TS-590SG_broch.pdf

《TS-590SG_broch.pdf》由会员分享，可在线阅读，更多相关《TS-590SG_broch.pdf（8页珍藏版）》请在收音机爱好者资料库上搜索。

1、HF/50MHz TRANSCEIVER Superior Standards in Performance Incremental changes help performance and function to evolve. An even higher performance receiver with superior adjacent dynamic range. Advanced AGC control through digital signal processing from the IF stage. Highly reliable TX outputs high-qual

2、ity TX signal. New morse code decoder. Scroll display on 13-segment display unit. Characters shown in dedicated window on ARCP-590G. MULTI/CH knob (with push-switch) and RIT/XIT/CL key also configurable in addition to existing PF A and PF B programmable functions. New Split function (TS-990S-style)

3、enabling quick configuration added in addition to existing Split setting. Transceiver equalizer configurable by mode. FIL A/B configurable independently with VFO A/B (convenient during Split operation). Front or rear PTT selectable for Data PTT. Switching from HI CUT/LO CUT to WIDTH/SHIFT possible f

4、or reception bandwidth changing in SSB mode. A Proven Pedigree in Performance The TS - 590SG Be witness to the evolution of KENWOODs pride and joy - the TS-590S HF transceiver - pushing performance and technology to its utmost limit, with the receiver configured to capitalize on roofing filter perfo

5、rmance and IF AGC controlled through advanced DSP technology. Enter the TS-590SG. A new generation of high performance transceiver, with the type of high level response to meet DXers needs. 5 Roofing Filter Interfering signal IF DSP Filter Target Signal AGC DET Demod RX Audio RX IF Analog AGCV SOFT-

6、ATK CONT IF Filter Auto Manual Notch Digital NBIF ADC AGCV DACAGC DET OUT Band ATK/REL Manager AGC DET OUT BAND AGC CONTROL Block diagram: IF AGC control SHIFT Target signal SHIFT If interference is on one side only, you can shift the central frequency without changing bandwidth. IF Auto-Notch WIDTH

7、 Target signal WIDTH You can also avoid an adjacent unwanted signal by varying the passband width. Digital/Analog Noise Blanking (NB1 / NB2) In addition to the analog noise blanker (NB1), which has a proven track record for eliminating weak noise, this transceiver is equipped with a digital noise bl

8、anker (NB2). The optimum blanker for the type of noise and reception conditions can be selected. NB1 enables stable noise suppression independent of reception bandwidth, while NB2 is effective against noise that defies tracking by an analog noise blanker. DSP Noise Reduction (NR1 / NR2) This series

9、features 2 kinds of noise reduction methods: NR1 and NR2. NR1 applies the most optimum kind of noise reduction for each reception mode, while NR2 employs the SPAC method, which is more effective for CW operation. Beat cancel (BC1/BC2) Whereas IF auto notch is effective against a single, powerful bea

10、t, the beat cancel feature works well when there are multiple, weak beats. BC1 is effective to remove weak and/or continuous beat interference, while BC2 is effective for intermittent beats like CW signals. Beat Notch FilterNotch Filter Target Signal A variety of functions realized with 32-bit Float

11、ing-point DSP. Advanced AGC control through digital signal processing from the IF stage onward Other interference/noise removal features Diverse interference/noise removal features When an interfering signal exists in the Roofing Filter passband, and outside the IF DSP Filter band, reception sensiti

12、vity can sometimes be suppressed. In order to avoid this, AGC needs to be made to act on the interfering signal without affecting the target signal. This series has achieved drastic improvements with respect to suppression using unique IF DSP AGC control technology. *1: Available only in SSB mode *2

13、: Available in SSB/CW/FSK modes It would be no exaggeration to say that KENWOODs reception audio, which enjoys a reputation for being non-tiring even in long contests, is determined by IF AGC control based on unique DSP algorithms. This series features all of the IF DSP AGC technology developed with

14、 the TS-990S. A remodeling of the AGC circuitry has realized superb AGC performance covering from small to large inputs. Even if interference signals slip between the Roofing Filter and the IF DSP filter that determines the final selection, level- optimized AGC control enables operation without the

15、need for awareness of Roofing Filter bandwidth. Adjustable IF filter passband This operates as the passband HI CUT/ LO CUT function in SSB/AM/FM modes, and as the WIDTH/SHIFT control function in CW/FSK/SSB-DATA modes. Operation can be switched using the menu in SSB and SSB-DATA modes. IF Notch Remov

