IC-7100_advanced_user.pdf

《IC-7100_advanced_user.pdf》由会员分享，可在线阅读，更多相关《IC-7100_advanced_user.pdf（379页珍藏版）》请在收音机爱好者资料库上搜索。

1、ADVANCED INSTRUCTIONS i7100 20 CONTROL COMMAND 15 VOICE TX FUNCTION 14 VOICE MEMORY FUNCTION 13 USING AN SD CARD 12 SCAN OPERATION 11 MEMORY OPERATION 10 GPS/GPS-A OPERATION 9 D-STAR OPERATION 8 D-STAR OPERATION 7 D-STAR INTRODUCTION 6 FUNCTIONS FOR TRANSMIT 5 FUNCTIONS FOR RECEIVE 4 RECEIVE AND TRA

2、NSMIT 3 BASIC OPERATION 2 INSTALLATION AND CONNECTIONS 1 PANEL DESCRIPTION 16 ANTENNA TUNER OPERATION 17 SET MODE 18 DATA COMMUNICATION 19 MAINTENANCE 21 SPECIFICATIONS AND OPTIONS INTRODUCTION HF/VHF/UHF ALL MODE TRANSCEIVER i 3BASIC OPERATION 3-13 Previous view Setting frequency (Continued) Band e

3、dge warning beep D You can hear a beep tone when you tune into or out of an amateur bands frequency range. A regular beep sounds when you tune into a range, and an lower tone error beep sounds when you tune out of a range. Push qSET(C) to enter the Set mode. Touch the “Band Edge Beep” item of the “F

4、unction” w Set mode. Function Band Edge Beep If the specifi ed item is not displayed, touch Y or Z(D) one or more times to select the page. Touch the desired option to eselect the desired band edge warning beep setting, or to turn OFF the func- tion. OFF: Band edge beep is OFF. ON (Default): When yo

5、u tune into or out of the default amateur bands frequency range, a beep sounds. (default) ON (User): When you tune into or out of a user pro- grammed amateur bands frequency range, a beep sounds. ON (User) SSB, CW and RTTY only) Minimum RF gain Adjustable range Maximum RF gain While rotating the RF

6、gain control, a faint noise may be heard. This comes from the DSP unit and does not indicate an equipment malfunction. Whenusedasasquelchcontrol (RF gain is fi xed at maximum.) Squelch is open. S-meter squelch S-meter squelch threshold Noise squelch threshold (FM/DV modes) ShallowDeep Noise squelch

7、(FM/DV modes) PBTRIT TX / RX PWR AFRF/SQL CLR M-CHBANK RIT TUNER/CALL MENU MIC/RF PWR NB SPEED/PITCH SET QUICK NOTCH DR AUTO TUNERXCS XFC SPEECH MPAD NR P.AMPATT i7100 w q 1PANEL DESCRIPTION 1-3 eTX/RXLED Lights green when the squelch opens, or a signal is received. Lights red when transmitting. rME

8、MORYBANKCONTROLBANK When both the PBT and RIT LEDs are OFF Rotate to select a Memory bank. When the PBT LED (y) lights green (Mode:SSB/CW/RTTY/AM) RotatetoadjustthereceiversIFfjlterpassband width using the DSP circuit. When the RIT LED (u) lights orange Disable this control. tM-CHCONTROLCLEARSWITCHM

9、-CHCLR Push to select the action of the M-CH/BANK con- trols as the Memory/Bank selection, PBT control or RIT control. When the both RIT and PBT LEDs are OFF Rotate to select a Memory channel. When the RIT LED lights orange RotatetoadjusttheRITfrequencyshift. Thefrequencyshiftrangeis9.99kHzin10Hz st

10、eps. The control tunes in 1 Hz steps when the op- erating frequency readout is set to the 1 Hz step. Hold down for 1 second to clear the RIT shift frequency. What is the RIT function? The RIT (Receiver Incremental Tuning) shifts the re- ceive frequency without shifting the transmit frequency. This i

11、s useful for fi ne tuning stations calling you off-fre- quency, or when you prefer to listen to slightly different- sounding voice characteristics. When the PBT LED lights green (Mode:SSB/CW/RTTY/AM) RotatetoadjustthereceiversIFfjlterpass- band width using the DSP circuit. Hold down for 1 second to

12、reset the PBT set- tings. ThePBTisadjustablein50HzstepsintheSSB/ CW/RTTY modes, and 200 Hz in the AM mode. At that time, the shift value changes in 25 Hz steps in the SSB/CW/RTTY modes, and 100 Hz in the AM mode. ThePBTcontrolsfunctionasanIFshiftcontrol. What is the PBT control? The PBT function ele

