no good of the MICROCOMPUTER. 11111Remove the AC power cord. 22222Short both ends of the electrolytic capacitor C113 that is connected to VDD of the MICROCOMPUTER with tweezers. 33333Connect the AC power cord again. If the MICROCOMPUTER returns to the normal operation, the MICROCOMPUTER

30、 is good. Note: The reference number or MICROCOMPUTER pin number of transistor (Q110) and electrolytic capacitor (C113) can change depending on the models. Be sure to check the reference numbers on schematic diagram before starting the discharging work. 2-3. Confirmation of soldering state of MICROC

31、OMPUTER Check the soldering state of the MICROCOMPUTER in addition to the above described procedures. Be sure to exchange the MICROCOMPUTER after surely confirming that the trouble is not caused by poor soldering but the MICROCOMPUTER itself. Fig-2-2 MICRO- COMPUTER MICROCOMPUTER FRONT C.B FRONT C.B

32、 VSS VDD C113 * % C113 18 15 Short with tweezers. ELECTRICAL MAIN PARTS LIST DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. IC 8A-NFA-616-010 C-IC,M38B59MFH-E251FP 8A-NFA-615-010 C-IC,M38B57MCH-E236FP 87-A21-397-010 IC,STK490-070 87-A21-419-040 C-IC,NJM14558MD-TE2 87-A21-

33、443-040 C-IC,M62495AFP 87-A21-415-010 IC,LA1843 87-A21-560-010 IC,LA1844L-A 87-070-127-110 IC,LC72131 D 87-A21-629-010 IC,SPS-442-10N 87-A21-482-010 IC,RPM6938-H4 87-A20-440-010 C-IC,BU1920FS TRANSISTOR 87-026-609-080 TR,KTA1266GR 89-213-702-010 TR,2SB1370 (1.8W) 87-026-610-080 TR,KTC3198GR 87-A30-0

34、76-080 C-TR,2SC3052F 87-A30-075-080 C-TR,2SA1235F 87-A30-255-010 C-TR,2SB1342 87-A30-256-010 TR,2SD1933 87-A30-190-080 TR,CC5551 87-026-245-080 TR,DTC114ES 87-A30-198-080 TR,KTC3199GR 87-A30-090-080 FET,2SK2541 87-A30-484-080 C-TR,KRA102S 87-A30-468-080 C-TR,KRC102S-RTK 87-A30-107-070 C-TR,CMBT5401

35、87-A30-106-040 C-TR,CMBT5551 87-A30-091-080 FET,2SJ460 87-A30-062-080 C-TR,KRC104S 87-A30-318-080 TR,CSA952K 89-333-317-880 TR,2SC3331 (0.5W) 87-A30-234-080 TR,CSC4115BC 89-327-143-080 TR,2SC2714 (0.1W) 87-A30-489-080 C-TR,KRA107S 89-503-602-080 C-FET,2SK360E 87-A30-086-070 C-TR,CSD1306E 87-A30-495-

36、080 TR,2SA1981Y DIODE 87-A40-736-080 DIODE,1N4148M (SEM) 87-020-465-080 DIODE,1SS133 (110MA) 87-A40-455-080 DIODE,RL203 GW 87-A40-553-080 DIODE,1N4003 LES 87-A40-774-080 ZENER,UZ24BSD 87-A40-764-080 ZENER,UZ10BSC 87-A40-313-080 C-DIODE,MC 2840 87-A40-270-080 C-DIODE,MC2838 87-A40-269-080 C-DIODE,MC2

37、836 87-A40-768-080 ZENER,UZ16BSA 87-A40-752-080 ZENER,UZ6.2BSC 87-A40-739-080 ZENER,UZ2.7BSA 87-017-149-080 ZENER,HZS6A2L 87-A40-535-080 DIODE,1N5393-GOODARK MAIN C.B C3 87-010-196-080 CHIP CAPACITOR,0.1-25 C4 87-010-196-080 CHIP CAPACITOR,0.1-25 C5 87-010-196-080 CHIP CAPACITOR,0.1-25 C6 87-010-196

38、-080 CHIP CAPACITOR,0.1-25 C9 87-010-196-080 CHIP CAPACITOR,0.1-25 C10 87-010-196-080 CHIP CAPACITOR,0.1-25 C11 87-010-196-080 CHIP CAPACITOR,0.1-25 C12 87-010-196-080 CHIP CAPACITOR,0.1-25 C19 87-A10-627-000 CAP,E 2200-50 M SMG C20 87-A10-627-000 CAP,E 2200-50 M SMG C21 87-016-495-000 CAP,E 3300-25

