AN-PRC-104B_repair_parts_TM11-5820-1046-20P_1990.pdf

《AN-PRC-104B_repair_parts_TM11-5820-1046-20P_1990.pdf》由会员分享，可在线阅读，更多相关《AN-PRC-104B_repair_parts_TM11-5820-1046-20P_1990.pdf（36页珍藏版）》请在收音机爱好者资料库上搜索。

1、T M 1 1 - 5 8 2 0 - 1 0 4 6 - 2 0 P T E C H N I C A L M A N U A L UNIT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST F O R RADIO SET AN/PRC-104B (V)4 (NSN 5820-01-262-9550) Distribution authorized to the Department of Defense and DOD contractors only for official use or for administration or opera

2、tional purposes. This Determination was made on 1 July 1989. Other requests for this document will be referred to Commander, US Army Communications-Electronics Command and Fort Monmouth, ATTN: AMSEL-LC-ME-P, Fort Monmouth, NJ 07703-5000. DESTRUCTION NOTICE- Destroy by any method that will prevent di

3、sclosure of contents or reconstruction of the document. H E A D Q U A R T E R S , D E P A R T M E N T O F T H E A R M Y 1 FEBRUARY 1990 Technical ManualHEADQUARTERS DEPARTMENT OF THE ARMY No.Washington, DC, UNIT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST FOR RADIO SET AN/PRC-14B(V)4 Current as

4、of 1 November 1989 REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this manual.If you find any mistakes or if you know of a way to improve the procedures, please let us know.Mail your letter, DA Form (Recommended Changes to Publications and Blank Forms) , or DA Form 228-2 located

5、 in back of this manual direct to: Commander, US Army Communications- Electronics Command and Fort Monmouth, ATTN:AMSEL-LC-ME-PS , Fort Monmouth, New Jersey .In either case, a reply will be furnished direct to you. Section Group Section Table of Contents I. II. 1 2 3 4 5 6 7 III. IV. Introduction. .

6、 . . . . . . . . . . . . . . . Repair Parts List . . . . . . . . . . . AN/PRC- (V)4 Radio Set. . . . . . . Receiver Transmitter. . . . . . . . . . Amplifier Radio Frequency. . . . . . . Transit Case (No parts authorized) Antenna (No parts authorized) Antenna Group (No parts authorized) Storage Batte

7、ry (No parts authorized) Battery Case (No parts authorized) Special Tools List (Not applicable) Cross-Reference Indexes National Stock Number Index . . . . Part Number Index. . . . . . . . . Figure and Item Number Index. . . . Illus/ PageFigure 1 1-1 1-l1 2-12 3-13 I-1 I-2 I-3 i/(ii blank) TM 11-582

8、0-1046-20P SECTION 1 INTRODUCTION 1. Scope Thismanuallistsandauthorizesspares and repair parts; special tools;specialtest,measurement,and diagnostic equipment (TMDE); andotherspecial support equipment required for performance of unit maintenanceof the AN/PRC- (V)4.It authorizes the requisitioning, i

9、ssueanddispositionof spares,repair parts and special tools as indicated by the source, maintenance and recoverability (SMR) codes. 2. General ThisRepairPartsandSpecialToolsList isdividedintothe following sections: a.Section II.RepairParts List.A list of spares and repair parts authorized bythisRPSTL

10、foruse intheperformance of maintenance.The list also includes parts which must be removed for replacement oftheauthorizedparts.Parts lists are composed of functionalgroups inascendingnumeric sequence, with the parts in eachgrouplisted in ascending item number sequence.Figure numbers are listed direc

11、tly beneath the group header. b.Section III.Special Tools List.Not applicable. c.Section IV.Cross-ReferenceIndexes.A list,in National item identificationnumber(NIIN)sequence,of all National stock numbereditemsappearing inthelisting,followedbya list in alphamericsequence ofallpart numbers appearing i

12、n the listings. Nationalstocknumbers and part numbers are cross-referenced to each illustrationfigureanditemnumber appearance.The figure number anditemnumberindexlistsfigureanditemnumbers in numeric sequenceandcross-referencesNational stock number, Federal Supply Code for Manufacturer and part numbe

13、rs. 3. Explanation of Columns (Section II and III) a.Item No.(Column (1).Indicates the number used to identify items called out in the illustration. 1 TM 11-5820-1046-20P b.SMRCode(Column (2). Thesource,maintenance,and recoverability(SMR)codeis afive-positioncodecontaining supply/requisitioninginfor

14、mation,maintenance category authorization criteria,anddispositioninstruction,asshownin the following breakout: NOTE Complete repair:Maintenance capacity, capability,and authority to perform all corrective maintenance tasks of the“repair” function in a use/user environment in order to restore service

15、ability to a failed item. (1)Sourcecode.The source code tells you how to get an item neededfor maintenance, repair,or overhaul of an end item/equipment. Explanations of source codes follows: CodeExplanation Stocked items:use the applicable NSN to request/requisition items with these source codes.The