13、ctronically modifi es the IF pass- bandwidthtorejectinterference.Thistransceiveruses the DSP circuit for the PBT function. yPBTLED Lights green when the M-CH/BANK controls act as the PBT control. PushtheM-CH switch to select PBT control. uRITLED Lights orange when the RIT function is turned ON. Ligh

14、ts orange when the M-CH/BANK controls act as the RIT control. PushtheM-CH switch to select RIT control. The RIT control is the inner control. The outer control is disabled. iRITKEYRIT (p. 5-4) Push to turn the RIT function ON or OFF. UsetheM-CH control to vary the RIT frequency. Hold down for 1 seco

15、nd to add the shift frequency of the RIT function to, or subtract it from, the dis- played frequency. Controller Front panel (Continued) PBTRIT TX / RX PWR AFRF/SQL CLR M-CHBANK RIT TUNER/CALL MENU MIC/RF PWR NB SPEED/PITCH SET QUICK NOTCH DR AUTO TUNERXCS XFC SPEECH MPAD NR P.AMPATT i7100 t e r y u

16、 i 1PANEL DESCRIPTION 1-4 oANTENNATUNER/CALLKEYTUNER/CALL ANTENNA TUNER KEY Operation (p. 16-4) (Frequencyband:HF/50MHz) Push to turn an optional automatic antenna tuner ON or OFF (bypass). Hold down for 1 second to manually tune the antenna tuner. Ifthetunercannottunetheantennawithin20sec- onds, th

17、e tuning circuit is automatically bypassed. CALL KEY Operation (p. 11-4) (Frequencyband:144/430MHz) Push to select the Call channel. In the 70 MHz band, push to sound an error beep. !0MENUKEYMENU (p. 1-11) Push to change the set of functions assigned to the touch keys. Togglesthefunctiondisplaymenub

18、etweenM-1,M-2and M-3 menus or D-1 and D-2 menus. !1 MICGAIN/RFPOWERADJUSTMENTKEY MIC/RF PWR (p. 3-24) PushtoopentheMICgain/RFpoweradjustment display. RotateM-CHtoadjusttheMICgain. RotateBANKtoadjusttheRFpower. FrequencybandRF output power range HF/50 MHz2 to 100 W (AM: 1 to 30 W) 70 MHz*2 to 50 W (A

19、M: 1 to 15 W) 144 MHz2 to 50 W 430 MHz2 to 35 W Pushagaintoclosethewindow. !2NOISEBLANKERKEYNB (p. 5-8) (Mode:SSB/CW/RTTY/AM) Push to turn the noise blanker ON or OFF. The noise blanker reduces pulse-type noise such as that generated by vehicle ignition systems. The noise blanker is not effective fo

20、r non-pulse-type noise. “NB”appearswhenthenoiseblankerisON. Hold down for 1 second to display the “NB” screen. Push to return to the previous screen. !3 KEYSPEED/CWPITCHADJUSTMENTKEY SPEED/PITCH (pp. 4-4, 6-4) PushtoopentheKeyspeed/CWpitchadjustment display. RotateM-CHtoadjustthekeyingspeedoftheinte

21、r- nal electronic CW keyer to between 6 wpm (minimum) and 48 wpm (maximum). RotateBANK to shift the received CW audio pitch and the CW sidetone pitch without changing the operat- ing frequency. TheCWpitchcanbeadjustedfrom300to900Hzinap- proximately 5 Hz steps. Pushagaintoclosethewindow. !4 NOISEREDU

22、CTIONKEYNR (p. 5-9) Push to turn DSP noise reduction ON or OFF. “NR”appearswhennoisereductionisON. Hold down for 1 second to display the “NR” screen. Push to return to the previous screen. Rotate the Dial to adjust the DSP noise reduction level. Set for maximum readability. Controller Front panel (C

23、ontinued) * 70 MHz band transmission is available, depending on the transceiver version. PBTRIT TX / RX PWR AFRF/SQL CLR M-CHBANK RIT TUNER/CALL MENU MIC/RF PWR NB SPEED/PITCH SET QUICK NOTCH DR AUTO TUNERXCS XFC SPEECH MPAD NR P.AMPATT i7100 o!0!2!4!1!3 1PANEL DESCRIPTION 1-5 !5 PREAMPATTENUATORKEY

24、P.AMPATT PREAMP KEY Operation (p. 5-2) (Frequencyband:HF,50/70MHz) Push to select one of two receive RF preampli- fi ers, or to bypass them. “P.AMP1”isawidedynamicrangepreamplifjer.Itis most effective for the 1.8 to 21 MHz bands. “P.AMP2”isahigh-gainpreamplifjer.Itismosteffec- tive for the 24 to 70

