Icom_AT-180_user.pdf

《Icom_AT-180_user.pdf》由会员分享，可在线阅读，更多相关《Icom_AT-180_user.pdf（9页珍藏版）》请在收音机爱好者资料库上搜索。

1、 2006 Icom America Inc. Icom America, Inc. 2380 116th Ave NE Bellevue, WA 98004 425.454.7619 AT-180 Automatic Antenna Tuner Operating Instructions and Service Information Compiled from the IC-706 Operating Instructions and Service Manual 27 4RECEIVE AND TRANSMIT The AT-180 automatic antenna tuner ma

2、tches the IC- 706MKIIG to the connected antenna automatically. Once the tuner matches an antenna, the variable capacitor angles are memorized as a preset point for each frequency range (100 kHz steps). Therefore, when you change the frequency range, the variable capacitors are automatically preset t

3、o the memorized point. N No ot te e: : The AT-180 cannot be used for the 144/430 MHz band. When operating on the 144/430 MHz band, push- ing the tuner switch selects the call channel (p. 39). The AT-180 can match both HF and 50 MHz bands. However, operation is different for the HF and 50 MHz bands.

4、T TU UN NE ER R O OP PE ER RA AT TI IO ON N F Fo or r t th he e H HF F b ba an nd d: : Push TUNER to turn the tuner ON. The antenna is tuned automatically during transmission when the antenna SWR is higher than 1.5:1. When the tuner is OFF, the TUNER light goes out. F Fo or r t th he e 5 50 0 MMH Hz

5、 z b ba an nd d: : Push and hold TUNER to tune the antenna. If the TUNER light fl ashes slowly while transmitting, push and hold TUNER again to re-tune the antenna. MMA AN NU UA AL L T TU UN NI IN NG G During SSB operation on HF bands at low voice lev- els, the AT-180 may not be tuned correctly. In

6、such cases, manual tuning is helpful. Push and hold TUNER for 1 sec. to start manual tun- ing. CW mode is selected, a side tone is emitted, and the TUNER light fl ashes; then, the previous mode is select- ed. If the tuner cannot reduce the SWR to less than 1.5:1 after 20 sec. of tuning, the TUNER li

7、ght goes out. In this case, check the following: the antenna connection and feedline the antenna SWR (p. 26; meter function) T Th hr ro ou ug gh h i in nh hi ib bi it t (HF bands only) The AT-180 has a through inhibit condition. When selecting this condition, the tuner can be used at poor SWRs. In t

8、his case, automatic tuning in the HF bands activates only when exceeding SWR 3:1. Therefore, manual tuning is necessary each time you change the frequency. Although termed “through inhibit,” the tuner will be “through” if the SWR is high- er than 3:1 after tuning. T Tu un ne er r s se en ns si it ti

9、 iv ve e c co on nd di it ti io on n (HF bands only) If you require critical tuning at any time during trans- mission, select the tuner sensitive condition. See p. 55 for selection. A Au ut to omma at ti ic c t tu un ne er r s st ta ar rt t (HF bands only) If you want to turn OFF the tuner under con

10、ditions of VSWR 1.5:1 or less, use “automatic tuner on” and turn the tuner OFF. See p. 54 for turning the function ON and OFF. DO Op pt ti io on na al l A AT T- -1 18 80 0 A AU UT TOOMMA AT TI IC C A AN NT TE EN NN NA A T TU UN NE ER Ro op pe er ra at ti io on n TUNER/CALL Lights to indicate the AT-

11、180 is turned ON. TUNER/CALL Flashes to indicate re-tuning is necessary. C CA AU UT TI IO ON N: :N NE EV VE ER R transmit with the tuner ON when no antenna is connected. This will damage both the transceiver and the antenna tuner. TUNER/CALL Push and hold for 1 sec. to start manual tuning. CONVENIEN

12、T IC-706MKIIG.qxd 02.3.27 13:53 Page 27 62 I A AT T- -1 18 80 0 i in nt te er rn na al l s sw wi it tc ch h d de es sc cr ri ip pt ti io on n The optional AT-180 has 3 operating conditions for HF band operation. Select a suitable condition according to your antenna system. Remove the top cover of th

13、e AT-180. Set the tuner switches to the desired positions according to the table below. S Sp pe ec ci if fi ic ca at ti io on ns s f fo or r t th he e A AT T- -1 18 80 0 Frequency coverage : 1.954 MHz Input impedance: 50 Maximum input: 120 W power Minimum tuning: 8 W power Matching impedance : 16.71

14、50 (HF band) range20125 (50 MHz band) Tuning accuracy: Less than SWR 1.5:1 Insertion loss: Less than 1.0 dB (after tuning) Power supply: 13.8 V DC/1 A (supplied from requirementsthe transceivers ACC socket) Dimensions (mm/in): 167(W)58.6(H)225(D) 6916(W)2517(H)878(D) Weight: 2.4 kg; 5 lb 4 oz Suppli

15、ed accessories: coaxial cable (1 m), ACC cable (DIN 13 pins) A AT T- -1 18 80 0 i in ns si id de e t to op p c co ov ve er r C Co on nn ne ec ct to or r i in nf fo or rmma at ti io on n f fo or r A AC CC C( (2 2) ) s so oc ck ke et t S2S1 D CB A ACC 2 1 2 3 4 76 5 P PI IN N N NO O. ./ / N NA AMME E

16、D DE ES SC CR RI IP PT TI IO ON N 8 V Regulated 8 V output. (10 mA max.) GNDConnects to ground. SEND Input/output pin. Goes to ground when transmitting (20 mA max). When grounded, transmits. BAND Band voltage output. (Varies with amateur band; 0 to 8.0 V). ALCALC output voltage (4 to 0 V). NCNo conn

17、ection. 13.8V13.8 V output when power is ON (1 A max). S SWW P Po os si it ti io on nO Op pe er ra at ti io on n S1 A (default) The tuner operating condition is set by S2 described below. B THROUGH INHIBIT The tuner tunes the antenna even when the antenna has poor SWR (up to VSWR 3:1 after tuning).

18、In this case, manual tun- ing is necessary each time you change the frequency although the tuner automatical- ly starts tuning when the VSWR is higher than 3:1. This setting is called “through inhibit,” however, the tuner is set to “through” if the VSWR is higher than 3:1 after tuning. S2 C TUNER SE

19、NSITIVE CONDITION The tuner tunes each time you transmit (except SSB mode). Therefore, the lowest SWR is obtained at any given time. For SSB mode, the same condition as the “D” position. D (default) NORMAL CONDITION The tuner tunes when the SWR is higher than 1.5:1. Therefore, the tuner activates only when tuning is necessary. 10OPTIONAL INSTALLATIONS/SETTINGS IC-706MKIIG.qxd 02.3.27 13:53 Page 62