AS-1729_antenna_serv_TM11-5985-262-24P_1985.pdf

《AS-1729_antenna_serv_TM11-5985-262-24P_1985.pdf》由会员分享，可在线阅读，更多相关《AS-1729_antenna_serv_TM11-5985-262-24P_1985.pdf（34页珍藏版）》请在收音机爱好者资料库上搜索。

1、TM 11-5985-262-24P TECHNICAL MANUAL ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOL LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS special tools; special test, measurement, and diagnostic equipment (TMDE); and other special support equipment required for

2、performance of organizational, direct support, and general support maintenance of the AS-1729/VRC. It authorizes the re- quisitioning, issue, and disposition of spares, repair parts and special tools as indicated by the source, maintenance and recoverability (SMR) codes. 2. General This Repair Parts

3、 and Special Tools List is divided into the following sections: a. Section II. Repair Parts List. A Iist of spares and repair parts authorized by this RPSTL for use in the performance of maintenance. The list also includes parts which must be removed for replacement of the authorized parts. Parts li

4、sts are composed of functional groups in ascending numeric sequence, with the parts in each group listed in ascending item number sequence. Figure numbers are listed directly beneath the group header. b. Section III. Special Tools List. Not applicable. c. Section IV. National Stock Number and Part N

5、umber lndex. A list, in National item identification number (NIIN) sequence, of all National stock numbered items appearing in the listing, followed by a list in alphameric sequence of all part numbers appearing in the listings. National stock numbers and part numbers are cross-referenced to each il

6、lustration figure and item number appearance. 3. Explanation of Columns (Section II and III) a. Item No. (Column (1). Indicates the number used to identify items called out in the illustration. b. SMR Code (Column (2). The source, maintenance, and recoverability (SMR) code is a five-position code co

7、ntaining supply/requisitioning information, maintenance category authorization criteria, and disposition instruction, as shown in the following breakout: SourceMaintenance CodeCode xx 1st two xx positions 3d position 4th position How you get an item. Who can install, Who can do com- replace or use t

8、he plete repair (see item. note) on the item. Recoverability Code x Who determines disposition action on anu n se r- viceable item. 1 *TM 11-5985-262-24P NOTE Complete repair: Maintenance capacity, capability, and authority to per- form all corrective maintenance tasks of the “Repair” function in a

9、use/user environment in order to restore serviceability to a failed item. (1) Source code. The source code tells you how to get an item needed for maintenance, repair, or overhaul of an end item/equipment. Explanations of source codes follows: Code PA PB PC PD PE PF PG KD KF KB MOMade at org/AVUM ca

10、tegory MFMade at DS/AVUM category M H M a d e a t G S category MLMade at Specializ- ed Repair Activity (SRA) MDMade at Depot AOAssembledby o r g / A V U M category AFAssembledby DS/AVIM category AHAssembled by GS category ALAssembled by SRA ADAssembledby Depot Explanation Stocked items; use the appl

11、icable NSN to request/requisition items with these source codes. They are authorized to the category in- dicted by the code entered in the third position of the SMR code. NOTE Items coded PC are subject to deterioration. Items with these codes are not to be requested/requisitioned in- dividually. Th

12、ey are part of a kit which is authorized to the maintenance category indicated in the third position of the SMR code. The complete kit must be requisitioned and applied. Items with these codes are not to be requested/requisitioned in- dividually. They must be made from bulk material which is iden- t

13、ified by the part number in the description and usable on code (UOC) column and listed in the Bulk Material group of the repair parts list. If the item is authorized to you by the third position code of the SMR code, but the source code indicates it is made at a higher category, order the item from

14、the higher category of maintenance. Items with these codes are not to be requested/requisitioned in- dividually. The parts that make up the assembled item must be re- quisitioned or fabricated and assembled at the category of maintenance indicated by the source code. If the disposition code of the S

15、MR code authorizes you to replace the item, but the source code indicates the item is assembled at a higher category, order the item from the higher category of maintenance. XADo not requisition an “XA” coded item. Order its next higher assembly. XBlf an “XB” item is not available from salvage, orde

16、r it using the FSCM and part number given. XCinstallation drawing, diagram, instruction sheet, field service drawing, that is identified by manufac- turers part number. XDitem is not stocked. Order an “XD” coded item through normal supply channels using the FSCM and part number given, if no NSN is a

17、vailable. NOTE Cannibalization or controlled exchange, when authorized, may be used as a source of supply for items with the above source codes, except for those source coded XA or those aircraft support items restricted by requirements of AR 750-1. 2 *TM 11-5985-262-24P (2) Maintenance code. Mainte

18、nance codes tell you the category of maintenance authorized to USE and REPAIR support items. The maintenance codes are entered in the third and fourth positions of the SMR code as follows: (a) The maintenance code entered in the third position tells you the lowest maintenance category authorized to

