Drake_048_Technical_information_exchange.pdf

《Drake_048_Technical_information_exchange.pdf》由会员分享，可在线阅读，更多相关《Drake_048_Technical_information_exchange.pdf（4页珍藏版）》请在收音机爱好者资料库上搜索。

1、 Technical Information Exchange No: 048 By: Mark Gilger, WB0IQK AC4 / AC3 POWER SUPPLY TROUBLE SHOOTING By: Mark Gilger, WB0IQK In the following procedures you will be close to dangerous high voltages. Be careful. The first of the procedures has you verify the voltages at the connector. The second r

2、equires you to remove the bottom cover for further testing. The second parts is only required if indicated by the results of the first. The AC4/AC3 can be divided up into AC and DC sections as pictured below. The supply also has 4 separate sections that supply different voltages. The High Voltage (H

3、V) section supplies approximately +650 volts used by the tube final amplifier section. The Low Voltage (LV) supplies approximately +250 volts to most other sections of the radio. The Bias supply, supplies the needed negative (-) bias voltage to the amplifier sections. Last is the filament supply. Th

4、is supplies the needed AC voltage to all of the tubes in the radio. The supply also routes the transmitter ALC and amplifier relay keying voltage to plugs on the rear of the AC4/AC3 for use by a remote amplifiers. Unplug the supply from the outlet. In order to get the AC4/AC3 powered up, we need to

5、simulate the power on/off switch inside of the radio. This requires us to short pins #1 & 2 together with a jumper. Use the figure below to following the circuit. Pin #1 goes to the black primary winding of the transformer. Pin two goes to the Fuse. By shorting pins #1 & 2 you complete the circuit a

6、nd enable AC voltage to be routed to the primary of the transformer. Plug the positive (+) lead of your DC volt meter into pin #10 on the connector. This is the High Voltage +650 Volts DC. Make sure you set the meter up to read 650 Volts DC. Hook the negative (-) test of your DC volt meter to the su

7、pply chassis. AS VIEWED FROM AC4 PLUG AS VIEWED FROM T4X PLUG Technical Information Exchange 2 of 4 When performing the following step, make sure that if you do not see a voltage within several seconds, you unplug the supply immediately. In each of the following steps, you can choose to unplug the s

8、upply after each step. This will prevent damage to components while you are checking other sections. If you have 3 volt meters that can be hooked up at the same time, you can make sure all 3 voltages are present to make sure damage does not occur. Plug the supply into the AC outlet. Verify there is

9、DC voltage present. It should be in the mid +690 to +740 volt DC range with no load (I.E. power supply is not plugged into the radio). If it looks ok, turn your meter to AC and verify you have very minimal AC voltage present. This AC reading should be less than 2 volts. Move your positive lead to pi

10、n #11 and verify you have +250 volts, with less than 1 volt AC. With no load, the voltage should be close to +280 to +310 volts DC. Reverse your positive and negative leads by moving your (+) lead to the chassis ground. Move your negative (-) lead to pin #9 and verify you have negative -20 to -60 vo

11、lts present with less than a half volt AC present This is your bias voltage and can be adjusted by turning potentiometer R6 located on the front of the AC4. Without a load, this voltage can be -40 to -90 volts, or so. Turn your meter to AC and put either lead in pin #6 and pin #4. You should read ar

12、ound 12-14 volts AC. This is the filament supply voltage. The reason for checking the AC component of the DC supplies is to verify the filter capacitors are doing their job. If the filter cap is open, a high AC ripple will be noted and will cause a hum to be noted on the transmit signal. Especially

13、so in the 250 volt supply. If a problem is noted in any of the above steps. Unplug the unit from the AC outlet. Remove the 10 screws securing the bottom cover. Use the following pictures to help locate components. Note any burnt components and replace. If one of your supplies had a low voltage, the

14、problem could be a bad diode. Its easier to just replace them all than trying to isolate which one is bad. Radio shack sells a good replacement, its their catalog number 276-1114. Its a 2.5 amp 1000 volt rectifier diode. A 1N4007 in addition to many more work just fine. Technical Information Exchang

15、e 3 of 4 Resistor R3 is often the culprit in the 250 volt section. It is susceptible to over heating, which causes it to open up resulting in no, or very little voltage output. The most troublesome problem is the filter capacitors failing. They dry out or start leaking and can cause damage when they

16、 fail. Inspect around the base of each of the 5 filter capacitors for leakage. If any is noted, replace. Unplug the AC4 and let it sit for several minutes before proceeding. Put your meter in the resistance mode. Put the negative lead on the chassis ground and the positive lead on each post of each

17、capacitor. The meter should show a high resistance. The meter movement should start showing the resistance moving down scale (getting smaller) as the capacitor uses the internal meters battery to charge it up. This indicates the filter capacitor is not shorted, or opened, and might be ok. If when ch

18、ecking, the meter does not indicate the discharging of the capacitor in the above step, replace it. If the meter shows a very low resistance, the capacitor is shorted and needs to be replaced. If the meter shows a high resistance, and does not discharge, it indicates the capacitor is open. Any of th

19、ese indicate the capacitor needs to be replaced. Replacement capacitors for theAC4/AC3 are available from N)JMY through his web site4 Hayseed Hamfest Co. A complete AC4/AC3 retrofit kit is also available from TheHeathkitShop, . This is the preferred method as it replaces 99% of all components in the

20、 AC4/AC3. If you prefer to refurbish the existing filter, you can refer to the procedures written up by W6SPC http:/www.ea1ddo.es/r4b.html . It covers replacing defective R4 filter caps, but it can be easily applied to the AC4/AC3 unit. The general idea is shown here. Another procedure to rebuilding

21、 capacitor cans is written up by W8UT and is located on his web site at http:/www.boatanchors.org/filtercap.htm Several things to note: 1. The AC4 and AC3 are almost identical and can be interchanged for use on any Drake radio requiring one or the other. 2. The most notable difference is the AC3 is open frame, where the AC4 has an RFI protective cover. Technical Information Exchange 4 of 4