ID-RP2000V_user.pdf

《ID-RP2000V_user.pdf》由会员分享，可在线阅读，更多相关《ID-RP2000V_user.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、VHF DIGITAL VOICE REPEATER id-rp2000v Instruction Manual This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference tha

2、t may cause undesired operation. IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the re- peater. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating in- structions for the ID-RP2000V. Refer to the ID-RP2 instruction manual, supplied with th

3、e ID-RP2C, about the Digital Smart Technolo- gies for Amateur Radio (D-STAR) system repeater instruction, installation and precautions, etc. for de- tails. Because this instruction manual describes ID- RP2000Vs particular installation and precautions only. EXPLICIT DEFINITIONS WORD DEFINITION R WARN

4、ING Personal injury, fi re hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk or personal injury, fi re or elec- tric shock. PRECAUTIONS R WARNING RF EXPOSURE! This device emits Radio Frequency (RF) energy. Extreme caution should

5、be observed when operating this device. If you have any questions regarding RF exposure and safety standards, please refer to the Federal Communica- tions Commission Office of Engineering and Tech- nologys report on Evaluating Compliance with FCC Guidelines for Human Radio Frequency Electromag- neti

6、c Fields (OET Bulletin 65). R WARNING HIGH VOLTAGE! NEVER attach an antenna or internal antenna connector during trans- mission. This may result in an electrical shock or burn. R WARNING HIGH VOLTAGE! NEVER install the antenna at any place that person touch the an- tenna easily during transmission.

7、This may result in an electrical shock or burn. R NEVER apply AC to the DC 13.8V IN connector. This could cause a fi re or ruin the repeater. R NEVER apply more than 16 V DC, such as a 24 V battery, to the DC 13.8V IN connector on the re- peater. This could cause a fi re or ruin the repeater. R NEVE

8、R let metal, wire or other objects touch any internal part or connectors on the repeater. This may result in an electric shock. R NEVER operate or touch the ID-RP2000V with wet hands. This may result in an electric shock or damage to the repeater unit. R NEVER expose the ID-RP2000V to rain, snow or

9、any liquids. These units have no water protection. AVOID using or placing the ID-RP2000V in areas with temperatures below 10C (+14F) or above +50C (+122F). Be aware that temperatures can exceed 80C (+176F), resulting in permanent damage to the re- peater if left there for extended periods. AVOID pla

10、cing the ID-RP2000V in excessively dusty environments or in direct sunlight. Place the repeater in a secure place to avoid inadver- tent use by children. DO NOT use chemical agents such as benzine or alcohol when cleaning, as they can damage the re- peaters surfaces. DO NOT modify the repeater for a

11、ny reason. Use the specifi ed fuse only. For the U.S.A. only CAUTION: Changes or modifi cations to this repeater, not expressly approved by Icom Inc., could void your authority to operate this repeater under FCC regula- tions. i Icom, Icom Inc. and the logo are registered trade- marks of Icom Incorp

12、orated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/ or other countries. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other products or brands are

13、registered trademarks or trademarks of their respective holders. ii TABLE OF CONTENTS IMPORTANT . i EXPLICIT DEFINITIONS . i PRECAUTIONS . i FOR CLASS B UNINTENTIONAL RADIATORS. ii TABLE OF CONTENTS . ii SUPPLIED ACCESSORIES . ii 1 SYSTEM OUTLINE . 1 2 PANEL DESCRIPTIONS . 2 Front panel . 2 Rear pan

14、el . 2 3 CONNECTIONS AND INSTALLATIONS . 35 Precautions . 3 D About coaxial cable . 3 About the power supply . 3 When install into system rack . 4 Rubber feet attachment . 4 Grounding . 4 System connections . 5 4 DRIVER INSTALLATIONS . 626 Microsoft Windows XP (Service Pack 2) . 6 Microsoft Windows

