Infinity-KappaOne caramp 电路图.pdf
《Infinity-KappaOne caramp 电路图.pdf》由会员分享,可在线阅读,更多相关《Infinity-KappaOne caramp 电路图.pdf(26页珍藏版)》请在收音机爱好者资料库上搜索。
1、 Kappa One Kappa One 1 CHANNEL POWER AMPLIFIER SERVICE MANUAL Infinity Systems Incorporated 250 Crossways Park Dr. Woodbury, New York 11797 Rev0 11/2008 Released 2008 Discontinued XXXX RadioFans.CN 收音机爱 好者资料库 - CONTENTS - SPECIFICATIONS .1 PACKING.2 CONTROL/INSTALLATION INSTRUCTIONS.3 CONTROL/INSTAL
2、LATION DRAWINGS.4 BASIC TROUBLESHOOTING5 DISASSEMBLY INSTRUCTIONS.6 EXPLODED VIEW/PARTS LIST.7 AMPLIFIER BLOCK DIAGRAM.8 ELECTRICAL PARTS LIST .9 P.C.B. DRAWINGS.14 IC/TRANSISTOR PINOUTS.20 SCHEMATICS.23 Kappa One Specifications Output Power: 500W RMS x 1 channels 4 ohms; 1% THD + N (14.4V supply) 8
3、00W RMS x 1 channels 2 ohms; 1% THD + N Total Peak Power 1600W Signal-to-noise ratio: 85dBA (reference 1W into 4 ohms) 109dBA (reference rated power into 4 ohms) Frequency response: 20Hz 320Hz (3dB) THD+N 1KHz LPF=22KHz 0.05% (rated power 4 ohms) Input Impedance 20K ohms Maximum input signal: 6.0V M
4、aximum sensitivity: 200mV Bass Boost 20-100Hz 0-12dB DC Offset 30mV Idle Current 4 ohms 1.6A Max Current Draw 76A Remote Operating Voltages OFF 4V Circuit Protection Temperature (80C), Short circuit, over/under voltage Operating voltage range (8-16V) Dimensions: 13 x 7 x 1 ” (329 x 179 x 44mm) Fuses
5、: (3) x 40A Infinity Systems continually strives to update and improve existing products, as well as create new ones. The specifications and details in this and related JBL publications are therefore subject to change without notice. KAPPA ONE 1 RadioFans.CN 收音机爱 好者资料库 KAPPA ONE 2 RadioFans.CN 收音机爱
6、好者资料库 Installation Warnings and Tips Disconnect the negative () lead from your vehicles battery. Attheinstallationsites,locateandmakeanoteofallfuel lines, hydraulic brake lines, vacuum lines and electrical wiring. Use extreme caution when cutting or drilling in and around these areas. Chooseasafemou
7、ntinglocationawayfrommoisture. Makesurethereissufficientaircirculationatthemount- ing location for the amplifier to cool itself. Mounttheamplifier,usingthesuppliedhardware. Specifications CEA-2006A-compliant 0 Speaker Output Connectors Connectthespeakerstotheseterminals,observing proper polarity. Go
8、ld screws indicate +, and silver screws indicate . Minimumspeakerimpedanceis2ohms. 1 Fuses Replaceonlywiththesametypeandrating. 2 Power Input Connectors +12V:Connecttothepositiveterminalofthevehicles battery. Install an appropriate fuse holder and fuse (120Aminimum)within18”(457mm)ofthebattery. Make
9、surethewireisnotdamagedorpinchedduring installation. Install protective grommets when routing wires through the firewall or other sheet metal. GND:Connecttothevehicleschassis.Refertothe illustration below. REM:Connecttothe“RemoteOut”leadfromthe source unit or to a source of switched +12V(ACC). 4 AWG
10、 Adapter Forpowerwirelongerthan4(1.2m),4AWGwireis recommended. Use the adapter to make the connection according to the illustration below. 3 DBO: Variable Subsonic High-Pass Filter With Variable Boost (Q) Forwoofersintuned(vented)enclosures,setthe frequency control to a value 10Hz below the enclo- s
11、ures resonance (tuned) frequency. Forwoofersinsealedboxes,setthecontroltoany value you prefer between 30Hz and 50Hz. SettheBoostcontrolaccordingtoyourpreference, being careful not to apply enough boost to damage your woofer(s). A DBOBoostcontrolprovidesupto12dBofboost, slightly above the high-pass f
12、ilters frequency. See above for appropriate settings. B DBOHigh-PassFilterFrequencycontrol,variable between 10Hz and 80Hz. See above for appropri- ate settings. 4 Crossover-Frequency Control 12dB/octavecrossover,variablefrom32Hzto320Hz. See for the adjustment procedure. Input Level Control Usedtomat
