IC-7100_user.pdf

《IC-7100_user.pdf》由会员分享，可在线阅读，更多相关《IC-7100_user.pdf（96页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL i7100 HF/VHF/UHF ALL MODE TRANSCEIVER This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference tha

2、t may cause undesired operation. WARNING: MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBITED UNDER FCC RULES AND FEDERAL LAW. i FOREWORD Thank you for purchasing this fi ne Icom product. The IC-7100 HF/VHF/UHF ALL MODE TRANSCEIVER is designed and build with

3、Icoms superior technology and craftsmanship combining tra- ditional analog technologies with the new digital technology, Digital Smart Technologies for Amateur Radio (D-STAR), for a balanced package. With proper care, this product should provide you with years of trouble-free operation. We thank you

4、 for making your IC-7100 your radio of choice, and hope you agree with Icoms philosophy of “technology fi rst.” Many hours or research and development went into the design of your IC-7100. FEATURES IF DSP features All mode capability covering 1602 m and 70 cm (depending on version) Compact with sepa

5、rated front panel 0.5 ppm of high frequency stability Baudot RTTY demodulator Selectable SSB transmission passband width (For both higher and lower pass frequency) Standard voice synthesizer/voice recorder SD card slot ready for several memory storage Voice recorder to records your communication DV

6、mode (Digital voice + Low-speed data communication) operation-ready Text message and call sign exchange Transmit position data DR (D-STAR Repeater) mode and repeater list allow you to easily operate using a D-STAR repeater EXPLICIT DEFINITIONS WORDDEFINITION R DANGER! Personal death, serious injury

7、or an ex- plosion may occur. R WARNING! Personal injury, fire hazard or electric shock may occur. CAUTIONEquipment damage may occur. NOTE Recommended for optimum use. No risk of personal injury, fi re or electric shock. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transc

8、eiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains important operating instructions for the IC-7100. FCC INFORMATION FORCLASSBUNINTENTIONALRADIATORS: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rule

9、s. These limits are designed to provide reasonable protection against harmful interference in a residential instal- lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radi

10、o communications. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equip- ment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correc

11、t the inter- ference by one or more of the following measures: Reorientorrelocatethereceivingantenna. Increasetheseparationbetweentheequipmentandre- ceiver. Connecttheequipmentintoanoutletonacircuitdifferent from that to which the receiver is connected. Consultthedealeroranexperiencedradio/TVtechnic

12、ian for help. Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/ or other countries. Spurious signals may be received near some frequen- cies. These are created in the internal

13、circuit and does not indicate a transceiver malfunction. CAUTION: Changes or modifi cations to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regula- tions. “AI” means “Advanced Instructions.” “sec. MM” means section number. So when “(AI

14、sec. MM)” is described on this manu- al, see the PDF type Advanced Instructions section number for your reference. ii PRECAUTIONS R DANGER HIGH VOLTAGE! NEVER touch an an- tenna or internal antenna connector during transmission. This may result in an electrical shock or burn. R WARNING RF EXPOSURE!

15、This device emits Radio Frequency (RF) energy. Extreme caution should be observed when operating this device. If you have any questions regarding RF exposure and safety stan- dards please refer to the Federal Communications Commission Offi ce of Engineering and Technologys report on Evaluating Compl

16、iance with FCC Guidelines for Human Radio Frequency Electromagnetic Fields (OET Bulletin 65). R WARNING! NEVER operate the transceiver while driving a vehicle. Safe driving requires your full attention anything less may result in an accident. R WARNING! NEVER operate the transceiver with an earphone

17、, headphones or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume level or discon- tinue use. R WARNING! NEVER apply AC power to the DC13.8V connector on the transceiver rear pan

18、el. This could cause a fi re or damage the transceiver. R WARNING! NEVER apply more than 16 V DC to the DC13.8V connector on the transceiver rear panel or use re- verse polarity. This could cause a fi re or damage the trans- ceiver. R WARNING! NEVER cut the DC power cable between the DC plug and fus

19、e holder. If an incorrect connection is made after cutting, the transceiver might be damaged. R WARNING! NEVER let metal, wire or other objects touch any internal part or connectors on the rear panel of the transceiver. This may result in an electric shock or this could cause a fi re or damage the t