19、remove, replace, and use an item. The maintenance code entered in the third position will indicate authorization to one of the following categories of maintenance. CodeApplicationlExplanation CCrew or operator maintenance done within organizational or aviation maintenance. OOrganizational or aviatio

20、n unit category can remove, replace, and use the item. FDirect support or aviation intermediate category can remove, replace, and use the item. HGeneral support category can remove, replace, and use the item. LSpecialized repair activity can remove, replace, and use the item. DDepot category can rem

21、ove, replace, and use the item. (b) The maintenance code entered in the fourth position tells whether or not the item is to be repaired and identifies the lowest maintenance category with the capability to do complete repair (i.e., perform all authorized repair functions). This position will contain

22、 one of the following maintenance codes. NOTE Some limited repair may be done on the item at a lower category of maintenance, if authorized by the Maintenance Allocation Chart (MAC) and SMR codes. CodeApplicationlExplanation OOrganizational or aviation unit is the lowest category that can do complet

23、e repair of the item. FDirect support or aviation intermediate is the lowest category that can do complete repair of the item. H-General support is the lowest category that can do complete repair of the item. LSpecialized repair activity (designate the specialized repair activity) is the lowest cate

24、gory that can do complete repair of the item. DDepot is the lowest category that can do complete repair of the item. ZNonreparable. No repair is authorized. BNo repair is authorized. (No parts or special tools are authorized for the maintenance of a “B” coded item.) However, the item may be recondit

25、ioned by adjusting, lubricating, etc., at the user category. (3) Recoverability code. Recoverability codes are assigned to items to indicate the disposition action on unserviceable items. The recoverability code is entered in the fifth position of the SMR Code as follows: Recoverability codesApplica

26、tionlExplanation ZNonreparable Item. When unserviceable, condemn and dispose of the item at the category of maintenance shown in the third position of SMR Code. OReparable Item. When uneconomically reparable, condemn and dispose of the item at organizational or aviation unit category. FReparable Ite

27、m. When uneconomically reparable, condemn and dispose of the item at direct support or aviation intermediate category. HReparable Item. When uneconomically reparable, condemn and dispose of the item at general sup- port category. DReparable item. When beyond lower category repair capability, return

28、to depot. Condemnation and disposal of item not authorized below depot category. LReparable item. Condemnation and disposal not authorized below specialized repair activity (SRA). AItem requires special handling or condemnation procedures because of specific reasons (e.g., precious metal content, hi

29、gh dollar value, critical material, or hazardous material). Refer to ap- propriate manuals/directives for specific instructions. 3 c. FSCM (Column (3). The Federal Supply Code for Manufacturer (FSCM) is a 5-digit numeric code which is used to identify the manufacturer, distributor, or Government age

30、ncy, etc., that supplies the item. d. Part Number (Column (4). Indicates the primary number used by the manufacturer (individual, com- pany, firm, corporation, or Government activity), which controls the design and characteristics of the item by means of its engineering drawings, specifications, sta

31、ndards, and inspection requirements to identify an item or range of items. When you use a NSN to requisition an item, the item you receive may have a different part number from the part ordered. e. Description and Usable on Code (UOC) (Column (5). This column includes the following information. (1)

32、The Federal item name and, when required, a minimum description to identify the item. (2) The statement “END OF FIGURE” appears just below the last item description in Column (5) for a given figure in both section II and section Ill. f. Qty. (Column (6). Indicates the quantity of the item used in th

33、e breakout shown on the illustration figure, which is prepared for a functional group, subfunctional group, or an assembly. A “V” appearing in this column in lieu of a quantity indicates that the quantity is variable and the quantity may vary from ap- plication to application. 4. Explanation of Colu

34、mns (Section IV) a. National Stock Number (NSN) Index. (I) Stock number column. This column lists the NSN by National item identification number (NIIN) se- quence. The NIIN consists of the last nine digits of the NSN. When using this column to locate an item, ignore the first four digits of the NSN.

35、 When requisitioning items use the complete NSN (13 digits). (2) Fig. column, This column lists the number of the figure where the item is identified/located. The il- lustrations are in numerical sequence in sections II and Ill. (3) Item column, The item number identifies the item associated with th

36、e figure listed in the adjacent Fig. column. This item is also identified by the NSN listed on the same line. b. Part Number Index. Part numbers in this index are listed by part number in ascending alphameric se- quence. (1) FSCM column. This column lists the Federal supply code for manufacturer (FS

37、CM). (2) Part number column. This column indicates the part number assigned to the item. (3) Stock number column. This column lists the National stock number for the associated part number and manufacturer identified in the part number and FSCM columns to the left. (4) Fig. column. This column lists

