IC-R10_user.pdf

《IC-R10_user.pdf》由会员分享，可在线阅读，更多相关《IC-R10_user.pdf（84页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL iR10 COMMUNICATIONS RECEIVER This device complies with Part 15 of the FCC rules. Operation is sub- ject to the following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cau

2、se undesired operation. Downloaded by? Amateur Radio Directory? ? www.hamdirectory.info RWARNING! NEVERconnect the receiver to an AC outlet. This may pose a fire hazard or result in an electric shock. RWARNING! NEVER operate the receiver with a headset or other audio accessories at high volume level

3、s. Hearing experts advise against continuous high volume op- eration. If you experience a ringing in your ears, reduce the volume level or discontinue use. NEVERconnect the receiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruin the receiver. NEVERcut the DC

4、 power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the receiver might be damaged. NEVERexpose the receiver to rain, snow or any liquids. DO NOTconnect the receiver to a power source using re- verse polarity. This connection will not only blow fuses bu

5、t also may damage the receiver. i Versions of the IC-R10 which display the “CE” symbol on the serial number seal, comply with the ETSI specifi ca- tion prETS300 684 (EMC product standard for Commercially Available Amateur Radio Equipment). CAUTIONSIMPORTANT READ ALL INSTRUCTIONSCAREFULLYbe- fore att

6、empting to operate the receiver. SAVE THIS INSTRUCTION MANUALThis instruction manual contains important safety and operating in- structions for the IC-R10. EXPLICIT DEFINITIONS The following explicit defi nitions apply to this manual. WORDDEFINITION RWARNING Personal injury, fi re hazard or electric

7、 shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fi re or electric shock. ii UNPACKING Accessories included with the receiver: Qty. 1q Antenna.1 1w Handstrap.1 1e Belt clip (with 2 screws).1 41r Wall charger*.1 1t Ni-Cd batter

8、ies .4 *Not supplied with some versions. DO NOTuse or place the receiver in areas with tempera- tures below 10C (+14F) or above +50C (+122F) or, in areas subject to direct sunlight, such as the dashboard. AVOIDplacing the receiver in excessively dusty environ- ments. AVOIDthe use of chemical agents

9、such as benzine or al- cohol when cleaning, as they damage the receiver surfaces. Even when the receiver power is OFF, a slight current still fl ows in the circuits. Remove cell batteries from the receiver when not using it for a long time. Otherwise, the installed bat- teries will become exhausted.

10、 For U.S.A. only Caution:Changes or modifi cations to this receiver, not ex- pressly approved by Icom Inc., could void your authority to operate this receiver under FCC regulations. qwe r t TABLE OF CONTENTS iii IMPORTANT.i EXPLICIT DEFINITIONS .i CAUTIONS .i UNPACKING.ii TABLE OF CONTENTS .iii OPER

11、ATING THEORY .iv OPERATING NOTES.iv 1PANEL DESCRIPTION.16 IFront and side panels .1 ITop panel .2 IFunction display.3 IKeypad .5 2Ni-Cd BATTERIES AND ACCESSORIES.79 ICharging Ni-Cd batteries .7 ICharging precautions .7 IAbout Ni-Cd batteries .7 IBattery installation .8 ICharging connections .8 IAcce

12、ssory attachment .9 3BASIC OPERATION .1022 IGeneral .10 ISelecting VFO mode .10 ISelecting a receive mode .12 ISelecting a tuning step .13 ITuning a frequency (via the keypad) .14 ITuning a frequency (via the DIAL) .15 IDial select steps .16 IBand scope function .17 IListening example 1.19 IListenin

13、g example 2.21 4MEMORY MODE .2334 IGeneral .23 ISelecting memory mode .23 ISetting a bank and memory channel .24 IProgramming a memory channel1 .25 IProgramming a memory channel2 .26 IProgramming a memory channel3 .27 IProgramming example 1 .29 IProgramming example 2 .30 IProgramming example 3 .31 I

14、Memory copy .33 ICopying example 1 .34 ICopying example 2 .34 5SCANNING OPERATION .3546 IGeneral .35 IBefore scanning.37 IFull scan .39 IMemory scan .39 IProgram scan .40 IAuto memory write scan .41 IBANK scan .43 IMode select scan.44 ISkip function .45 ISIGNAVI function.46 6PRIORITY WATCH .4749 IGe

15、neral .47 7EASY MODE.50 IGeneral .50 IEASY mode operation .50 8EDIT FUNCTION .5158 TABLE OF CONTENTS iv OPERATING THEORY Electromagnetic radiation which has frequencies of 20,000 Hz (20 kHz*) and above is called radio frequency (RF) energy because it is useful in radio transmissions. The IC-R10 re-

