ID-RP4000V_user.pdf

《ID-RP4000V_user.pdf》由会员分享，可在线阅读，更多相关《ID-RP4000V_user.pdf（38页珍藏版）》请在收音机爱好者资料库上搜索。

1、UHF DIGITAL VOICE REPEATER id-rp4000v Instruction Manual This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference tha

2、t may cause undesired operation. IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the re- peater. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating in- structions for the ID-RP4000V. Refer to the ID-RP2 instruction manual, supplied with th

3、e ID-RP2C, about D-star system repeater instruction, installation and precautions, etc. for details. Because of this instruction manual describes ID- RP4000Vs particular installation and precautions only. EXPLICIT DEFINITIONS WORD DEFINITION R WARNING Personal injury, fjre hazard or electric shock m

4、ay occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk or personal injury, fire or electric shock. PRECAUTIONS R WARNING RF EXPOSURE! This device emits Radio Frequency (RF) energy. Extreme caution should be observed when operating this device. If you have any

5、questions regarding RF exposure and safety standards please refer to the Federal Communica- tions Commission Office of Engineering and Tech- nologys report on Evaluating Compliance with FCC Guidelines for Human Radio Frequency Electromag- netic Fields (OET Bulletin 65). R WARNING HIGH VOLTAGE! NEVER

6、 attach an antenna or internal antenna connector during trans- mission. This may result in an electrical shock or burn. R WARNING HIGH VOLTAGE! NEVER install the antenna at any place that person touch the an- tenna easily during transmission. This may result in an electrical shock or burn. R NEVER a

7、pply AC to the DC 13.8V IN connector. This could cause a fire or ruin the repeater. R NEVER apply more than 16 V DC, such as a 24 V battery, to the DC 13.8V IN connector on the re- peater. This could cause a fire or ruin the repeater. R NEVER let metal, wire or other objects touch any internal part

8、or connectors on the repeater. This may result in an electric shock. R NEVER operate or touch the ID-RP4000V with wet hands. This may result in an electric shock or damage to the repeater unit. R NEVER expose the ID-RP4000V to rain, snow or any liquids. These units have no water protection. AVOID us

9、ing or placing the ID-RP4000V in areas with temperatures below 10C (+14F) or above +50C (+122F). Be aware that temperatures can exceed 80C (+176F), resulting in permanent damage to the re- peater if left there for extended periods. AVOID placing the ID-RP4000V in excessively dusty environments or in

10、 direct sunlig ht. Place the repeater in a secure place to avoid inadver- tent use by children. DO NOT use chemical agents such as benzine or al- cohol when cleaning, as they can damage the re- peaters surfaces. DO NOT modify the repeater for any reason. Use the specified fuse only. For the U.S.A. o

11、nly CAUTION: Changes or modifications to this repeater, not expressly approved by Icom Inc., could void your authority to operate this repeater under FCC regula- tions. i Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Ger

12、many, France, Spain, Russia and/or other countries. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holde

13、rs. ii TABLE OF CONTENTS IMPORTANT . i EXPLICIT DEFINITIONS . i PRECAUTIONS . i TABLE OF CONTENTS . ii SUPPLIED ACCESSORIES . ii 1 SYSTEM OUTLINE . 1 2 PANEL DESCRIPTIONS . 2 n Front panel . 2 n Rear panel . 2 3 CONNECTIONS AND INSTALLATIONS . 35 n Precautions . 3 D About coaxial cable . 3 n About t

14、he power supply . 3 n When install into system rack . 4 n Rubber feet attachment . 4 n Grounding . 4 n System connections . 5 4 DRIVER INSTALLATIONS . 626 n Microsoft Windows XP (Service Pack 2) . 6 n Microsoft Windows 2000 . 11 n Microsoft Windows 98SE/Me. 15 n Microsoft Windows Vista . 18 n COM po

