TS-590S_USB_audio_user.pdf

《TS-590S_USB_audio_user.pdf》由会员分享，可在线阅读，更多相关《TS-590S_USB_audio_user.pdf（17页珍藏版）》请在收音机爱好者资料库上搜索。

1、TS-590S USB Audio Setting Manual October/15/2010 2 Contents 1. About the TS-590S USB Audio Function. 3 2. Operation Using the USB Audio Function . 4 3. Installing the ARUA-10 Software. 5 3.1 System Requirements . 5 3.2 Installation . 5 3.3 About Virtual COM Port Driver. 5 4. Settings. 7 4.1 Transcei

2、ver Settings. 7 4.1.1 Setting Up an Audio Input Route from the Rear Terminal. 7 4.1.2 Audio I/O Level Settings. 7 4.1.3 Mixed Beep Setting to External Audio Outputs. 7 4.1.4 Data VOX Settings. 8 4.1.5 Data VOX Delay Time Setting. 8 4.1.6 Data VOX Gain Setting . 8 4.1.7 Allocating DATA SEND Functions

3、 to PF Keys . 8 4.2. Setting Transmission Methods for Audio Input to the Rear Terminal. 9 4.3 ARUA-10 Settings.10 5. Limitations IMPORTANT！ .12 5.1 USB Port Connectivity Limitations.12 6. Frequently Asked Questions .13 Windows is a registered trademark or trademark of Microsoft Corporation in the Un

4、ited States and other countries. .NET Framework is a registered trademark or trademark of Microsoft Corporation in the United States and other countries. Bluetooth is a registered trademark or trademark of Bluetooth SIG, Inc. The names of all products described hereafter are the trademarks or regist

5、ered trademarks of their respective manufacturers. and are omitted throughout the text. Disclaimer: All efforts have been made regarding the accuracy of the contents described in this document. However, there is a possibility of misprints and of descriptions that may cause misunderstanding. Kenwood

6、Corporation bears absolutely no responsibility for damages arising thereof. Kenwood Corporation may revise and amend the products information described in this document without notice. Kenwood Corporation bears absolutely no responsibility for damages arising thereof. 3 1. About the TS-590S USB Audi

7、o Function When the TS-590S is connected to the computer using a USB cable, the USB audio function can be used to play incoming audio over the computer speakers and transmit audio from the computer microphone. This setup guide explains how to set up the TS-590S to use its USB audio function and how

8、to use the ARUA-10 software to control input/output routes of the USB audio signals from a computer. Important ? USB audio may be delayed due to unavoidable principles. Consequently, do not perform operations (such as contests or pile-ups requiring quick responses) for which delays are likely to be

9、a problem. ? Refer to Chapter 5 “Limitations for other limitations. ? To use the USB audio function, knowledge not only of transceivers but also of computers is required. Kenwood does not offer support for purchasing computers or for customers computers. ? Kenwood Corporation shall bear no responsib

10、ility for related damage such as damage caused by missed communications and dialog opportunities due to incorrect customer settings, nonconformances, or misoperations as a result of using this document or the ARUA-10 software. 4 2. Operation Using the USB Audio Function Operation using the USB audio

11、 function is explained using the diagram below. Diagram 1: Operation Using the USB Audio Function The left side of the diagram shows the TS-590S unit while the area in the square on the right- side indicates the computer. The TS-590S and the computer are connected by a USB cable. The microphone and

12、speakers connected to the computer are shown on the far right. Audio reception is explained first. Incoming audio from the TS-590S is sent to the computer via the USB cable and played over the speakers connected to the computer. A signal pathway on the computer to connect the USB audio device input

13、signals and output from the audio device connected to the speaker is necessary. Audio transmission is explained next. Audio input from the microphone connected to the computer passes through the USB cable and is transmitted by the TS-590S unit. A signal pathway on the computer between input signals

14、from the audio device connected to the microphone and output from the USB audio device is necessary. The ARUA-10 software serves as a bridge for these signal paths within the computer. The ARUA-10 software lets you select which speaker and microphone are used for transceiver operations when there ar