39、 M SMG C21 87-A10-520-000 CAP,E 3300-35 M SMG C22 87-016-495-000 CAP,E 3300-25 M SMG C22 87-016-051-000 CAP,E 2200-35 SMG C22 87-A10-011-090 CAP,E 2200-25 SMG C25 87-010-385-080 CAP, ELECT 220-25V C25 87-010-406-080 CAP, ELECT 22-50 M 11L SME C25 87-010-407-080 CAP, ELECT 33-50 M 11L SME C26 87-010-

40、247-080 CAP, ELECT 100-50V C26 87-010-406-080 CAP, ELECT 22-50 C30 87-010-247-080 CAP, ELECT 100-50V C30 87-010-384-080 CAP, ELECT 100-25M11LSME C31 87-010-263-080 CAP, ELECT 100-10V C32 87-010-197-080 CAP, CHIP 0.01 DM C33 87-010-263-080 CAP, ELECT 100-10V C34 87-010-247-080 CAP, ELECT 100-50V C35

41、87-010-406-080 CAP, ELECT 22-50 C36 87-010-381-080 CAP, ELECT 330-16V C38 87-A11-567-080 C-CAP,S 0.01-50 K B C38 87-010-190-080 C-CAP,S 0.01-50 ZF C50 87-010-384-080 CAP, ELECT 100-25 M 11L SME C60 87-010-403-080 CAP, ELECT 3.3-50V C97 87-010-196-080 CHIP CAPACITOR,0.1-25 C100 87-018-127-080 CAP TC-

42、U 470P C101 87-010-183-080 C-CAP,S 2700P-50 B C101 87-010-185-080 C-CAP,S 3900P-50 KB C102 87-010-183-080 C-CAP,S 2700P-50 B C102 87-010-185-080 C-CAP,S 3900P-50 KB C103 87-010-545-080 CAP, ELECT 0.22-50V C104 87-010-545-080 CAP, ELECT 0.22-50V C105 87-010-178-080 CHIP CAP 1000P C105 87-010-186-080

43、CAP,CHIP 4700P C106 87-010-178-080 CHIP CAP 1000P C106 87-010-186-080 CAP,CHIP 4700P C107 87-010-404-080 CAP, ELECT 4.7-50V C107 87-010-403-080 CAP, ELECT 3.3-50V C108 87-010-404-080 CAP, ELECT 4.7-50V C108 87-010-403-080 CAP, ELECT 3.3-50V C109 87-010-322-080 C-CAP, S 100P-50JCH C109 87-010-179-080

44、 C-CAP, S 1200P-50KB C110 87-010-322-080 C-CAP, S 100P-50JCH C110 87-010-179-080 C-CAP, S 1200P-50KB C111 87-010-391-080 CAP,E 10-35 SME C111 87-010-406-080 CAP, ELECT 22-50 C112 87-010-391-080 CAP,E 10-35 SME C112 87-010-406-080 CAP, ELECT 22-50 C113 87-010-405-080 CAP, ELECT 10-50V C113 87-012-156

45、-080 C-CAP, S 220P-50 J CH C113 87-A10-946-080 C-CAP, S 220P-100 J CH C114 87-010-405-080 CAP, ELECT 10-50V C114 87-012-156-080 C-CAP, S 220P-50 J CH C114 87-A10-946-080 C-CAP, S 220P-100 J CH C119 87-010-197-080 CAP, CHIP 0.01 DM C120 87-010-197-080 CAP, CHIP 0.01 DM C123 87-010-197-080 CAP, CHIP 0

46、.01 DM C124 87-010-197-080 CAP, CHIP 0.01 DM C125 87-012-368-080 C-CAP,S 0.1-50 F C125 87-010-196-080 CHIP CAPACITOR,0.1-25 C126 87-012-368-080 C-CAP,S 0.1-50 F C126 87-010-196-080 CHIP CAPACITOR,0.1-25 C127 87-012-368-080 C-CAP,S 0.1-50 F C127 87-010-196-080 CHIP CAPACITOR,0.1-25 C128 87-012-368-08

47、0 C-CAP,S 0.1-50 F C128 87-010-196-080 CHIP CAPACITOR,0.1-25 C129 87-A11-572-080 C-CAP,S 0.015-50 K B C130 87-A11-572-080 C-CAP,S 0.015-50 K B C131 87-010-197-080 CAP, CHIP 0.01 DM C132 87-010-197-080 CAP, CHIP 0.01 DM C133 87-010-186-080 CAP,CHIP 4700P C140 87-010-182-080 C-CAP,S 2200P-50 B 6 DESCRIPTIONREF. NO.KANRI NO. PART NO.DESCRIPTIONREF. NO.KANRI NO. PART NO. C183 87-010-387-080 CAP,E 470-25 SME C184 87-010-403-080 CAP, ELECT 3.3-50V C185 87-018-209-080 CAP, TC U 0.1-50ZF C200 87-018-195-080 CAP TC-U 1200P C300 87-018-195-080 CAP TC-U 1200P C301 87-010-179-080 CAP,CHI