20、ransceiver. R WARNING! NEVER operate or touch the trans- ceiver with wet hands. This may result in an electric shock or may damage the transceiver. R WARNING! Immediately turn the transceiver power OFF and remove the power cable if it emits an abnormal odor, sound or smoke. Contact your Icom dealer

21、or dis- tributor for advice. CAUTION: NEVER expose the transceiver to rain, snow or any liquids. CAUTION: NEVER change the internal settings of the transceiver. This may reduce transceiver perfor- mance and/or damage to the transceiver. DO NOT operate the transceiver near unshielded elec- trical bla

22、sting caps or in an explosive atmosphere. DO NOT use harsh solvents such as benzine or al- cohol to clean the transceiver, as they will damage the transceivers surfaces. If the transceiver becomes dusty or dirty, wipe it clean with a soft, dry cloth. DO NOT use or place the transceiver in areas with

23、 tem- peratures below 10C (+14F) or above +60C (+140F). Be aware that temperatures on a vehicles dashboard can ex- ceed +80C (+176F), resulting in permanent damage to the transceiver if left there for extended periods. DO NOT place the transceiver in excessively dusty environ- ments or in direct sun

24、light. DO NOT place the transceiver against walls or putting any- thing on top of the transceiver. This will obstruct heat dissipa- tion. Place the transceiver in a secure place to avoid inadvertent use by children. During mobile operation, NEVER place the transceiver where air bag deployment may be

25、 obstructed. During mobile operation, DO NOT place the transceiver where hot or cold air blows directly onto it. During mobile operation, DO NOT operate the transceiver without running the vehicles engine. When the transceivers power is ON and your vehicles engine is OFF, the vehicles battery will s

26、oon become exhausted. Make sure the transceiver power is OFF before starting the vehicle engine. This will avoid possible damage to the trans- ceiver by ignition voltage spikes. During maritime mobile operation, keep the transceiver and microphone as far away as possible from the magnetic navi- gati

27、on compass to prevent erroneous indications. BECAREFUL! The rear panel will become hot when op- erating the transceiver continuously for long periods of time. BECAREFUL! If a linear amplifi er is connected, set the transceivers RF output power to less than the linear ampli- fi ers maximum input leve

28、l, otherwise, the linear amplifi er will be damaged. Use Icom microphones only (supplied or optional). Other manufacturers microphones have different pin assignments, and connection to the IC-7100 may damage the transceiver. iii e SUPPLIED ACCESSORIES The following accessories are supplied with the

29、transceiver. q Hand microphone . 1 w Control cable . 1 e Ferrite EMI fi lter .1 For European versions .2 r 3.5 (d) mm plug .1 t ACC cable .1 y DC power cable* (OPC-1457) . 1 or (OPC-2095) . 1 u Spare fuse (ATC 5 A) . 1 i USB cable .1 o CD .1 !0 Spare fuse (ATC 30 A) . 2 * Depending on the version. q

30、 we r t y y u i o !0 ABOUT THE SUPPLIED CD The following instructions and installers are included on the CD. Basicinstructions Instructions for the basic operations, the same as this manual AdvancedInstructions Instructions for the advanced operations and more details are described than in this manu

31、al Schematicdiagram Includes the schematic and block diagrams HAMradioTerms A glossary of HAM radio terms AdobeReaderInstaller Installer for Adobe Reader A PC with the following Operating System is required. Microsoft Windows 8, Microsoft Windows 7 , Mi- crosoft Windows Vista or Microsoft Windows XP

32、 StartingtheCD D Insert the CD into the CD drive. q Doubleclick“Autorun.exe”ontheCD. DependingonthePCsetting,theMenuscreenshown below is automatically displayed. Click the desired button to open the fi le. w ToclosetheMenuscreen,clickQuit. To read the guide or instructions, Adobe Reader is required.

