Sony Cdpcx355 电路图.pdf

《Sony Cdpcx355 电路图.pdf》由会员分享，可在线阅读，更多相关《Sony Cdpcx355 电路图.pdf（72页珍藏版）》请在收音机爱好者资料库上搜索。

1、CDP-CX355 US Model Canadian Model AEP Model UK Model E Model Australian Model SERVICE MANUAL COMPACT DISC PLAYER Sony Corporation Home Audio Company Published by Sony Engineering Corporation 9-873-551-01 2002B1600-1 2002.02 SPECIFICATIONS Ver 1.0 2002. 02 Model Name Using Similar MechanismNEW CD Mec

2、hanism TypeCDM54-K1BD45 Base Unit TypeBU-K1BD45 Optical Pick-up TypeKSS-213BFN Compact disc player LaserSemiconductor laser ( = 780 nm) Emission duration: continuous Laser outputMax 44.6 W* * This output is the value measured at a distance of 200 mm from the objective lens surface on the Optical Pic

3、k-up block with 7 mm aperture. Frequency response20 Hz to 20 kHz 0.5 dB Signal-to-noise ratioMore than 107 dB Dynamic rangeMore than 86 dB Harmonic distortionLess than 0.009 % Channel separationMore than 100 dB Outputs ANALOG OUT DIGITAL OUT (OPTICAL) General Where purchased USA and Canadian Austral

4、ia Load impedance Over 10 kilohms Wave length: 660 nm Maximum output level 2 V (at 50 kilohms) 18 dBm Jack type Phono jacks Optical output connector Power consumptionsPower requirements 120 V AC, 60 Hz13 W 14 W 13 W 13 W 240 V AC, 50/60 Hz Europe and Asia230 V AC, 50/60 Hz Other countries Dimensions

5、 (approx.)430 189 493 mm (w/h/d)(17 7 1/2 19 3/8 in.) incl. projecting parts Mass (approx.)8.5 kg (18 lbs 12 oz) Supplied accessories Design and specifications are subject to change without notice. Audio cord (1) Remote commander (remote) (1) Size AA (R6) batteries (2) 120 V AC, 50/60 Hz RadioFans.C

6、N 收音机爱 好者资料库 2 This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. The following caution label is located inside the unit. Laser component in this product is capable of emitting radiation exceeding the limit for Class 1. CAUTION

7、 Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexibl

8、e Circuit Board Repairing Keep the temperature of soldering iron around 270C during repairing. Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. CDP-CX355 SAFETY-RELATED COMPONENT

9、 WARNING! COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. ATTENTION AU COMPOSANT

10、AYANT RAPPORT LA SCURIT! LES COMPOSANTS IDENTIFS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHMATIQUES ET LA LISTE DES PICES SONT CRITIQUES POUR LA SCURIT DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PISES SONY DONT LES NUMROS SONT DONNS DANS CE MANUEL OU DANS LES SUPPMENTS PUBLIS PAR SONY.

11、After correcting the original service problem, perform the following safety checks before releasing the set to the customer: Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below. LEAKAGE The AC leakage

12、 from any exposed metal part to earth ground and from all exposed metal parts to any exposed metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes). Leakage current can be measured by any one of three methods. 1.A commercial leakage tester, such as the Simpson 229 or RCA WT

13、-540A. Follow the manufacturers instructions to use these instruments. 2.A battery-operated AC milliammeter. The Data Precision 245 digital multimeter is suitable for this job. 3.Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The “limit” indication i

14、s 0.75 V, so analog meters must have an accurate low-voltage scale. The Simpson 250 and Sanwa SH-63Trd are examples of a passive VOM that is suitable. Nearly all battery operated digital multimeters that have a 2V AC range are suitable. (See Fig. A) SAFETY CHECK-OUT To Exposed Metal Parts on Set 0.1

15、5 F 1.5 k AC Voltmeter (0.75 V) Earth Ground Fig. A. Using an AC voltmeter to check AC leakage. MODEL IDENTIFICATION BACK PANEL PART NO. PARTS No.MODEL 4-238-109-0 4-238-109-1 4-238-109-2 4-238-109-3 4-238-109-4 4-238-109-5 US Canadian AEP, UK Singapore Australian E RadioFans.CN 收音机爱 好者资料库 3 CDP-CX3

16、55 TABLE OF CONTENTS SECTION 1 SERVICING NOTE NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body

17、. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repain parts. The flexible board is easily damaged and should be handled with care. NOTES ON LASER DIODE EMISSION CHECK The laser beam on this model is concentrated so