15、e multiple speakers and microphones connected to the computer. 5 3. Installing the ARUA-10 Software 3.1 System Requirements In order to use the ARUA-10 software, your computer must meet the following requirements. Chart 1 - Computer Requirements Category Specifications CPU CPU must exceed performanc

16、e recommended for your operating system MEMORY System memory must exceed that recommended for your operating system HDD Over 100 MB free space CD-ROM/ DVD-ROM Drive Not required USB Port When using the system described above, a single USB 2.0 port Input/Output Devices Keyboard, mouse, microphone, sp

17、eakers Display XGA?1024 768?or above Sound Required OS Windows XP (SP3 or later) Windows Vista (SP1 or later, 32-bit only) Windows 7(32-bit or 64-bit) Not compatible with other operating systems 3.2 Installation Download and install the ARUA-10 software from the following Kenwood website: When conne

18、cting the TS-590S to a computer using a USB cable for the first time, drivers required for the USB Audio Function are automatically installed. If you are using an ARCP-590 and Computer Control Command, you must install the “Virtual COM port driver” to connect the TS-590S with a USB cable. Download a

19、nd install the driver from the following Kenwood website: 3.3 About Virtual COM Port Driver When connecting the TS-590S to a computer with a USB cable for the first time, the “New Hardware Detected Wizard” message appears. This is the install prompt for the Virtual COM Port. 6 If you are not using a

20、n ARCP-590 or Computer Control Command, there is no need to install the Virtual COM Port. However, if it is not installed, the Wizard message appears every time the USB cable is connected, so we recommend installation. When the “New Hardware Detected Wizard” message appears and you have not yet inst

21、alled the Virtual COM Port, click “Cancel” and install the Virtual COM Port before continuing. For details on how to install the Virtual COM Port please visit the download page noted above. 7 4. Settings 4.1 Transceiver Settings Complete the necessary transceiver (TS-590S) settings before using the

22、USB audio function. (Refer to the user manual for how to use the TS-590S.) 4.1.1 Setting Up an Audio Input Route from the Rear Terminal On the rear terminal there are two types of audio input routes the ACC2 connector route and the USB connector route for using the USB audio function. Make the follo

23、wing menu settings to transmit audio input from the USB connector. Menu No. Function Set value 63 Audio input line selection for data communications USB The default setting is ACC2. 4.1.2 Audio I/O Level Settings Use the following menu to adjust audio transmission input levels from the PC, and recei

24、ve audio output levels to the PC. Menu No. Function Setting range 64 Audio level of USB input for data communications 0 to 9 65 Audio level of USB output for data communications 0 to 9 The default value for all settings is 4. 4.1.3 Mixed Beep Setting to External Audio Outputs With the TS-590S defaul

25、t mode, only received audio signals that do not include beeps or side tones are output as audio signals from the ACC2 connector and the USB connector as USB audio signals. Make the following menu settings to output the same audio as the audio output from the wireless speaker, including beeps and sid

26、e tones, externally. Menu No. Function Set value 68 Mixing beep tones for ACC2/USB audio outputs ON The default setting is OFF. 8 Reference: To implement data communications, turn this function OFF. 4.1.4 Data VOX Settings Set whether or not to use the VOX function for the audio output from the rear

27、 terminal. Menu No. Function Set value 69 Data VOX ON or OFF The default setting is OFF. Caution: ? When this function is ON, all sounds created by the computer other than the intended audio transmissions are also transmitted, so be careful. ? When using this function for the first time, we recommen

28、d connecting a dummy load to the TS-590S to perform checks and adjustments. 4.1.5 Data VOX Delay Time Setting Set the VOX Delay Time Setting when using the Data VOX function. Menu No. Function Setting range 70 Data VOX delay time 0 to 100 The default setting is 50. 4.1.6 Data VOX Gain Setting Set th

29、e VOX Gain Setting when using the Data VOX function. Menu No. Function Setting range 71 Data VOX gain for the USB audio input 0 to 9 The default setting is 50. 4.1.7 Allocating DATA SEND Functions to PF Keys Set the DATA SEND functions to the PF keys to test the transmission of audio input from the