25、MHz bands. Noindicatorappearswhenthepreamplifjersarenot selected. What is the preamplifi er? The preamplifi er amplifi es signals in the front end to improve the S/N ratio and sensitivity. Select “P. AMP1” or “P. AMP2” when receiving weak sig- nals. (Frequencyband:144/430MHz) Push to turn the preamp

26、lifi er ON or OFF. “P.AMP”appearswhenthepreamplifjerisON. ATTENUATOR KEY Operation (p. 5-2) Hold down for 1 second to turn ON the attenu- ator. “ATT”appearswhentheattenuatorisON. Push to turn OFF the attenuator. “ATT”disappears. What is the attenuator? The attenuator prevents a desired signal from b

27、e- ing distorted when very strong signals are near it, or when very strong electromagnetic fi elds, such as from a broadcasting station, are near your lo- cation. !6NOTCHKEYNOTCH (p. 5-10) (Mode=Autonotch:SSB/AM/FM Manualnotch:SSB/CW/RTTY/AM) In the SSB and AM modes, push to toggle the notch functio

28、n between auto, manual and OFF. EithertheAutoorManualnotchfunctioncanbeturned OFF in the “NOTCH Switch (SSB)/(AM)” items of the “Function” Set mode. (p. 17-21) SET Function NOTCH Switch (SSB) SET Function NOTCH Switch (AM) In the FM mode, push to turn the Auto Notch func- tion ON or OFF. In the CW o

29、r RTTY mode, push to turn the Manual Notch function ON or OFF. “MN” appears when the Manual Notch function is ON. “AN”appearswhentheAutoNotchfunctionisON. NoindicatorappearswhenthenotchfjlterisOFF. Hold down for 1 second to display the “NOTCH” screen. Push to return to the previous screen. Rotatethe

30、Dialtoadjustthenotchfrequencytoreject an interfering signal when the manual function is ON. Notchfjltercenterfrequency: SSB/RTTY: 1040 Hz to +4040 Hz CW: CW pitch frequency 2540 Hz to CW pitch frequency +2540 Hz AM: 5060 Hz to +5100 Hz What is the notch fi lter? The notch fi lter is a narrow fi lter

31、 that eliminates un- wanted CW or AM carrier tones, while preserving the desired voice signal. The DSP circuit automati- callyadjuststhenotchfrequencytoeffectivelyelimi- nate unwanted tones. Controller Front panel (Continued) PBTRIT TX / RX PWR AFRF/SQL CLR M-CHBANK RIT TUNER/CALL MENU MIC/RF PWR NB

32、 SPEED/PITCH SET QUICK NOTCH DR AUTO TUNERXCS XFC SPEECH MPAD NR P.AMPATT i7100 !6!5 1PANEL DESCRIPTION 1-6 !7DRMODEKEYDR (section 7,8,9) Push to select the DR mode. WhentheDRmodeisselected,thetransceiverauto- matically selects the DV mode. In the DR mode, push to cancel it. Thetransceiverreturnstot

33、hepreviousscreenbefore entering the DR mode. !8SETMODEKEYSET (section 17) Push to enter or exit the SET mode. “VoiceMemo,”“CallSign,”“RXHistory,”“DVMemory,” “My Station,” “DV Set,” “GPS,” “SPEECH,” “QSO/RX Log,” “Function,” “Tone Control,” “Connectors,” “Dis- play,” “Time Set,” “SD Card” and “Others

34、” set group are selectable. !9QUICKMENUKEYQUICK Push to open or close the Quick Menu window. TheQuickMenuisusedtoquicklyselectvarious functions. In the setting screen, push to open the Default set window. Touch“Default”toresettothedefaultsetting. 0AUTOTUNERXCSKEYAUTO TUNERXCS AUTO TUNE KEY Operation

35、 (p. 4-5) (Mode:CW) Push to automaticallyadjustforazerobeat with the received signal. Zero beat means that two signals are exactly the same frequency. “AUTOTUNE”blinkswhentheautotunefunction is activated. WhentheRITfunctionisON,theautotunefunc- tion changes the RIT frequency, not the displayed frequ

36、ency. RX CALL SIGN CAPTURE KEY Operation (p. 8-7) (Mode:DV,whentheDRmodeisselected) Push to open the “RXCS” screen. Push again to return to the previous screen. Hold down for 1 second to set the received call signs (station and repeaters) as the operating call sign. 1 TRANSMITFREQUENCYCHECKKEYXFC Du