38、 the number of the figure where the item is identified/located in sec- tions II and Ill, (5) Item column. The item number is that number assigned to the item as it appears in the figure referenced in the adjacent figure number column. 5. Special Information a. Associated Publications. The publicatio

39、n listed below pertains to the AS-1729/VRC and its com- ponents: TM 11-5985-262-14, Antenna AS-1729/VRC b. Nationa/ Stock Numbers. National stock numbers (NSNS) that are missing from P source coded items have been applied for and will be added to this TM by future change/revision when they are enter

40、ed in the Army Master Data File (A MD F). Until the NSNS are established and published, submit exception re- quisitions to: Commander, US Army Communications-Electronics Command and Fort Monmouth, ATTN: AMSEL-MM. Fort Monmouth, NJ 07703-5006 for the part required to support your equipment. 6. How to

41、 Locate Repair Parts a. When National stock number or part number is not known. (1) First. Using the table of contents, determine the assembly group or subassembly group to which the item belongs. This is necessary since figures are prepared for assembly groups and subassembly groups, and listings a

42、re divided into the same groups. (2) Second. Find the figure covering the assembly group or subassembly group to which the item belongs. 4 *TM 11-5985-262-24P NOTE *TM 11-5985-262-24P (3) Third. Identify the item on the figure and note the item number. (4) Fourth. Refer to the Repair Parts List for

43、the figure to find the part number for the item number noted on the figure. (5) Fifth. Refer to the Part Number Index to find the NSN, if assigned. b. When National stock number or part number is known. (1) First. Using the index of National stock numbers and part numbers, find the pertinent Nationa

44、l stock number or part number. The NSN index is in National item identification number (NIIN) sequence para 4a(1). The part numbers in the part number index are listed in ascending alphameric sequence (para 4b). Both indexes cross-reference you to the illustration figure and item number of the item

45、you are look- ing for. (2) Second. After finding the figure and item number, verify that the item is the one youre looking for, then locate the item number in the repair parts list for the figure. 7. Abbreviations Not applicable. (Next printed page is 10) 5 TM 11-5985-262-24P FIGURE 1. ANTENNA AS-17

46、29/VRC. 10 TM11-5985-262-24P SECTION II (1)(2)(3)(4)(5)(6) ITEMSMRPART NO.CODEFSCMNUMBERDESCRIPTION AND USABLE ON CODE (UOC)QTY GROUP OO ANTENNA AS-1729/VRC FIGURE 1 1XAOHH80058MX-6707/VRCMATCHING UNIT BASE1 2PAOZZ96906MS9068-211PACKING,PREFORMED1 3PAOZZ80063SC-C-877429COVER,REINFORCING1 4PAOZZ96906

47、MS51959-30SCREW,MACHINE2 5PAOOO80058AS-1730/VRCANTENNA ELEMENT1 6PAOZZ80063SC-C-208747ANTENNA TIEDOWN KIT1 7PAOZZ80063SC-C-446180ANTENNA TIP ASSEMBL1 8PAOZZ80058AT-1095/VRCANTENNA ELEMENT END OF FIGURE 11 TM 11-5985-262-24P FIGURE 2. MATCHING UNIT BASE, ANTENNA MX-6707/VRC (SHEET 1 OF 2). 13 TM 11-5

48、985-262-24P FIGURE 2. MATCHING UNIT BASE, ANTENNA MX-6707/VRC (SHEET 2 OF 2). 14 TM11-5985-262-24P SECTION II (1)(2)(3)(4)(5)(6) ITEMSMRPART NO.CODEFSCMNUMBERDESCRIPTION AND USABLE ON CODE (UOC)QTY GROUP 01 MATCHING UNIT BASE, ANTENNAMX-6707/VRC FIGURE 2 1PAHZZ96906MS35308-302SCREW,CAP,HEXAGON6 2PAH

49、ZZ80063SM-D-542042BASE,ANTENNA SUPPOR1 3PAHZZ96906MS51966-51SETSCREW2 4PAHZZ96906MS9068-015PACKING,PREFORMED1 5PAOZZ80063SC-B-911110-2COVER,ANTENNA BASE1 6PAOZZ96906MS16996-11BSCREW,CAP,SOCKET HE1 7PAHZZ96906MS9068-220PACKING PREFORMED1 8PAHZZ80063SC-D-877432GASKET1 9PAHZZ80063SM-D-542084RELAY SWITCH ASSY1 10PAHZZ96906MS35649-224NUT,PLAIN,HEXAGON6 11PAHZZ02289J2K-4730-1281RELAY,ELECTROMAGNET1 12PAHZZ96906MS51957-3SCREW,MACHINE6 13PAHZZ80063SM-D-542103WIRING HARNESS,BRAN1 14PAHZZ80063SM-C-542061CABLE ASSEMBLY,RADI1 15PAHZZ96906MS29513-006PACKING,PREFORMED1 16PAHZZ8006