15、2000 . 11 Microsoft Windows 98SE/Me . 15 Microsoft Windows Vista . 18 COM port confi rmation . 22 D Microsoft Windows XP/2000 . 22 D Microsoft Windows 98SE/Me . 23 D Microsoft Windows Vista . 24 USB driver un-installation . 25 5 UTILITY INSTALLATION . 2729 Installation . 27 Un-installation . 29 6 RE

16、PEATER SETTINGS . 30 Frequency setting for ID-RP2000V . 30 7 MAINTENANCE . 31 Troubleshooting . 31 About cleaning . 31 Fuse replacement . 31 8 SPECIFICATIONS AND SYSTEM UNITS . 32 Specifi cations . 32 System units . 32 9 ABOUT CE . 33 SUPPLIED ACCESSORIES r w e q t q Power cable (OPC- 1309; approx.

17、1 m; 3.3 ft) . 1 w Control cable (OPC-1069) . 1 e Rubber feet . 4 r Spare fuses (FGB10A) . 2 t CD . 1 FOR CLASS B UNINTENTIONAL RADIATORS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed t

18、o provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm- ful interference to radio communications. However, the

19、re is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn- ing the equipment off and on, the user is encouraged to try to correct the interference by one or mor

20、e of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and re- ceiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician fo

21、r help. 1 SYSTEM OUTLINE 1 The ID-RP2000V is installed into the D-STAR re- peater system for operation. The ID-RP2000V never functions as a repeater with- out the ID-RP2C because it has no relay function. ID-RP2000V The ID-RP2000V is a 144 MHz digital voice and slow-speed data repeater (4.8 kbps), a

22、nd connects to the ID-RP2C. NOTE: No audio CODEC is performed in the ID- RP2000V, and thus the ID-RP2000V re- ceives and transmits 4.8 kbps serial data only. Different frequencies are used for each transmis- sion and reception in semi-duplex mode. The ID-RP2000V utility software, supplied with the I

23、D-RP2000V, and a PC are required for both re- ceive and transmit frequency settings. Zone Area Signal Internet Antenna ID-RP2L* POWER 10 BESE-T SERVICE 1 SERVICE 2 ASSIST 1ASSIST 2 ID-RP2C ID-RP2000V InternetInternetInternet SERVICE T SERVICE RPOWER ID-RP2V Repeater Controller *The ID-RP2L is not av

24、ailable in European countries as of May 2008. 2 2 PANEL DESCRIPTIONS Front panel q POWER SWITCH POWER The power switch for the ID-RP2000V. w POWER INDICATOR The LED indicator for the ID-RP2000V, and lights when the power is turned ON. e HIGH/LOW POWER SELECT SWITCH H/L Selects the transmit output po

25、wer High (approx. 25 W) and Low (approx. 2.5 W). r SERVICE CONNECTOR T SERVICE T (p. 30) Connects a PC via a USB cable (A-B type; purchase separately) to set the transmit frequency. t SERVICE CONNECTOR R SERVICE R (p. 30) Connects a PC via a USB cable (A-B type; purchase separately) to set the recei

26、ve frequency. qerwt Rear panel q RECEIVE ANTENNA CONNECTOR RX ANT (p. 5) Connect a 144 MHz band antenna through a du- plexer. w TRANSMIT ANTENNA CONNECTOR TX ANT (p. 5) Connect a 144 MHz band antenna through a du- plexer. e COOLING FAN r POWER CONNECTOR DC13.8V (p. 5) Connect to the ID-RP2C via the

27、supplied DC power cable (OPC-1309) to be supplied the DC power. t CONT I/O (p. 5) Connect to the ID-RP2C via the supplied control cable for received or transmitted serial data com- munication. y GROUND TERMINAL GND (p. 4) Connect to a ground to prevent electrical shocks, TVI, BCI and other problems.

