IC-9700_basic_user.pdf

《IC-9700_basic_user.pdf》由会员分享，可在线阅读，更多相关《IC-9700_basic_user.pdf（100页珍藏版）》请在收音机爱好者资料库上搜索。

1、BASIC MANUAL |9700 VHF/UHF ALL MODE TRANSCEIVER i Thank you for choosing this Icom product. The IC-9700 VHF/UHF ALL MODE TRANSCEIVER is designed and built with Icoms state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation.

2、 We appreciate you making the IC-9700 your transceiver of choice, and hope you agree with Icoms philosophy of “technology fjrst.” Many hours of research and development went into the design of your IC-9700. FEATURES RF Direct Sampling System The IC-9700 employs an RF direct sampling system. RF signa

3、ls are directly converted to digital data in the ADC, and then processed in the FPGA. This system is a leading technology, marking an epoch in amateur radio. The 1200 MHz band uses a downconversion IF sampling. Real-Time Spectrum Scope The spectrum scope is class-leading in resolution, sweep speed a

4、nd dynamic range. When you touch the scope screen on the intended signal, the touched area is magnifjed. The large 4.3 inch color TFT touch LCD ofgers intuitive operation. D-STAR operation The IC-9700 has the D-STAR Repeater (DR) function. Moreover, by using the DD mode, you can browse the Internet

5、through a repeater station. Satellite operation The IC-9700 has 99 satellite memory channels for both uplink and downlink frequencies and mode. “IP+” Function The IP Plus function improves 3rd order intercept point (IP3) performance. When a weak signal is received adjacent to strong interference, th

6、e AD converter is optimized against signal distortion. A 4.3 inch touch panel color display Multi-function control for easy settings SUPPLIED ACCESSORIES L Difgerent types of accessories may be supplied, or may not be supplied depending on the transceiver version. WORDDEFINITION R DANGER! Personal d

7、eath, serious injury or an explosion may occur. R WARNING! Personal injury, fjre hazard or electric shock may occur. CAUTIONEquipment damage may occur. NOTE Recommended for optimum use. No risk of personal injury, fjre or electric shock. EXPLICIT DEFINITIONSIMPORTANT READ ALL INSTRUCTIONS carefully

8、completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL This instruction manual contains basic operating instructions for the IC-9700. For advance operating instructions, see the Advanced Manual for details. The Advance Manual is available at the following internet address: http:/www.i

9、com.co.jp/world/support/ Hand microphone DC power cable (3 m: 9.8 ft) Spare fuse (25 A) Spare fuse (5 A) CW key plug (3.5 mm: 1/8 Stereo) This product includes RTOS “RTX” software, and is licensed according to the software license. This product includes “zlib” open source software, and is licensed a

10、ccording to the open source software license. This product includes “libpng” open source software, and is licensed according to the open source software license. Refer to the “About the Licenses” page at the end of this manual for information on the open source software being used in this product. T

11、his software is based in part on the work of the Independent JPEG Group, and is licensed according to the open source software license. ii This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

12、to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, ther

13、e is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment ofg and on, the user is encouraged to try to correct the interference by one or more o

14、f the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit difgerent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for hel

15、p. CAUTION: Changes or modifjcations to this device, not expressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. The crossed-out wheeled-bin symbol on your product, literature, or packaging reminds you that in the European Union, all electrical and el

16、ectronic products, batteries, and accumulators (rechargeable batteries) must be taken to designated collection locations at the end of their working life. Do not dispose of these products as unsorted municipal waste. Dispose of them according to the laws in your area. FCC INFORMATION Icom is not res

17、ponsible for the destruction, damage to, or performance of any Icom or non-Icom equipment, if the malfunction is because of: Force majeure, including, but not limited to, fjres, earthquakes, storms, fmoods, lightning, or other natural disasters, disturbances, riots, war, or radioactive contamination

18、. The use of Icom transceivers with any equipment that is not manufactured or approved by Icom. TRADEMARKS Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia, Australia, New Zealand

19、and/or other countries. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and/or other countries. Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries. AMBE+2 is

20、 a trademark and property of Digital Voice Systems Inc. All other products or brands are registered trademarks or trademarks of their respective holders. Hereby, Icom Inc. declares that the versions of IC-9700 which have the “CE” symbol on the product, comply with the essential requirements of the R

21、adio Equipment Directive, 2014/53/EU, and the restriction of the use of certain hazardous substances in electrical and electronic equipment Directive, 2011/65/EU. The full text of the EU declaration of conformity is available at the following internet address: http:/www.icom.co.jp/world/support/ DIS

22、POSAL ABOUT CE AND DOC iii The AMBE+2 voice coding Technology embodied in this product is protected by intellectual property rights including patent rights, copyrights and trade secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed solely for use within this Communications

23、Equipment. The user of this Technology is explicitly prohibited from attempting to extract, remove, decompile, reverse engineer, or disassemble the Object Code, or in any other way convert the Object Code into a human-readable form. U.S. Patent Nos. #8,595,002, #8,359,197, #8,315,860, #8,200,497, #7

24、,970,606, #6,912,495 B2. VOICE CORDING TECHNOLOGY D Touch operation In the Advanced manual or Basic manual, the touch operation is described as shown below, with the beep tone ON. Touch If the display is touched briefmy, one short beep sounds. Touch for 1 second If the display is touched for 1 secon

25、d, one short and one long beep sound. D Touch screen precautions The touch screen may not properly work when the LCD protection fjlm or sheet is attached. Touching the screen with your fjnger nails, sharp topped object and so on, or touching the screen hard may damage it. Tablet PC operations such a