16、e a powerful interfering signal with a notch filter to capture a weak target signal. Choose from automatically variable notch frequency in IF Auto-Notch*1 and manually adjustable notch frequency in Manual Notch*2 depending on your interference situation. IF Filter One-touch A/B switching FIL A/B can

17、 be set independently with VFO A/B. This convenient function enables swift operation during contests or split operation. HF / 50MHz TRANSCEIVER TS-590SG erformance refined further in the KENWOOD tradition of HF / 50MHz TRANSCEIVER Output:100W NR1 Spectral-subtraction noise reduction has been develop

18、ed with a focus on improving reception clarity for weak SSB signals. It enables the bringing to the surface of a target signal that is swamped by noise, without any loss in sound quality. For non-speech modes (CW/FSK), a line enhancer offers tried and true noise reduction. Estimated Noise Reduced No

19、ise Target signal NR1: The noise level is estimated and that alone is subtracted, thus emphasizing the target signal. NR2 NR2 is SPAC-based noise reduction that is effective for CW operation as it can suppress noise at the same frequency as the target signal (not available for FM mode). Target signa

20、l is extracted from surrounding noise NR2:SPAC 6 LED backlight with selectable color tone The large display ensures outstanding visibility under all conditions. In addition to conventional amber and green, you can now select intermediate colors and change from amber to green in 10 steps. USB connect

21、or （USB-B） COM connector （D-Sub 9Pin） External speaker jack （3.5mm） ACC2 connector （13Pin DIN） REMOTE connector （7Pin DIN） KEY jack (3.5mm) Paddle jack （6.3mm） Antenna connectors GND terminal AT connector （6Pin） DC power connector （13.8V） RX IN connector （RCA） Drive/Antenna output connector （RCA） Hi

22、ghly reliable TX outputs high-quality TX signal.Diverse functions supporting CW operation. The large display Highly reliable design guarantees stable operation Comfortable CW support Heavy-duty design A pair of 60 x 60 mm fans have been used for the cooling system, which provides sufficient air flow

23、 at low rpm for less noise. Attention has been paid not only to the fans and motors but also to the size and shape of the intake/exhaust vents as a comprehensive approach to quieter operation. The aluminum die-cast chassis is combined with a large heat sink to effectively dissipate heat, minimizing

24、the rise in temperature in the final section during continuous transmission sessions. This heavy-duty design is capable of withstanding grueling conditions typical of contests or long hours of hard operation. Drive output (including 135 kHz band) The transceiver comes equipped with a drive output (D

25、RV) connector that enables external access to the transmission drive output (approx. 0 dBm). This is not just convenient when a transverter is attached; this DRV connector can also be put to use for transmission on the 135 kHz band, for which the main antenna terminal cannot be used. Performance can

26、 be further enhanced when combined with a dedicated reception antenna connector. Morse code decoder function Received morse code displayable by scrolling on 13-segment display unit. Characters are shown in a dedicated window on the ARCP-590G. CW auto-tune You can automatically zero-in on a target si

27、gnal during reception in CW operation with just the press of a button. This function will also tune in to the RIT frequency during RIT operation. 2 key terminals on rear panel An electronic keyer (built-in) paddle terminal and a separate terminal for an external keyer have been included. PC keying i

28、s possible even when a paddle is connected. Other CW features Support for full break-in and semi break-in (semi break-in delay time: 50ms1000ms) Pitch control (3001000Hz) Side tone monitor with 20-step volume control Electronic keyer (selectable key speed, A/B modes) Memory keyer (max. 4-channel mes

29、sage memory) Microphone paddle mode CW reverse mode CW auto transmit function, in which a simple key-press will switch automatically to CW in SSB mode Speech processor (SSB/AM/FM) The speech processor increases the clarity of messages for the receiving station by raising average transmission modulat

30、ion. Besides adjusting compression level, soft and hard modes are available for 2-level adjustment. Compression levels can be set for each of mic transmission and voice-message transmission. Band-adjustable TX filter (SSB/AM) The TX filter passband is switchable. Low-pass and high-pass cut-offs can

31、be switched independently for fine control over filter operation. TX equalizer (SSB/AM/FM for each mode) The equalizer enables the adjustment of frequency characteristics to suit the voice quality and microphone characteristics on the transmitting end. Users can choose from flat (default), high boos

32、t (2 types), Formant pass, and bass boost (2 types), as well as conventional and user settings (using the ARCP-590G). Antenna output function (shared with DRV connector) Switching the drive output (DRV) connector to the external receiver antenna output function in the menu settings enables output of

33、 the signal allocated by the antenna. Built-in high-speed automatic antenna tuner The built-in preset-type automatic antenna tuner covers amateur bands in the 1606m band range and can operate when the transceiver is receiving. High- speed operation and the proven relay method enable rapid QSY throug