18、 as to be focused on the disc reflective surface by the objective lens in the optical pick- up block. Therefore, when checking the laser diode emission, observe from more than 30 cm away from the objective lens. The emission check enables continuous checking of the S curve. LASER DIODE AND FOCUS SEA

19、RCH OPERATION CHECK Carry out the “S curve check” in “CD section adjustment” and check that the S curve waveform is output three times. 1. SERVICING NOTE3 2. GENERAL6 3. DISASSEMBLY 7 3-1. Case 8 3-2. Bracket (F. W. ) 8 3-3. Front Panel Assy 9 3-4. DISP Board, JOG Board, KEYBOARD Board 9 3-5. LED Bo

20、ard, Guide (Door. T) 10 3-6. Table (300) Assy, Cover (P.T.) 10 3-7. D. MOTOR Board, Door Motor Assy (M83) 11 3-8. D. SW Board12 3-9. Base (Door, Gear) Assy 13 3-10. Pop-up Assy 13 3-11. D. SENS (OUT) Board 14 3-12. T. SENS Board 14 3-13. D. SENS (IN) Board 15 3-14. Back Panel Section 15 3-15. MAIN B

21、oard, JACK Board 16 3-16. POWER Board 16 3-17. Bracket (Top) , BU Assy 17 3-18. BU Holder Assy 17 3-19. BD Board, Optical Device (KSM-213 BFN) 18 3-20. L. SW (A) Board, L. SW (B) Board 19 3-21. CDM Assy 20 3-22. Motor Assy (Loading) (M82) , Motor Assy (Table) (M81) , L. T. MOTOR Board 20 4. SERVICE

22、MODE 21 5. TEST MODE 25 5-1. ADJ Mode25 5-2. Key and Display Check Mode 25 6. ADJUSTMENTS 26 6-1. Mechanical Adjustments 26 6-2. Electrical Adjustment 28 7. DIAGRAMS 31 7-1. Block Diagrams BD Section 32 MAIN Section 33 7-2. Printed Wiring Board BD Section 34 7-3. Schematic Diagram BD Section 35 7-4.

23、 Printed Wiring Board MAIN Section 36 7-5. Schematic Diagram MAIN Section (1/2) 37 7-6. Schematic Diagram MAIN Section (2/2) 38 7-7. Printed Wiring Board T.SENS Section 39 7-8. Printed Wiring Board D.SENS (IN) Section 39 7-9. Printed Wiring Board D.SENS (OUT) Section 39 7-10. Schematic Diagram SENSO

24、R Section 39 7-11. Printed Wiring Board DISPLAY Section 40 7-12. Schematic Diagram DISPLAY Section 41 7-13. Printed Wiring Board JOG Section 42 7-14. Schematic Diagram JOG Section 43 7-15. Printed Wiring Board POWER Section 44 7-16. Schematic Diagram POWER Section 44 7-17. Printed Wiring Board JACK

25、Section 45 7-18. Schematic Diagram JACK Section 45 7-19. Printed Wiring Board SWITCH/MOTOR Section 46 7-20. Schematic Diagram SWITCH/MOTOR Section 46 7-21. IC Pin Functions 50 8. EXPLODED VIEWS 54 8-1. Case Section 54 8-2. Chassis Section 1 55 8-3. Chassis Section 2 56 8-4. Back Panel Section 57 8-5

26、. Front Panel Section 58 8-6. Mechanism Section 1 (CDM54-K1BD45) (Pop-up Assy, Base (Door. Gear) Assy) 59 8-7. Mechanism Section 2 (CDM54-K1BD45) 60 8-8. Mechanism Section 3 (CDM54-K1BD45) 61 8-9. Mechanism Section 4 (CDM54-K1BD45) 62 8-10. Optical Pick-up Section (BU-K1BD45) 63 9. ELECTRICAL PARTS

27、LIST64 RadioFans.CN 收音机爱 好者资料库 4 CDP-CX355 CD-TEXT TEST DISC This unit is able to display the TEXT data (character information) written in the CD on its fluorescent indicator tube. The CD-TEXT TEST DISC (TGCS-313:J-2501-126-A) is used for checking the display. To check, perform the following procedu

28、re. Checking Method: 1.Turn ON the power, set the disc on the disc table with the side labeled as “test disc” as the right side, close the front cover, and chuck the disc. 2.The following will be displayed on the fluorescent indicator tube. (The display switches each time the TIME/TEXT button is pre