16、y are authorized to the category indicated by the code entered in the third position of the SMR code. NOTE Items coded PC are subject to deterioration. Items with these codes are not to be requested/requisitioned individually. They are part of a kit which is authorized to the maintenance category in

17、dicated in the third position of the SMR code.The complete kit must be requestioned and applied. 2 TM 11-5820-1046-20P CodeExplanation Code Items with these codes are not to be requested/requisitioned individually. They must be made from bulk material which is identified by the part number in the de

18、scription and usable on code (UOC) column and listed in the Bulk Material group of the repair parts list. If the item is authorized to you by the third position code of the SMR code, but the source code indicates it is made at a higher category, order. the item from the higher category of maintenanc

19、e. Items with these codes are not to be requested/requisitioned individually. The parts that make up the assembled item must be requisitioned or fabricated and assembled at the category of maintenance indicated by the source code.If the third position code of the SMR code authorizes you to replace t

20、he item, but the source code indicates the item is assembled at a higher category,order the item from the higher category of maintenance. Explanation XA -Do not requisition an “XA coded item.Order its next higher assembly. XB -If an“XB” item is not available from salvage, order it using the FCSM and

21、 part number given. XC -Installation drawing, diagram, instruction sheet, field service drawing,that is identified by manufacturers part number. XD- Item is not stocked.Order an “XD” coded item through normal supply channels using the FSCM and part number given, if no NSN is available. NOTE Cannibal

22、ization or controlled exchange, when authorized, may be used as a source of supply for items with the above source codes, except for those source coded “XA” or those aircraft support items restricted by requirements of AR . 3 TM 11-5820-1046-20P (2)Maintenancecode.Maintenance codes tell you the cate

23、gory ofmaintenanceauthorized toUSEandREPAIRsupport items.The maintenancecodesareenteredin the third and fourth positions of the SMR code as follows: (a)Themaintenancecodeentered inthethird position tellsyouthelowestmaintenancecategoryauthorizedto remove, replace,anduse an item.The maintenance code e

24、ntered in the third positionwillindicateauthorization tooneofthefollowing categories of maintenance. CodeApplication/Explanation C -Crew or operator maintenance done within organizational or aviation maintenance. O -organizational or aviation unit category can remove, replace, and use the item. F -D

25、irect support or aviation intermediate category can remove, replace,and use the item. H -General support category can remove, replace, and use the item. L -Specialized repair activity can remove, replace, and use the item. D -Depot category can remove, replace, and use the item. (b)Themaintenancecod

26、eentered inthe fourth position tellswhether ornotthe item is to be repaired and identifies the lowestmaintenance category with the capability to do complete repair (i.e.,performall authorized repair functions) . This position will contain one of the following maintenance codes. NOTE Some limited rep

27、air may be done on the item at a lower category of maintenance, if authorized by the Maintenance Allocation Chart (MAC) and SMR codes. CodeApplication/Explanation O -Organizational or aviation unit is the lowest category that can do complete repair of the item. F -Direct support or aviationintermedi

28、ate is the lowest category that can do complete repair of the item. H -General support is the lowest category that can do complete repair of the item. L Specialized repair activity (designate the specialized repair activity) is the lowest category that can do complete repair of the item. D -Depot is

29、 the lowest category that can do complete repair of the item. 4 TM 11-5820-1046-20P CodeApplication/Explanation Z -Nonreparable.No repair is authorized. B -NO repair is authorized.(No parts or special tools are authorized for the maintenance of a“B” coded item.) However, the item may be reconditione

30、d by adjusting, lubricating, etc., at the user category. (3)Recoverabilitycode.Recoverability codes are assigned to itemsto indicate the disposition action on unserviceable items.The recoverabilitycodeis entered in the fifth position of the SMR Code as follows: Recoverability codesApplication/Explan

31、ation Z -Nonreparable item.When unserviceable,condemn and dispose of the item at the category of maintenance shown in the third position of SMR code. O -Reparable item.When uneconomically reparable, condemn and dispose of the item at organizational or aviation unit category. F -Reparable item.When u

32、neconomically reparable, condemn and dispose of the item at direct support or aviation intermediate category. H -Reparable item.When uneconomically reparable, condemn and dispose of the item at general support category. D -Reparable item.When beyond lower category repair capability, return to depot.