26、s fmick, pinch in and pinch out cannot be performed on this touch screen. D Touch screen maintenance If the touch screen becomes dusty or dirty, wipe it clean with a soft, dry cloth. When you wipe the touch screen, be careful not to push it too hard or scratch it with your fjnger nails. Otherwise yo

27、u may damage the screen. The following manuals or Guide for this transceiver are published at the following internet address: http:/www.icom.co.jp/world/support/ Advanced Manual (English) Instructions for advanced operations in English. Basic Manual (English) Instructions for basic operations, the s

28、ame as this manual. Basic Manual (Multi-language) Instructions for basic operations in multiple languages. CI-V Reference Guide (English) Describes the control commands used in remote control operation (serial communication with CI-V). About the Share Pictures function (English) Describes how to use

29、 the Share Pictures function in English. For Reference HAM Radio Terms (English) A glossary of HAM radio terms in English. A PC with the following Operating System is required. Microsoft Windows 10 Microsoft Windows 8.1 Microsoft Windows 7 To read the manuals or Guide, Adobe Acrobat Reader is requir

30、ed. If you have not installed it, please down load the Adobe Acrobat Reader and install it to your PC. You can download it from Adobe Systems Incorporateds website. ABOUT THE TOUCH SCREENABOUT THE MANUALS iv ABOUT THE INSTRUCTIONS Instruction example MENU SET Display Display Type Detailed instructio

31、n 1. Push MENU. Push Opens the MENU screen. 2. Touch SET. MENU screen Opens the SET screen. 3. Rotate MULTI, and then push MULTI to select “Display.” Rotate Push 4. Rotate MULTI, and then push MULTI to select “Display Type.” SET screen Rotate Push The Advanced and Basic manuals are described in the

32、following manner. “ ” (Quotation marks): Used to indicate icons, setting items, and screen titles displayed on the screen. The screen titles are also written in uppercase letters. (Example: FUNCTION screen) (brackets): Used to indicate keys. Routes to the Set modes and Setting screens Routes to the

33、Set mode, Setting screens and the setting items are described in the following manner. DISPLAY screen “Display Type” screen v TABLE OF CONTENTS IMPORTANT . i FEATURES . i EXPLICIT DEFINITIONS . i SUPPLIED ACCESSORIES . i FCC INFORMATION .ii ABOUT CE AND DOC .ii DISPOSAL .ii TRADEMARKS .ii ABOUT THE

34、TOUCH SCREEN .iii VOICE CORDING TECHNOLOGY .iii ABOUT THE MANUALS .iii ABOUT THE INSTRUCTIONS .iv PRECAUTIONS .vii 1 PANEL DESCRIPTION 1-1 Front panel .1-1 Rear panel .1-3 Touch screen display .1-4 DFUNCTION screen .1-6 DMENU screen .1-6 DQUICK MENU .1-6 DMulti-function menus .1-7 Multi-function dia

35、l .1-7 Keyboard entering and editing .1-8 DEntering and editing characters .1-8 DKeyboard types .1-9 DEntering and editing .1-9 DEntering and editing example .1-10 2 INSTALLATION AND CONNECTIONS 2-1 Selecting a location .2-1 Using the desktop stands .2-1 Connecting an external DC power supply .2-1 H

36、eat dissipation .2-1 Grounding .2-1 3 BASIC OPERATION 3-1 When fjrst applying power .3-1 Turning power ON or OFF .3-1 Adjusting the volume level .3-1 Selecting the VFO and Memory modes .3-1 Using the VFO mode .3-1 DSelecting VFO A or VFO B .3-1 DEqualizing VFO A and VFO B .3-1 Dualwatch operation .3

37、-2 Selecting the Main and Sub bands .3-2 DSwapping the Main band and Sub band .3-2 Selecting the operating band .3-3 DUsing the band stacking registers .3-3 Selecting the operating mode .3-3 Setting the frequency .3-4 DUsing the Main Dial .3-4 DAbout the Tuning Step function .3-4 DChanging the Tunin

38、g Step .3-4 D About the 1 MHz Step Tuning function .3-4 D About the 1 Hz step Fine Tuning function .3-4 DAbout the 1/4 Tuning function .3-5 DAbout the Auto Tuning Step function .3-5 DDirectly entering a frequency .3-5 DBand Edge Beep .3-6 DEntering a Band Edge .3-7 RF gain and SQL level .3-10 Dial L

39、ock function .3-10 Adjusting the transmit output power .3-10 DAdjusting the transmit output power .3-10 Transmit Power Limit function .3-10 Meter display . 3-11 DMeter display selection . 3-11 DMulti-function meter . 3-11 Adjusting the microphone gain . 3-11 4 RECEIVING AND TRANSMITTING 4-1 Preampli

40、fjers .4-1 Attenuator .4-1 RIT function .4-1 D RIT monitor function .4-1 CW Auto Tuning function .4-1 AGC function control .4-2 D Selecting the AGC time constant preset value .4-2 DSetting the AGC time constant .4-2 Using the Digital Twin PBT .4-3 Selecting the IF fjlter .4-4 Selecting the IF fjlter shape .4-4 Noise Blanker .4-5 DAdjusting the NB level and time .4-5 Noise Reduction .4-6 DAdjusting the Noise Reduction level .4-6 Notch Filter .4-6 DSelecting the Notch fjlter type .4-6 DSetting the Manual Notch fjlter .