33、 If you have not installed it, please install the Adobe Reader on the CD or downloaded it from Ado- be Systems Incorporateds website. QuitsthemenuscreenInstalls the Adobe Reader Opens the Glossary Opens the Basic Instructions (this manual) Opens the Advanced Instructions Opens the Schematic diagram

34、(See p. 2-7 for installation details) For European versions ControllerFrontpanel .1-2 ControllerFunctiondisplay .1-7 ControllerMulti-functionkeys .1-10 M-1 (M-1 menu) Display D .1-10 M-2 (M-2 menu) Display D .1-10 M-3 (M-3 menu) Display D .1-10 D-1 (D-1 menu) Display D .1-10 D-2 (D-2 menu) Display D

35、 .1-10 Function keys on M-1 display D .1-10 Function keys on M-2 display D .1-10 Function keys on M-3 display D .1-11 Function keys on D-1 display D .1-12 Function keys on D-2 display D .1-12 ControllerRearandbottompanels .1-13 MainunitFrontpanel .1-14 MainunitRearpanel .1-14 ACC socket information

36、D .1-16 DATA2 socket information D .1-17 Microphone connector information D .1-17 Microphone .1-18 HM-198 (Supplied) D .1-18 SM-50 D(Option) .1-18 SM-30 D(Option) .1-18 HM-151 D(Option).1-19 Section1PANEL DESCRIPTION Section2INSTALLATIONANDCONNECTIONS Section3BASICOPERATION Section4D-STAR INTRODUCTI

37、ON Section5D-STAROPERATION Section6SETMODE Section7 INSTALLATION NOTES 1-1 Section1PANEL DESCRIPTION 1-1 “AI” means “Advanced Instructions.” “sec. MM” means section number. So when “(AI sec. MM)” is described on this manual, see the PDF type Advanced Instructions section number for your reference. 1

38、PANEL DESCRIPTION 1-2 ControllerFrontpanel q POWERSWITCHAFVOLUMEPWRAF (p. 3-2) Push to turn ON the transceiver power. First,confjrmtheDCpowersourceisturnedON. Hold down for 1 second to turn OFF the power. Rotate to adjust the audio output level. Increases Decreases w RF GAIN CONTROL/ SQUELCH CONTROL

39、 RF/SQL (p. 3-19) Rotate to adjust the RF gain and squelch threshold levels. The squelch removes noise output to the speaker when no signal is received. (closed condition) ThesquelchisparticularlyeffectiveforAMandFM,but also works in other modes. The12to1oclockpositionisrecommendedforthemost effecti

40、veuseoftheRF/SQLcontrol. RF/SQLoperatesasonlyanRFgaincontrolinSSB, CW and RTTY (Squelch is fi xed open), or a squelch con- trol in AM, FM, WFM and DV (RF gain is fi xed at maxi- mum sensitivity),when“Auto”isselectedasthe“RF/SQL Control” item in the “Function” Set mode. (p. 6-5) SET Function RF/SQL C

41、ontrol WhenusedasanRFgain/squelchcontrol Maximum RF gain S-meter squelch Noise squelch (FM/DV modes) Squelch is open. RF gain adjustable range Recommended level WhenusedasanRFgaincontrol (Squelch is fi xed open; SSB, CW and RTTY only) Minimum RF gain Adjustable range Maximum RF gain While rotating t

42、he RF gain control, a faint noise may be heard. This comes from the DSP unit and does not indicate an equipment malfunction. Whenusedasasquelchcontrol (RF gain is fi xed at maximum.) Squelch is open. S-meter squelch S-meter squelch threshold Noise squelch threshold (FM/DV modes) ShallowDeep Noise sq

43、uelch (FM/DV modes) PBTRIT TX / RX PWR AFRF/SQL CLR M-CHBANK RIT TUNER/CALL MENU MIC/RF PWR NB SPEED/PITCH SET QUICK NOTCH DR AUTO TUNERXCS XFC SPEECH MPAD NR P.AMPATT i7100 w q e y u io!0!1 t r 1PANEL DESCRIPTION 1-3 e TX/RX LED Lights green when the squelch opens, or a signal is received. Lights red when transmitting. rMEMORYBANKCONTROLBANK When both the PBT and RIT LEDs are OFF Rotate to select a Memory bank. When the PBT LED (y) lights green (Mode:SSB/CW/RTTY