34、h instantaneous band changing. Note: Proper decoding may not be available due to reception conditions, etc. Note: When you use the Antenna output function, due to losses in the splitter, the receive sensitivity and gain decrease by approximately 3 dB. During transmission, the Drive output will leak

35、a little through internal isolation (-20dBm or less). The ON/OFF status of the Antenna output function is stored separately in the 50MHz band and HF band. External connector terminals Amber Green 10-step selection possible from amber to green TX monitor The transmission monitor function outputs tran

36、smission audio via the speaker in 20 steps, allowing you to check sound quality. Other TX features VOX function (adjustable gain, selectable delay time) Adjustable TX power output Adjustable MIC gain Adjustable CAR level 7 Remote control of the TS-590SG via computer Using the ARCP-590G (radio contro

37、l program), virtually all functions can be controlled via a computer. Changing various function settings and managing memory channels can all be done from your PC. The ARCP- 590G also enables the recording and erasure of voice messages. New Split function enabling quick setting Direct frequency entr

38、y, Direct band selection In addition to conventional split frequency setting methods, the TS-990s proven split setting functionality has been included. A long press of the SPLIT key, when making a 2kHz up setting, will enable quick setting by pressing 2 on the keypad. Furthermore, TH-D72A/ TM-D710A/

39、D710GA 440 MHz /144 MHz TH-D72A/ TM-D710A/D710GA 440 MHz/144 MHz HF Transceiver TS-590SG 440 MHz band Confi rmation of HF frequency 144 MHz band HF receive audio 440 MHz band Voice signals, Control signals COM connector MIC HF antenna Transporter Commander 3.5 mm EXT SP *KENWOOD SKY COMMAND SYSTEM I

40、I uses a pair of TH-D72A/TM-D710A/TM-D710GA transceivers. Note: Refer to applicable amateur radio regulations to check whether you are permitted to use this function. Enables full-duplex operation with improved functionality such as visual confirmation of HF frequency on the LCD panel. Control via T

41、NC (AX.25) enables more access to HF functions: XIT, mode switching, split-frequency operations on/off, memory shift, and frequency step selection. The transporter sends out its pre-programmed call sign via CW every 10 minutes. KENWOOD SKY COMMAND SYSTEM II Super Ease of Operation, More Enjoyable TX

42、/RX Performance and User-friendly Machine Interface. A variety of functions for easy operation User-friendly menus for outstanding operating ease The TS-590SG features 100 menu functions and intuitive operation with its combination of menu and arrow keys. The menu mode is shown in the 7-segment disp

43、lay unit, while relevant guidance information is scroll-displayed in the 13-segment display unit, making a variety of detailed operations possible. Voice guide, recording function (option) The VGS-1 voice guide and storage unit enables voice guidance for frequency, key operation, settings, etc., and

44、 recording/ playback of messages. A Manual Mode, in which vocalization takes place only when buttons are pressed, has been added to the voice guidance. Either English or Japanese can be selected for the voice guidance language. Memory/Scan functions Easy-to-use, diverse memory functions The transcei

45、ver features a memory that can store up to 120*1 frequency memory channels, with each able to be given a memory name of up to 8 letters. Also included are the memory scroll function, which can be used to check memory data without changing operating frequency, memory channel copy, which enables the c

46、opying of memory data to another channel, single channel memory clear, memory lockout, memory shift, and the ability to change memory data/frequency temporarily. Other features include the Quick Memory function, which can store up to 10 channels*2 on the fly, and the capacity for temporary changes t

47、o memory shift and memory data. Multiple scan functions Program scan, memory scan, group scan, subtone scan and CTCSS scan are included among the many scan functions available. The transceiver also offers program slow scan, which automatically reduces the scanning speed around any frequency of speci

48、al interest. PC control through USB connectivity PC control of the transceiver and transceiver audio transmission have been made possible through a USB cable with the inclusion of a dedicated PC-control USB connection terminal. Easily discernible beep sound Different beeps sound in response to funct

49、ion circumstances, enabling intuitive comprehension of transceiver status. Programmable functions (PF A, PF B and MULTI/CH SW) Frequently used and other functions can be assigned to the programmable function (PF) keys. With the TS-590SG, in addition to the PF keys, functions can also be assigned to the MULTI/CH knobs Push SW. Quick settings are made possible by assigning level setting functions such as keying speed. The RIT/XIT/CL keys can also be used as programmable function keys. RX ATT, pre-amp RF gain adjust AF gain SQL level set FSK Basic R