30、rear terminal. In this example, the PF A key has been set. Menu No. Function Set value 79 Front panel PF A key assignment 205 The default setting is 200 (VOICE1). 9 Using the PF keys, which set the DATA SEND functions, enables switching between transmit and receive modes for audio input from the rea

31、r terminal. 4.2. Setting Transmission Methods for Audio Input to the Rear Terminal The SEND keys on the PTT of the microphone connected to the TS-590S, and on the TS-590S control panel, are the method for transmitting audio input to the microphone connected to the TS-590S, so even if these operation

32、s are implemented, audio entered as audio signals from USB cannot be transmitted. To transmit audio input as audio signals from the USB, select one of the following methods. Transmitting using the ARCP-590 With the ARCP-590, settings must be done to transmit audio input through the rear terminal to

33、use the on-screen SEND key. Select Setup TX control from the ARCP-590 Tool menu. The Setup TX control window is displayed. In the window above, select ACC2/USB in the Modulation line setting, and then select USB. For further details refer to the ARCP-590 help. (ARCP-590 details are downloadable from

34、 the Kenwood website.) Use the ACC2 Connectors PKS port to transmit. This setting allows you to transmit audio received by the rear terminal by setting the PKS port in the ACC2 Connector on the back of the TS-590S to “Low.” For details of the connector and terminal specifications, refer to the TS-59

35、0S instruction manual. Use the PF key assigned to the DATA SEND function to transmit. By assigning the PF key to the DATA SEND function, the PF key can be used to transmit audio received by the rear terminal For details, refer to 4.1.7 Allocating DATA SEND Functions to PF Keys. 10 4.3 ARUA-10 Settin

36、gs Follow the steps below to set up the ARUA-10 ? Connect the TS-590S and computer using a USB cable. ? To launch the software, select Start Button Programs Kenwood ARUA-10. ? After launching the ARUA-10, a “Task Tray” icon appears. Right click this icon and select “Device Settings” from the menu. T

37、he window shown below appears. In this window you can specify sound devices for the transceivers audio reception output and modulated audio input. You can also specify which microphones and speakers connected to the computer to use. In the above example, the computer has recognized four types of inp

38、ut sound devices. Microphone (USB Audio Codec) Microphone (SoundMAX Integrated Digital Audio) Line In (SoundMAX Integrated Digital Audio) Phone (SoundMAX Integrated Digital Audio) There are two types of output sound devices. Speakers (USB Audio Codec) Speakers (SoundMAX Integrated Digital Audio) * T

39、he items listed depend on the operating system and sound devices used. 11 ? On the far left of the window, from the “Radio” section set the “Reception Output”. This is where the input is set for audio received from the transceiver. As audio reception comes into the computer as USB audio, select “Mic

40、rophone (USB Audio Codec). ? In the second section on the left side of the window, set the “Modulated Input” in the “Radio” section. This is where the output is set for sending audio transmissions to the transceiver. As transmissions are sent to the transceiver as USB audio, select “Speakers (USB Au

41、dio Codec).” ? In the third section from the left side of the window, set the “Microphone” in the “PC” section. This is where the computer microphone used for audio input to be transmitted is set. In the above example, “Microphone (SoundMAX Integrated Digital Audio)” is selected. ? On the far right

42、of the window in the “PC” section, set the “Speakers” device. This is where the computer speakers used for playing incoming audio are specified. Clicking the “RX AF Test” button plays a test signal from the selected speaker. Next, follow the steps below, to confirm that the intended audio transmissi

43、on route is configured. ? Connect the dummy load to the TS-590S. ? If the TS-590S is in Split mode, switch to Simplex mode, with the mode set to SSB (USB or LSB). ? Enable the transmission monitor function. ? Press the PF key set to the DATA SEND function to transmit. ? From the ARUA-10 window shown

44、 above, click the “TX AF Test” button. If test signals are played from the internal TS-590S speakers, the system is set up correctly. Push the PF key set to the DATA SEND function to return to audio reception mode. If the test signal does not play, check the settings and try the test again. ? From the ARUA-10 window, click the “OK” button to complete the setup. ? Right-click on the icon in