28、 werqty 3 3 CONNECTIONS AND INSTALLATIONS Precautions NEVER expose the ID-RP2000V to rain, snow or any liquids. NEVER connect the repeater to a power source using reverse polarity. This will damage the repeater. And turn the repeater power OFF when connecting a power supply. AVOID using or placing t

29、he ID-RP2000V in areas with temperature below 10C (+14F) or above +50C (+122F). AVOID placing the ID-RP2000V in excessively dusty environments or in direct sunlight. AVOID placing the ID-RP2000V against walls or put- ting anything on top of the units. This will obstruct heat dissipation. D About coa

30、xial cable Type-N connector assembling Slide the nut, washer, rubber gasket and clamp over the coaxial cable, then cut the end of the cable evenly. Strip the cable and fold the braid back over the clamp. Soft solder the center conductor. Install the center conductor pin and solder it. Carefully slid

31、e the plug body into the place aligning the center conductor pin on the cable. Tighten the nut onto the plug body. q w e r 15 mm 3 mm 6 mm No space Solder hole Be sure the center conductor is the same height as the plug body. Clamp Center conductor Washer Nut Rubber gasket Use 50 of impedance for bo

32、th antenna (at Feeding power point) and coaxial cable. Type-N connector is used for the connection between the ID-RP2000V and antenna. RECOMMENDATION: Install a surge protector between the ID-RP2000V and antenna. About the power supply Make sure that the DC power supply that is used with the ID-RP20

33、00V system meets the followings: Output voltage : 13.8 V DC 15% Current capacity : At least the total current consump- tion of the connected equipment. 4 3CONNECTIONS AND INSTALLATIONS When install into system rack The ID-RP2000V is designed to install into the 19-inch rack (EIA standard) directly.

34、Use the supplied bolts with the rack when fixing the ID-RP2000V. We recommend to use the rack that has rails be- cause the weight of the ID-RP2000V is approx. 7.5 kg (16.5 lbs). Rubber feet attachment q Cross section w Attach the supplied rubber feet onto the bottom of the ID-RP2000V as shown at lef

35、t when you do not install the ID-RP2000V in the 19-inch rack. Desktop opera- tion can be performed. Grounding To prevent electrical shock, television interference (TVI), broadcast interference (BCI) and other prob- lems, ground the transceiver through the GROUND terminal on the rear panel. For the b

36、est results, connect a heavy gauge wire or strap to a long earth-sunk copper rod. Make the distance between the GND terminal and ground as short as possible. R WARNING: NEVER connect the GND ter- minal to a gas or electric pipe, since the connec- tion could cause an explosion or electric shock. 5 3C

37、ONNECTIONS AND INSTALLATIONS System connections Duplexer (purchase separately) ID-RP2000V ID-RP2C A B B A OPC-1380 (supplied w/ID-RP2C) to AH-106/107*to AH-106/107* OPC-1309 (supplied w/ID-RP2000V) Control cable (supplied w/ID-RP2000V) ID-RP2L* (Assist 1) 144 MHz band antenna (purchase separately) I

38、D-RP2L* (Assist 2) AC outlet AC power cable External DC power supply 13.8 V Black _ Red + Coaxial cables (purchase separately) *Not available in European countries as of May 2008. 4 6 DRIVER INSTALLATIONS The USB (Universal Serial Bus) cable (A-B type; purchase separately) is used for the connection

39、 between the ID- RP2000V and a PC. So, the USB driver installation is required for the PC. In addition, individual USB driver installation is re- quired for each connector, because of the communi- cation port number difference. In this instruction, describes with the installation of the ID-RP2000V S

40、ERVICE T connector for example. NOTE: The repeater unit connection may not be recog- nized with the PC according to the using USB cable length. Use the shorter USB cable as possible is recom- mended. Microsoft Windows XP (Service Pack 2) q Start up the Windows. Quit all applications if activated. w

41、Insert the CD supplied with the ID-RP2000V, into the CD drive. e Connect the PC and ID-RP2000V SERVICE T connector using with a USB cable (A-B type; pur- chase separately). r “Found New Hardware ID-RP2000V SERVICE T” appears as at left. Click Select t The “Found New Hardware Wizard” will appear as at left. Select “No, not this time” and click Next. Continue to the next page. 7 4DRIVER INSTALLATIONS Microsoft Windows XP (Service Pack 2) continued Click Select y When the dialog box as at left is displayed, select “Install the software automatically (Reco