krell_kav-300i_sm 电路图.pdf
《krell_kav-300i_sm 电路图.pdf》由会员分享,可在线阅读,更多相关《krell_kav-300i_sm 电路图.pdf(31页珍藏版)》请在收音机爱好者资料库上搜索。
1、THE i-I=Arll=l:i IN AUI:III:I ENI:-INEI:I:ilNI KAV-300i Integrated Amplifier Service Manual v99.0 Juhe, 1999 RadioFans.CN 收音机爱 好者资料库 14.Burn-in Procedure Allow unit to sit, turnedon, for 1 day. b)Switch off the unit and let sit for five or ten minutes. Tun unit on. After 2 minutes continue with test
2、 proceddre starting at Step 8c). At Step 8e) readjust the bias for 12mV. Note: The bias should not be readjusted again. Check all the voltages stated in Step 8a). Table of Content Specifications Unit Test Procedure Test Equipment Required Special Instructions Reference Documents Amplifier Test Proce
3、dure (Functional) Amplifier Specification Test Preamplifier Test Procedure (Functional) Preamplifier Specification Test Memory and Mute Control Test Burn-in Procedure 2 3-8 3 3 3 4 5 5 6 7 8 8 Schematic Diagrams and Bill of Materials are separately attached RadioFans.CN 收音机爱 好者资料库 KAV-300i Integrate
4、d Amplifier Specifications Frequency Response 1 Hz-100KHz +0dB,-3dB Signal to Noise Ratio -95dB. A weighted Distortion 1KHz 0.06% THD 20KHz 0.3% THD Gain 36.1 dB Input Impedance 21 Ok Ohms Output Power each channel driven 8 Ohms150W 4 Ohms300W Power Consumption Idle 50W Inputs 1 balanced, 3 single-e
5、nded Outputs 1 pair speaker outputs via five way binding posts 1 single-ended Tape Monitor 1 single-ended Dimensions 19w x 3.7h x 15.5d inches 47.5w x 9.25h x 38.75d centimeters Weight Unit Shipping 25 Ibs., 11.4 kg 33 Ibs., 14.9 kg 12. Carefully reposition the input configuration back to the Jli/$3
6、 position. Power down to STAND-BY, then press POWER. After a slight delay observe that you are out of the processor mode. (See step 1 lg) a)Proceed to perform the volume tracking, input balance, mute and remote tests. Volume Tracking Input Balance Mute Remote Test that each channels ,volume matches.
7、 Balanceis tested in l dB increments. Left Balance button adjusts the right channel and vica-versa. Test that each channels balance works. Press MUTE key to prove functionality. Press Remote keys to prove functionality. Note: The input balance function can only be obtained through the remote control
8、. When performing the input balance test, observe that the volume control will extinguish, the balance LED will illuminate, the center position LED will illuminate and the left and right LEDs will illuminate as you toggle the balance controls. The volume LEDs double as the balance LED indicators. If
9、 no balance operation is being performed after a short time, the balance LED indicators will extinguish and the volume LED indicators will resume. Note: The mute function may be activated through an input select button on the second depression of the switch, then deactivated by the third depression
10、of the switch, or from the remote control. 13.HC705 Memory and Mute Control Test a) b) With a signal passing through the S3 input with the output set for 2V, and the balance control set for 3dB down, switch to STAND-BY, then power back up. Observe that after a slight delay of approximately 3-4 secon
11、ds, a signal will pass and the same settings that were previously set are retained. Press the POWER button to place the unit back to a STAND-BY condition. Disconnect all connections, turn the Variac off and set the dial to the 0 position and then remove the AC cord from the unit. 27 RadioFans.CN 收音机
12、爱 好者资料库 c)Select the $1 input, then press and hold the up arrow button until full volume. Observe a signal passin_g through both channels. Adjust the ATS-1 outputs for 2 Vrms. Check for corresponding LED illumination. 11.Preamplifier Specification Test a) Adjust the preamp outputs for 2 Vrms 1KHz. b