37、ring split frequency or repeater operation, hold down to listen to the transmit frequency. (p. 4-28) Whileholdingdownthisswitch,thetransmitfrequen- cy can be changed with the Dial or MPAD. WhentheSplitLockfunctionisturnedONintheSplit operation, hold down XFC to cancel the Dial lock function. (p. 6-1

38、0) When operating simplex, hold down to monitor the frequency. Whileholdingdownthiskey,thesquelchisopenand theinterferencerejectfunctionsaretemporarilyturned OFF. When operating simplex and the RIT function is turned ON, hold down to listen to the transmit fre- quency. The frequency is the same as w

39、hen the RIT is OFF. In the DV mode, hold down this key to select the RX monitoring mode. (p. 17-13) Controller Front panel (Continued) PBTRIT TX / RX PWR AFRF/SQL CLR M-CHBANK RIT TUNER/CALL MENU MIC/RF PWR NB SPEED/PITCH SET QUICK NOTCH DR AUTO TUNERXCS XFC SPEECH MPAD NR P.AMPATT i7100 !80!71!9 1P

40、ANEL DESCRIPTION 1-7 2SPEECHLOCKKEYSPEECH SPEECH KEY Operation (p. 3-20) Push to audibly announce the S-meter level, the displayed frequency and the operating mode. TheS-LevelannouncementcanbeturnedOFFinthe “S-Level SPEECH” item of the “SPEECH” Set mode. (p. 17-15) SET SPEECH S-Level SPEECH WhenRITi

41、sON,theRIToffsetisnotincludedinthe frequency announcement. LOCK KEY Operation (p. 5-12) Hold down for 1 second to turn the Lock function ON or OFF. ThefunctionelectronicallylockstheDial. “” appears when the function is ON. YoucanselecttheDiallockandPanellockinthe “Lock Function” item of the “Functio

42、n” Set mode. (p. 17-20) SET Function Lock Function NOTE: The SPEECH/LOCK key operation to ac- tivate the voice synthesizer or the Lock functions can be replaced in the “SPEECH/LOCK Switch” item of the “Function” Set mode. (p. 17-20) SET Function Lock Function 3MEMOPADKEYMPAD (p. 11-13) Push to seque

43、ntially call up the contents from the memo pad. The 5 (or 10) most recently programmed frequen- cies and operating modes can be recalled, start- ing from the most recent. Thememopadcapacitycanbeincreasedfrom5to 10 in the “Memopad Numbers” item of the “Function” Set mode (p. 17-20) SET Function Memop

44、ad Numbers Hold down for 1 second to write the displayed data into a memo pad. The5mostrecententriesremaininthememopad. 4MAINDIAL Rotate to change the displayed frequency, select the Set mode settings, and so on. 5MAINDIALTENSIONLATCH Select the Dial drag. Threepositionsareselectable.Thetopsettingtu

45、rnson clicks as the dial is turned. Controller Front panel (Continued) PBTRIT TX / RX PWR AFRF/SQL CLR M-CHBANK RIT TUNER/CALL MENU MIC/RF PWR NB SPEED/PITCH SET QUICK NOTCH DR AUTO TUNERXCS XFC SPEECH MPAD NR P.AMPATT i7100 2 3 4 5 1PANEL DESCRIPTION 1-8 q TX ICON Indicates either the displayed fre

46、quency can be transmitted, or not. “” appears while the operating frequency is in an amateur band. “” appears while the operating frequency is not in an amateur band. However, when the “Band Edge Beep” item is set to “OFF” in the “Function” Set mode (p. 17-18), “” does not appear. SET Function Band

47、Edge Beep “LMT” appears while the output power is de- creased because the Power FETs temperature is high. “HOT” appears while transmission is inhibited be- cause the Power FETs temperature is too high. w MODE ICONS (p. 3-17) Displays the selected operating mode. “-D”appearswhenSSBdata,AMdataorFMdata

48、 mode is selected. Touch to enter the Mode selection screen. OntheModeselectionscreen,touchtheblocktose- lect the operating mode. e PASSBAND WIDTH ICON (pp. 5-5, 5-6) Graphically displays the passband width for twin PBT operation and the center frequency for IF shift operation. rTONESQUELCH/DIGITALS

49、QUELCHICONS (Mode:FM) “TONE” appears when the repeater tone function is ON. (p. 4-25) “TSQL” appears when the tone squelch function is ON. (p. 4-22) “DTCS” appears when the DTCS function is ON. (p. 4-23) (Mode:DV) “DSQL” appears when the digital call sign squelch function is ON. (p. 9-22) “CSQL” appears when digital code squelch func- tion is ON. (