13、chtheinputleveloftheamplifierto the output level of the source unit. See A for the adjustment procedure. Input Connectors Connecttofrontoutputsfromthesourceunitor signal processor. Aux Output Connectors Nonfilteredpass-throughoutput.Connecttothe input of an additional subwoofer amplifier. Protect LE
14、D Illuminatedunderanyofthefollowingfault conditions: battery over/under voltage; short circuit in speaker wires; amplifier is too hot; amplifiers output circuit has failed (DC voltage present in the amplifiers output). Power On LEDs Illuminatedwhentheamplifierison. A Setting Input Level A TurnInputL
15、evelcontrolcounterclockwiseto6V. B With a dynamic music track playing, turn the head unitsvolumecontroltothe3/4position. C Turn Input Level control clockwise until the bass output is proportionate to the output of the high- frequency speakers, according to your preference. D Input level is now adjus
16、ted correctly. Setting the Crossover A Crossover setting for subwoofers. Note: Acceptable frequency ranges indicated in gray. Factory BoltRing Connector Ground Wire Note: Remove any paint below ring connector. Star Washer 3a ENGLISH 0058CSK - Infinity Kappa One OM Cover HIGH.indd 529/09/08 15:49:10
17、KAPPA ONE 3 A ABCD 3x4x1x 1x AB 3a ENGLISH 0058CSK - Infinity Kappa One OM Cover HIGH.indd 429/09/08 15:49:10 KAPPA ONE 4 Amplifier Troubleshooting Guide 1. Status LED on Amplifier not Lit - Head Unit (Source) Turned ON Verify: A. Remote turn-on wire from source to amplifier has proper voltage B. Po
18、wer (B+) connections at amplifier, terminal blocks, and battery are secure C. Ground (GND) connections at amplifier and vehicle chassis are secure D. Battery B+ fuse (if used) is OK E. Amplifier fuse is OK F. B+ at battery and B+ at amplifier has proper voltage 2. Status LEDs Lit, No Output from Spe
19、akers in Normal Operating Condition Verify: A. RCA cables from amplifier to source are securely connected B. Volume adjustment on amplifier is correctly adjusted C. Source is ON and playing 3. Engine Noise From Speaker(s) Turn source OFF, Disconnect RCA cables at amplifier. If noise stops, check equ
20、ipment it will be attached with a cable so unplug at Molex connector CN1 For any component repair, the entire PCB must be removed from the heatsink 5) Remove the Output end panel, four Phillips screws. 6) Remove the single remaining Phillips screw on the bottom of the heatsink 7) Remove all Phillips
21、 screws holding the Aluminum transistor clamps on 8) Slide the complete PCB out of the heatsink channel. KAPPA ONE 6 KAPPA ONE 7 1234 A B C D 4321 D C B A OP OP OP OP OPOP 11253201132050 AMP SPEAKER GAIN CONTROL BASS BOOST VARIABLE 0dB-12dB MODEL FREQ VARIABLE LP 11HZ-320HZ/12dB MAIN AMP FRONTL 2ohm
22、/4ohm AUX OUT L AUX OUT R + - Battery +VCC -VCC +5V -5V +15V -15V POWER SUPPLY 1 2 3 4 5 6 7 8 OP OP RJ45 R L 102580 MODEL FREQ VARIABLE HP 10HZ-80HZ/12dB KAPPA ONE 8 KAPPA ONE Electrical Parts List Part NumberQtyReference Designator Main PCB Resistors 0702-0106-03Resistor0.1 1% 1.5 10.5MM H16.5MM47
23、R R127 R126 R124 0701-A123-02ResistorSMD 1W 12K 5% 251261R 2R 4R 3R R177 R176 0702-3103-02Resistor 1/2W 10K 5%12.5MM1R69 0701-54R7-02ResistorSMD 4.7 1/2W 5% 25121R119 0705-5470-04Resistor 5W 47 5% 13.5*9*23MM1R142 0701-2100-03ResistorSMD 10 1/8W 1% 08056R112 R111 R110 R109 R108 R107 0712-64R7-02Resi
24、stor 2W 4.7 5% 10MM 1R139 0701-A220-02ResistorSMD 22 1W 5% 25123R168 R167 R169 0704-6221-02Resistor 2W 220 5% 1R136 0701-3220-02ResistorSMD 22 1/4W 5% 120626R 5R 0702-3331-02Resistor 1/2W 330 5%12.5MM2R67 R66 0701-2101-03ResistorSMD 100 1/8W 1% 080519 R188 R187 R166 R165 R164 R162 R161 R160 R47 R190
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- Infinity-KappaOne caramp 电路图 Infinity KappaOne
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