16、ceives RF energy from 0.5 MHz to 1300 MHz* and converts it into audio frequency (AF) energy which in turn actuates a loudspeaker to create sound waves. AF energy is in the range of 20 to 20,000 Hz. *kHz is an abbreviation of kilohertz or 1000 hertz, MHz is abbreviation of megahertz or 1,000,000 hert

17、z, where hertz is a unit of frequency. IGeneral .51 IMemory channel edit .51 IProgram scan channel edit .55 IEASY mode channel edit.55 IProgram scan or EASY mode channel edit .57 9SET MODE .5962 IGeneral .62 10 OTHER FUNCTIONS.6371 ILow battery indicator .63 IAFC function .63 IMonitor function .64 I

18、Lock function .64 IATT function .65 INB/ANL function .65 ISleep timer .66 IUser TS setting .66 IMemory search function .67 IAuto mode and TS function .69 IResetting the CPU .70 IData cloning .71 11 ALPHANUMERIC KEY ASSIGNMENT.72 12 CONTROL COMMANDS .7374 IGeneral .73 IData format .73 ICommand table

19、.73 13 TROUBLESHOOTING.7576 14 SPECIFICATIONS .77 15 OPTIONS .78 OPERATING NOTES The IC-R10 may receives its own oscillated frequency, result- ing in no reception or only noise reception, on some frequen- cies. The IC-R10 may receive interference from extremely strong signals on different frequencie

20、s or when using an external high-gain antenna. 1 1 PANEL DESCRIPTION IFront and side panels FUNCTION SWITCH (pgs. 5, 6) While pushing FUNC, the sec- ondary functions of switches and controls can be accessed. FUNCTION DISPLAY (p. 3) Indicates the operating condition. KEYPAD (pgs. 5, 6) Numeral and ot

21、her function keys for tuning and activating func- tions. SPEAKER Emits the receive audio. CI-V JACK (p. 73) Connect the optional OPC-478 CLONING CABLE for remote control or data cloning. EXTERNAL DC POWER JACK (p. 8) Connect the supplied wall charg- er for charging the installed Ni-Cd battery cells.

22、 Be careful of overcharging! Operation with an external DC power source simultaneously charges the installed batteries. When CHARGE switch is ON, see p. 8. 1PANEL DESCRIPTION 2 ITop panel ANTENNA CONNECTOR (p. 9) Connects the supplied flexible antenna. Be careful when con- necting an external antenn

23、a (See Operating Notes, p. iv). VOLUME CONTROL VOL (p. 10) Adjusts the audio output level. SQUELCH CONTROL SQL (p. 11) Varies the squelch threshold point for audio mute. Pushing MONI opens the squelch momentarily. Varies the RF gain in LSB, USB and CW modes. EXTERNAL SPEAKER JACK SP Connect an 8 ohm

24、 optional speaker or an earphone, if de- sired. The internal speaker will not function when either option is connected. Connect the optional OPC- 478/479 CLONING CABLE for cloning from a PC or another IC- R10 (p. 71). TUNING CONTROL DIAL Used to set an operating fre- quency (p. 15), memory channel (

25、p. 24), etc. 1PANEL DESCRIPTION 3 ATTVSCEASYVFOMEMO AFCCWUSBLSBAMWFM 1234568790 A IFunction display 1 4 PANEL DESCRIPTION qSLEEP TIMER INDICATOR Appears while the sleep timer is activated (p. 66). wFUNCTION INDICATOR Appears while the function (FUNC) switch is pushed. eMEMORY MODE INDICATOR Appears

26、while in memory mode (p. 23). rVFO MODE INDICATOR Appears while in VFO mode (p. 11). tRECEIVE MODE INDICATOR Indicates the selected receive mode (p. 12). yEASY MODE INDICATOR Appears while in easy mode (p. 50). uVSC INDICATOR Appears while the VSC function is turned ON (p. 38). iATTENUATOR INDICATOR

27、 Appears while the attenuator is turned ON (p. 65). oAFC INDICATOR Appears while the AFC function is turned ON (p. 63). !0LOCK INDICATOR Appears while the lock function is activated (p. 64). !1MULTI-FUNCTION DOT MATRIX Indicates the following items: Opening message (p. 10) Receive frequency (p. 11) Tuning steps (p. 13) Band scope (p. 17) Memory bank and channel number (p. 23) Memory name (p.