33、Condemnation and disposal of item not authorized below depot category. L -Reparable item.Condemnation and disposal not authorized below specialized repair activity (SRA). A -Item requires special handling or condemnation procedures because of specific reasons (e.g., precious metal content, high doll

34、ar value,critical material, or hazardous material).Refer appropriate manuals/directives for specific instructions. c.FSCM(Column(3).The Federal Supply Code for Manufacturer (FSCM is a 5-digitnumericcodewhich isused to identify the manufacturer,distributor,or Government agency, etc., that supplies th

35、e item. d.PartNumber(Column (4).Indicates the primary number used bythe manufacturer(individual, company,firm,corporation, or Governmentactivity),whichcontrols the design and characteristics oftheitembymeansof its engineering drawings, specifications, standards,andinspectionrequirements to identify

36、an item or range of items. 5 TM 11-5820-1046-20P NOTE When you use an NSN to requisition an item,the item youreceive may have a different part number from the part ordered. e.DescriptionandUsable onCode(UOC)(Column (5).This column includes the following information. (1)TheFederalitemnameand ,whenreq

37、uired, aminimum description to identify the item. (2)Thestatement“ ENDOF FIGURE” appears just below the last itemdescriptionin Column (5) for a given figure in both section II and section III. f. Qty(Column (6).Indicates the quantity of the item used in thebreakoutshown on the illustration figure, w

38、hich is prepared for afunctionalgroup,subfunctionalgroup, or anassembly. A “V” appearing inthiscolumn inlieu of a quantity indicates that the quantity isvariableandthe quantity may vary from application to application. 4. Explanation of Columns (Section IV) a. National Stock Number (NSN) Index. (1)S

39、tocknumber column.This column lists the NSN by National itemidentification number (NIIN) sequence.The NIIN consists of the lastninedigits oftheNSN.When using this column to locate an item,ignorethefirst four digits of the NSN.When requisitioning items use the complete NSN (13 digits). (2) Fig.column

40、.Thiscolumn lists the number of thefigure wheretheitem isidentified/located.Theillustrations arein numerical sequence in sections II and III. (3)Item column .Theitemnumberidentifies the item associatedwiththefigure listed in the adjacent Fig. column. This item is also identified by the NSN listed on

41、 the same line. b.PartNumberIndex.Part numbers in this index are listed by partnumber in ascending alphameric sequence. (1)FSCMcolumn .This column lists the Federal supply code for manufacturer. (2)Partnumbercolumn .This column indicates the part number assigned to the item. 6 TM 11-5820-1046-40P TM

42、 11-5820-467-24P TM 11-5820-477-23P TM 11-582-1045-12 TM 11-5820-1046-12 TM 11-5820-1047-12 TM 11-5820-1045-20P TM 11-5820-1047-20P TM 11-5985-379-14 therefore,there may be a break in the 7 TM 11-5820-1046-20P itemnumbersequence,figurenumberandpagenumber .Only illustrationscontainingorganizationalor

43、 aviation unit authorized items appear in this RPSTL. b.NationalStockNumbers.National stock numbers (NSNS) that aremissingfrom P source coded items have been applied for and will beadded tothis TM by future change/revision when they are entered inthe Army Master Data File (AMDF).Until the NSNS are e

44、stablished andpublished,submit exception requisitions to:Commander, US Army Communications-ElectronicsCommandandFortMonmouth,ATTN : AMSEL-LC-MM,FortMonmouth, NJfor the part required to support your equipment. 6. How to Locate Repair Parts a.When National stock number or part number is not known. (1)

45、First.Using the table of contents,determine the assembly group orsubassemblygroup towhichtheitembelongs.This is necessarysincefiguresarepreparedforassemblygroupsand subassembly groups,and listings are divided into the same groups. (2)Second .Findthefigurecovering the assembly group or subassembly gr

46、oup to which the item belongs. (3) Third.Identifythe item on the figure and note the item number . (4)Fourth.Referto the Repair Parts List for the figure to find the part numberfor the item number noted on the figure. (5)Fifth.Refer to the Part Number Index to find the NSN, if assigned. b.When Natio

47、nal stock number or part number is known. (1)First.Using the index of National stock numbers and part numbers,findthepertinent National stock number or part number. TheNSNindex isinNationalitem identification sequence(para 4a(1). number (NIIN) The part numbers in the part number index are listed ina

48、scendingalphamericsequence(para 4b).Both indexes cross-referenceyou to the illustration figure and item number of the item you are looking for. (2)Second.Afterfinding the figure and item number, verify thattheitem istheone youre looking for, then locate the item number in the repair parts list for t

49、he figure. 7. Abbreviations Not applicable. 8 Section IITM 11-5820-1046-20P Figure 1.AN/PRC-104B(V)4 Radio Set SECTION IITM11-5820-1046-20P (1)(2)(3)(4)(5) ITEMSMR (6) PART NOCODE FSCMNUMBERDESCRIPTION AND USABLE ON CODES(UOC) QTY G R O U P 0 0 AN/PRC-104B(V)4 RADIQ SET FIGURE 1 1 XBOZZ 81337 2-3-291 2 XBOZZ 81337 2-2-344 3 PAOZZ 80058 AT-271A/PRC 4 PAOZZ 80058 AB-129/PR 5 PAOZZ 01365 79A5029AOQ50 6 PAOZZ 80058 H250A/U 7 XBOZZ 05276 2249-C-22 8 PAODD 80058 AM-6874IPRC-104 9 PAOHH 80058 RT-1209A/URC 10 PAOBA 80058 BB-590/U 11 PCOZA 80058 BA-5590/U 12 PAOZZ 87990 79