15、rt confirmation . 22 D Microsoft Windows XP/2000 . 22 D Microsoft Windows 98SE/Me . 23 D Microsoft Windows Vista . 24 n USB driver un-installation . 25 5 UTILITY INSTALLATION . 2729 n Installation . 27 n Un-installation . 29 6 REPEATER SETTINGS . 30 n Frequency setting for ID-RP4000V . 30 7 MAINTENA

16、NCE . 31 n Troubleshooting . 31 n About cleaning . 31 n Fuse replacement . 31 8 SPECIFICATIONS AND SYSTEM UNITS . 32 n Specifications . 32 n System units . 32 9 ABOUT CE . 33 SUPPLIED ACCESSORIES r w e q t q Power cable (OPC- 1309; approx. 1 m; 3.3 ft) . 1 w Control cable (OPC-1069) . 1 e Rubber fee

17、t . 4 r Spare fuses (FGB10A) . 2 t Utility CD . 1 FOR CLASS B UNINTENTIONAL RADIATORS This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful inte

18、rference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm- ful interference to radio communications. However, there is no guarantee that interference will not occur

19、in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turn- ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate th

20、e receiving antenna. Increase the separation between the equipment and re- ceiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 1 SYSTEM OUTLINE 1 The ID-RP4000V is install

21、ed into the Digital Smart Technologies for Amateur Radio (D-STAR) repeater system for operation. The ID-RP4000V never functions as a repeater with- out ID-RP2C, due to no relay function is built-in. n ID-RP4000V ID-RP4000V is a 440 MHz digital voice and slow- speed data repeater (4.8 kbps) and conne

22、cts to the ID-RP2C. NOTE: No audio CODEC is performed in the ID- RP4000V, thus the ID-RP4000V receives and transmits 4.8 kbps serial data only. Different frequencies are used for each transmis- sion and reception in semi-duplex mode. The ID-RP4000V utility software, supplied with the ID-RP4000V, and

23、 a PC are required for both re- ceive and transmit frequency settings. Zone Area Signal Internet Antenna ID-RP2L* POWER 10 BESE-T SERVICE 1SERVICE 2 ASSIST 1ASSIST 2 ID-RP2C ID-RP4000V InternetInternet SERVICE TSERVICE RPOWER ID-RP2V Repeater Controller *ID-RP2L is not available in European countrie

24、s by the present on March 2008. 2 2 PANEL DESCRIPTIONS n Front panel q POWER SWITCH POWER The power switch for ID-RP4000V. w POWER INDICATOR The LED indicator for the ID-RP4000V and lights when the power is turned ON. e HIGH/LOW POWER SELECT SWITCH H/L Selects the transmit output power High (approx.

25、 25 W) and Low (approx. 2.5 W). r SERVICE CONNECTOR T SERVICE T (p. 30) Connects a PC via an USB cable (A-B type; pur- chase separately) to set the transmit frequency. t SERVICE CONNECTOR R SERVICE R (p. 30) Connects a PC via an USB cable (A-B type; pur- chase separately) to set the receive frequenc

26、y. q wer t n Rear panel q RECEIVE ANTENNA CONNECTOR RX ANT (p. 5) Connect a 440 MHz band antenna through a du- plexer. w TRANSMIT ANTENNA CONNECTOR TX ANT (p. 5) Connect a 440 MHz band antenna through a du- plexer. e COOLING FAN r POWER CONNECTOR DC13.8V (p. 5) Connects to ID-RP2C via the supplied D

27、C power cable (OPC-1309) to be supplied the DC power. t CONT I/O (p. 5) Connects to ID-RP2C via the supplied control cable for received or transmitted serial data com- munication. y GROUND TERMINAL GND (p. 4) Connects to a ground to prevent electrical shocks, TVI, BCI and other problems. qrtyew 3 3

28、CONNECTIONS AND INSTALLATIONS n Precautions NEVER expose the ID-RP4000V to rain, snow or any liquids. NEVER connect the repeater to a power source using reverse polarity. This will damage the repeater. And turn the repeater power OFF when connecting a power supply. AVOID using or placing the ID-RP40