29、ssed.) Display : CD TEXT TEST DISC (Album Title) 3.Press the button and play back the disc. 4.The following will be displayed on the fluorescent indicator tube. (If nothing is displayed, press the TIME/TEXT button.) Display : 1kHz/0 dB/ L ?(38h to 3Fh) A B C D E F G(40h to 47h) H I J K L MNO(48h to

30、4Fh) P QR S T U VW(50h to 57h) X Y Z _(58h to 5Fh) a b c d e f g(60h to 57h) h i j k l m n o(68h to 6Fh) p q r s t u v w(70h to 77h) x y z I (78h to 7Fh) i (A0h to A7h) 8859-1 C PR (A8h to AFh) 23 (B0h to B7h) 1 (B8h to BFh) (C0h to C7h) (C8h to CFh) D (D0h to D7h) Y(D8h to DFh) (E0h to E7h) (E8h to

31、 FFh) (F0h to F7h) y(F8h to FFh) No.66 No.67 to No.99 1 4 1 2 3 4 1 4 1 2 3 4 Table 2: CD-TEXT TEST DISC Recorded Contents and Display (In this unit, some special characters cannot be displayed. This is no a fault.) 6 CDP-CX355 SECTION 2 GENERAL 34 5 6 7 89101112 1 2 15 16 17 18 13 14 2324252638 391

32、9 20 21 22 31 30 29 28 2736 35 34 33 32 Location of Parts and Controls 11/u (power) button 2STANDBY indicator 3Display window 4CONTINUE button 5SHUFFLE button 6PROGRAM button 7REPEAT button 8TIME/TEXT button 9Front cover 10 AMS /PUSH ENTER knob and button 11 MENU/NO button 12 +100 button 13 YES butt

33、on 14 DISC/CHARACTER/PUSH ENTER knob and button 15 EASY PLAY button and indicator 16 MEMO/SEARCH button 17 CHECK button 18 CLEAR button 19 MEGA CONTROL button and indicator 20 X-FADE button 21 NO DELAY button 22 FADER button 23 p (stop)/DISC EJECT button 24 P (pause) button and indicator 25 (play) b

34、utton and indicator 26 OPEN/CLOSE button 27 HIT LIST button and indicator 28 GROUP 4 button and indicator 29 GROUP 3 button and indicator 30 GROUP 2 button and indicator 31 GROUP 1 button and indicator 32 GROUP FILE button 33 GROUP 8 button and indicator 34 GROUP 7 button and indicator 35 GROUP 6 bu

35、tton and indicator 36 GROUP 5 button and indicator 38 KEYBOARD jack 39 TIMER OFF/PLAY switch * AMS is abbreviation for Automatic Music Sensor. 7 CDP-CX355 SECTION 3 DISASSEMBLY BRACKET (F.W.) (Page 8) SET DISP BOARD, JOG BOARD, KEYBOARD BOARD, (Page 9) FRONT PANEL ASSY (Page 9) CASE (Page 8) LED BOA

36、RD, GUIDE (DOOR.T) (Page 10) TABLE (300) ASSY, COVER (P.T.) (Page 10) D. MOTOR BOARD, DOOR MOTOR ASSY (M83) (Page 11) BACK PANEL SECTION (Page 15) BRACKET (TOP), BU ASSY (Page 17) BD BOARD OPTICAL DEVICE (KSM-213BFM) (Page 18) MOTOR ASSY (LOADING) (M82), MOTOR ASSY (TABLE) (M81), L.T. MOTOR BOARD (P

37、age 20) BU HOLDER ASSY (Page 17) MAIN BOARD, JACK BOARD (Page 16) L. SW (A) BOARD, L. SW (B) BOARD (Page 19) D. SW BOARD (Page 12) POP-UP ASSY (Page 13) POWER BOARD (Page 16) BASE (DOOR.GEAR) ASSY (Page 13) CDM ASSY (Page 20) D. SENS (IN) BOARD (Page 15) D. SENS (OUT) BOARD (Page 14) T. SENS BOARD (

38、Page 14) The parts surrounded by square are included in the solid line square in the area shown by the dotted line square . Note : Disassemble the unit in the order as shown below. 8 CDP-CX355 3-1. Case 1 two screws (CASE 3 TP2) 3 two screws (CASE 3 TP2) 4 two screws (CASE 3 TP2) 5 case 2 three scre