13、) Proceed to measure for the below requirements for both channels: 1KHz THD 0.005%GAIN = 8.7dB +/- 0.2dB 20KHz THD 0.01%NOISE -93dB DCO = 0.000V +/- 0.1V c)Proceed to check $2 leaving its output voltage set per step 8a). c)Make the proper connections between the KAV-300i and the test equipment to pa
14、ss a balanced signal through the left channel amplifier. No Load. d)Turn the Variac and observe the STAND-BY LED illuminate. Press the POWER button and observe the STAND-BY LED extinguish and the POWER LED illuminate. e) Adjust the bias for 12mY, and the dco for 0.000V +/- 20mY for both channels. Se
15、lect the B1 input, then press the up arrow until full volume and observe a smooth signal passing. Check for corresponding LRD illumination. g) Move the proper connections to monitor a smooth sinewave passing out the right channel amplifier. 9.Amplifier Specification Test a) Apply an 8 Ohm load 1KHz
16、and adjust the output for 150 Watts. b) Proceed to measure for the requirements (below) for both channels. c) d) e) THD 20Hz 0.1% THD 1KHz 0.1% THD 20KHz 0.3% THD 50mV OUTPUT 0.25% GAIN = 35.8 dB +/- 0.2dB NOISE -89dB DCO = 0.000V +/- 20mV BIAS = 12mV Check for Stability with and without an 8 Ohm lo
17、ad for both channels using a 0.015uf cap and the 0.1 uf cap. Observe that there is no oscillation. Momentarily connect the 2 Ohm load to unit. The unit should not blow a fuse, or turn off. Proceed to check that the unit clips 185 Watts or better, not below, into an 8 Ohm load for both channels 0.5 T
18、HD. f) Readjust the output for 150 Watts. Note: Turn the ATS-1 or equivalent off. g)Disconnect the amplifier from the outPut/Ioadbank and the balanced input from the unit. 10.Preamplifier Test Procedure (Functional) a) Set the ATS-1 as follows: Select the level function to read in Volts. Select the
19、generators output impedance for 50 Ohm unbalanced configuration. Adjust the generators output for approximately 0.732 Vrms 1 KHz. b)Make the proper single-ended connections to the input and the preamp outputs for both channels. 4 5 THIP- I.RAraiR IN AUralO IN(DHNiERINI: .KAV-300i Integrated Amplifie
20、r Service Manual Schematics and Bill of Materials 2 D! I.1: Component Side Artwork P7 057D58D55054 PIO 052D51 DSO D49 048 047 048 045 044 03 042 D41 I t I I I I I I i 1 I I KAV-;OOi. Faceplote Board 100-087-0; Rev. D Feb. 10, 1997 Copyrijht (.cI 1996 KRELL Induatrlee Pll D53 P5 Pe P4 5 I ower Level
21、Down Level Up Tape Monitor $3 .$2 $1 B1 01oo MP$8599 Power Toggle .,-5 11-7 ,11-10 4.7k 1N914 I 01 1N91# O4. 1N914 ,4,7 t, (:,5 0,1 uF 0.1 uF :2 ,4.7k R3 1Ok ,i IR LED REVISION RECORD COMMENTS lodified output Oarlington Added 0ATI; 12/94 TffLEt Milford! CT 064|0 RemoLe Con(rol TronsmiLLer or RLL Pre
22、amplifiers SIZORAWING NOt C D C A REY: CT, 08-JAN-93ss,l o, 1 D C B 65 White (Neutral) ,l. , RI Voltage IO0 120 2OO 22O 24O 3 Orange Greel Black Yellow Red (12o) (o) (12o) (loo) (o) Jumpers JlO-JS, JlO-JS, J11-J#, J11-J, J12-J3, J11-J, J12-JS, JS-J7 JS-J6 JS-J6 REVISION RECORD COMMENTS Added WAGOs a
23、nd lucJs rlTLE E L=L ,lu,!ries Ulfur, I CT OI4.D, KAV-300i Power Board DRAWN DSG ONAWINI; NO: 100-087-09 I SleET: 1 OF D O B lndul OV .O0-AV)I ap!s luouodLuo3 D C B A 65 Black (Hot) White (Neutral) 3 .? R1 Orange(120) - Green(100) Block(0) White(120) . Ye,o. (lOO) Red(0) Voltage 100 120 2OO 22O 240
24、Jumpers JlO-J5, JlO-JS, J11-J4, J11-J4, J12-J3, J11-J4, J12-J3, JS-J7 J5-J6 JS-J6 J8-J7 J9-J6 LTR A REVISION RECORD COMMENTS Added WAGOe ond luDe DATE: e/7 ELL Industries Milford. CT DD4DO KAV-300i Power Board DSG C100-087-09 D C B A oa 1 O- 6- 9 5srr; 1 or 1 D 02O 5 O7 !MPSW9Z Rvtolon wcord (ELL In
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- krell_kav-300i_sm 电路图 krell_kav 300 i_sm
收音机爱好者资料库所有资源均是用户自行上传分享,仅供网友学习交流,未经上传用户书面授权,请勿作他用。



Marshall-9100-62-02-Schematic电路原理图.pdf