29、00V in areas with temperature below 10C (+14F) or above +50C (+122F). AVOID placing the ID-RP4000V in excessively dusty environments or in direct sunlight. AVOID placing the ID-RP4000V against walls or put- ting anything on top of the units. This will obstruct heat dissipation. D About coaxial cable

30、 Slide the nut, washer, rubber gasket and clamp over the coaxial cable, then cut the end of the cable evenly. Strip the cable and fold the braid back over the clamp. Soft solder the center conductor. Install the center conductor pin and solder it. Carefully slide the plug body into place aligning th

31、e center conductor pin on the cable. Tighten the nut onto the plug body. r e 15 mm 3 mm 6 mm No space Solder hole Be sure the center conductor is the same height as the plug body. Clamp Center conductor Washer Nut Rubber gasket q w Use 50 of impedance for both antenna (at Feeding power point) and co

32、axial cable. Type-N connector is used for the connection between ID-RP4000V and antenna. RECOMMENDATION: Install a lightning protector between the ID-RP4000V and antenna. n About the power supply Be sure to the DC power supply that used with the ID- RP4000V system is meet the followings: Output volt

33、age : 13.8 V DC 15% Current capacity : At least the total current consump- tion of the connected equipments. 4 3CONNECTIONS AND INSTALLATIONS n When install into system rack The ID-RP4000V is designed to install into the 19-inch rack (EIA standard) directly. Use the supplied bolts with the rack when

34、 fixing the ID-RP4000V. We recommend to use the rack that has rails due to the weigh of the ID-RP4000V is approx. 7.5 kg (16.5 lbs). n Rubber feet attachment q Cross section w Attach the supplied rubber feet onto the bottom of the ID-RP4000V as shown at left when not installed into 19-inch rack. Des

35、ktop operation can be performed. n Grounding To prevent electrical shock, television interference (TVI), broadcast interference (BCI) and other prob- lems, ground the transceiver through the GROUND terminal on the rear panel. For best results, connect a heavy gauge wire or strap to a long earth-sunk

36、 copper rod. Make the distance between the GND terminal and ground as short as possible. R WARNING: NEVER connect the GND ter- minal to a gas or electric pipe, since the connec- tion could cause an explosion or electric shock. 5 3CONNECTIONS AND INSTALLATIONS n System connections Duplexer (purchase

37、locally) ID-RP4000V ID-RP2C A B B A OPC-1380 (supplied w/ID-RP2C) to AH-106/107*to AH-106/107* OPC-1309 (supplied w/ID-RP4000V) Control cable (supplied w/ID-RP4000V) ID-RP2L* (Assist 1) 430/440 MHz band antenna (purchase locally) ID-RP2L* (Assist 2) AC outlet AC power cable External DC power supply

38、13.8 V Black _ Red + Coaxial cables (purchase locally) *Not available in European countries by the present on March 2008. 4 6 DRIVER INSTALLATIONS The USB (Universal Serial Bus) cable (A-B type; purchase separately) is used for the connection between ID- RP4000V and a PC. So, the USB driver installa

39、tion is required for the PC. In addition, individual USB driver installation is re- quired for each connector, because the communica- tion port number difference. In this instruction, describes with the installation of the ID-RP4000V SERVICE T connector for example. NOTE: The repeater unit connectio

40、n may not be recog- nized with the PC according to the using USB cable length. Use the shorter USB cable as possible is recom- mended. n Microsoft Windows XP (Service Pack 2) q Start up the Windows. Quit all applications if activated. w Insert the CD that comes with the ID-RP4000V, into the CD drive

41、. e Connect the PC and ID-RP4000V SERVICE T connector using with an USB cable (A-B type; pur- chase separately). r “Found New Hardware ID-RP4000V SERVICE T” appears as at left. Click Select t The “Found New Hardware Wizard” will come up as at left. Select “No, not this time” then click Next. + Conti

42、nue to the next page. 7 4DRIVER INSTALLATIONS n Microsoft Windows XP (Service Pack 2) continued Click Select y When the dialog box as at left is displayed, se- lect “Install the software automatically (Recom- mended),” then click Next. u The wizard starts searching for the driver and shows the dialog as at left during search