39、ws (CASE 3 TP2) 3-2. Bracket (F. W. ) 3 2 wire (flat type) (21 core) (CN501) 1 connector (CN504) 6 bracket (F.W.) 5 two screws (+BVTP 3 x 8) 4 screw (+BVTP 3 x 8) LED board 9 CDP-CX355 3-3. Front Panel Assy 7 two screws (+BVTP 3 x 8) 6 three screws (+BVTP 3 x 8) 5 cover (chassis) 4 screw (+BVTP 3 x

40、8) 3 connector (CN792) 8 remove the claw 9 remove the claw 2 1 q; front panel assy 3-4. DISP Board, JOG Board, KEYBOARD Board 7 remove two soldrings. 3 four screws (+BVTP 2.6 x 8) 5 two screws (+BVTP 2.6 x 8) 6 qd DISP board 9 KEYBOARD board 8 bracket (keyboard) 4 bracket main qh JOG board qj front

41、panel assy q; eight screws (+BVTP 2.6 x 8) qf five screws (B+VTP 2.6 x 8) qg seven screws (+BVTP 2.6 x 8) 2 knob (AMS) qs knob (timer) 1 knob (disc) qa wire (flat type) (21 core) (CN701) 10 CDP-CX355 3-5. LED Board, Guide (Door. T) 9 guide (door.T) 3 screw (+BVTP 3 x 8) 45 7 1 screw (+BVTP 3 x 16) 2

42、 6 LED board 8 window (internal illumination) Note during re-assembling When re-assembling, align the positions as shown. 3-6. Table (300) Assy, Cover (P.T.) 3 two screws (+BVTP 3x8) 4 cover (front) 6 door (CD) assy 8 guide (door.B) 5 7 three screws (+BVTP 3x8) q; cover (P.T.) 9 two screws (+BVTP 3

43、x 8) 1 table (300) assy 2 two 10 washers 11 CDP-CX355 3-7. D. MOTOR Board, Door Motor Assy (M83) 1 remove two soldrings. 2 D. motor board 5 door motor assy (M83) 4 belt 3 two screws (+B 2.6 x 3) 12 CDP-CX355 3-8. D. SW Board 5 two screws (+BTP 2.6 x 6) 8 D. SW board 7 holder (L-SW) 6 two claws 2 gea

44、r (door.cam) gear (door.cam) 4 gear (door.drive) 1 Move the slider (pop-up) and the lever (cam.pu) fully in the direction of the arrow A. 3 When the gear (door.cam) happens to go too deep, return it to the original position in the direction of the arrow C. The levers of the two rotary switches on th

45、e D. SW board are shown in the illustration below. slider (pop-up)lever (cam.pu) A B C 1 washer 3 washer Precaution during the gear (door.cam) installation D. SW board two rotary switches 2 Install the gear (door.cam) in the direction shown in the illustration and rotate it fully in the direction of

46、 the arrow B. 13 CDP-CX355 3-9. Base (Door. Gear) Assy 3-10. Pop-up Assy 1 step screw 3 pop-up assy 2 screw (+PTPWH 3 x 6) 3 two screws (+BVTP 3 x 8) 2 three screws (+BVTP 3 x 8) 4 base (door.gear) assy 1 connector (CN508) When re-assembling, align the positions as shown. Note during re-assembling 1

47、4 CDP-CX355 3-11. D. SENS (OUT) Board 1 connector (CN83) 2 screw (+BVTP 3 x 6) 3 4 D. SENS (OUT) board 3-12. T. SENS Board 1 connector (CN83) 3 connector (CN81) 4 connector (CN82) 2 four screws (+PTPWH 3 x 6) 5 T. SENS board 15 CDP-CX355 3-13. D. SENS (IN) Board 5 D. SENS (IN) board 3 holder (table

48、sensor) 1 two screws (+PTPWH 3 x 6) 2 two claws 4 screw (+PTPWH 3 x 6) 3-14. Back Panel Section 1 connector (CN505) 4 connector (CN508) 2 connector (CN902) 3 connector (CN507) 9 connector (CN991) 8 connector (CN901) 7 connector (CN903) 6 connector (CN503) 5 connector (CN509) qa four screws (+BVTP 3

49、x 8) q; three screws (+BVTP 3 x 8) qs back panel section 16 CDP-CX355 3-15. MAIN Board, JACK Board 1 connector (CN510) 2 connector (CN511) 8 back panel 6 MAIN board 9 JACK board 4 two screws (+BVTP 3 x 8) 5 7 three screws (+BVTP 3 x 8) 3 two screws (+BVTP 3 x 8) 3-16. POWER Board 1 screw (+BVTP 3 x 8) 4 POWER board 2 two screws (+BVTP 3 x