AN-UGC-74A_terminal_communications_serv_TM11-5815-602-24P_1990.pdf

《AN-UGC-74A_terminal_communications_serv_TM11-5815-602-24P_1990.pdf》由会员分享，可在线阅读，更多相关《AN-UGC-74A_terminal_communications_serv_TM11-5815-602-24P_1990.pdf（316页珍藏版）》请在收音机爱好者资料库上搜索。

1、ARMYTM 11-5815-602-24P NAVY EE161-DM-PLL-010/UGC-74 AIR FORCETO 31W4-2UGC74-4 MARINE CORPSTM 08008C-24P/4A ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS) FOR TERMINALS, COMMUNICATIONS AN/

2、UGC-74A(V)3 (NSN 5815-01-062-8194) , AN/UGC-74B(V)3 (NSN 5815-01-214-6237) AN/UGC-74C(V)3 (NSN 5815-01-211-4122) Distribution authorized to the Department of Defense end DOD contractors only for official use or for administrative or operational purposes. This determination was made on 3 May 1990.Oth

3、er requests for the document will be referred to Commander, US Army Communications-Electronics Command and Fort Monmouth, ATTN: AMSEL-LC-ME-P, Fort Monmouth, NJ 07703-5000. DESTRUCTION NOTICE - Destroy by any method that will prevent disclosure of contents or reconstruction of the document. DEPARTME

4、NTS OF THE ARMY, THE NAVY, AND THE AIR FORCE AND HEADQUARTERS, MARINE CORPS 15 AUGUST 1990 *TM 11-5815-602-24P EE161-DM-PLL-010/UGC-74 TO 31W4-2UGC74-4 TM 08008C-24P/4A Technical ManualDEPARTMENTS OF THE ARMY, No. 11-5815-602-24PTHE NAVY, AND THE AIR FORCE Technical ManualAND HEADQUARTERS MARINE COR

5、PS No. EE161-DM-PLL-010/UGC-74 Technical Order No. 31W4-2UGC74-4 Technical Manual No. 08008C-24P/4AWashington, DC, 15 August 1990 ORGANIZATIONAL, DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS LIST (INCLUDING DEPOT MAINTENANCE REPAIR PARTS AND SPECIAL TOOLS) FOR TERMIN

6、ALS, COMMUNICATIONS AN/UGC-74A(V)3 (NSN 5815-01-062-8194) AN/UGC-74B(V)3 (NSN 5815-01-214-6237) AN/UGC-74C(V)3 (NSN 5815-01-211-4122) Current as of 15 May 1990 REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this manual. If you find any mistakes or if you know of a way to improve

7、 the procedures, please let us know. Mail your letter, DA Form 2028 (Recommended Changes to Publications and Blank Forms),or DA Form 2028-2 located in the back of this manual direct to:Commander, US Army Communications-Electronics Command and Fort Monmouth, ATTN:AMSEL-LC-ME-PS, Fort Monmouth, NJ 077

8、03-5000. For Air Force, submit AFTO Form 22 (Technical Order System Publica- tion Improvement Report and Reply) in accordance with paragraph 6-5, Section VI, TO 00-5-1.Forward direct to prime ALC/MST. For Navy, mail comments to the Commander, Space and Naval Warfare Command, ATTN: SPAWAR 8122, Washi

9、ngton DC, 20363-5100. For Marine Corps, submit NACMC10772 (Recommended Change to Technical Publications) to CommandingGeneral, Marine Corps Logistic Base (Code 850), Albany, Georgia 31704. In either case a reply will be furnished direct to you. Section *This manual Table of Contents Illus Page Figur

10、e Introduction. . . . . . . . . . . . . . . . . . I Repair Parts List. . . . . . . . . . . . . . . . . . . . . . . . . 1-1 supersedes TM 11-5815-602-24P, 15 February 1988 i I. II. TM 11-5815-602-24P TABLE OF CONTENTS - Continued Illus Page Figure Group00 AN/UGC-74A(V)3, AN/UGC-74B(B)3 and AN/UGC-74C

11、(V)3. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 01 Teleprinter Assembly (3A1) . . . . . . . . . . . . . . . . .2-1 0101 Circuit Card Assembly, CPU (3A1A) (See TM 11-5815-612-40special tools; special test, measurement, and diagnostic equipment (TMDE); and other special support equipme

12、nt required for performance of organizational, direct support, and generalsupport maintenance of the AN/UGC-74A(V)3, AN/UGC-74B(V)3, and AN/UGC-74C(V)3.It authorizes the requisitioning, issue and disposition of spares, repair parts and special tools as indicated by source, maintenance, and recoverab

13、ility (SMR) codes. 2. General. This RepairParts and SpecialTools List is divided into the following sections: a.Section II.Repair Parts List.A list of spare and repair parts authorized by this RPSTL for use in the performance of maintenance.The list also includes parts which must be removed for repl

14、acement of the authorized parts.Parts lists are composed of functional groups in ascending numeric sequence, with the partsin each group listed in ascending item number sequence.Figure numbers are listed directly beneath the group header.Bulk materials are listed in item name sequence.Repair part ki

15、ts are listed separately in their own functional group within section II. Repair parts for reparable specialtools are also listed in this section. Items listed are shown on the associated illustrations. b.Section III- Special Tools List.A list of special tools, special TMDE,and other specialsupport

16、equipment authorized by this RPSTL (as indicated by Basisof Issue (BOI) information in(column (5) for the performance of maintenance. c.Section IV.Cross-Reference Indexes. A list, in National item identification number(NIIN) sequence, of all National stock numbered items appearing in the listing, fo

17、llowed by a list in alphanumeric sequence of all part numbers appearing in the listings.National stock numbers and part numbers are cross-referenced to each illustration figure and item number appearance.The figure numberand item number index lists figure and item numbers innumeric sequence and cros

18、s-references National stock numbers, Commercial and Government Entity Code and part numbers. 3. Explanation of Columns (Section II and III) a.Item No.(Column (1).Indicates the number used to identify items called out in the illustration. 1 TM 11-5815-602-24P b.SMR Code (Column (2).The source, mainte

19、nance, and recoverability (SMR) code is a five-position code containing supply/requisitioning information,maintenance category authorization criteria, and disposition instruction, as shown in the following breakout: SourceMaintenanceRecoverability CodeCode How you get an item3rd position4th position

20、Who determines disposition action on an unserviceable Who can install.Who can doitem replace or usecomplete the itemrepair (see note) on the item. NOTE Completerepair:Maintenancecapacity, capability,and authority to perform all corrective maintenance tasks of the “repair” function in a use/user envi

21、ronment in order to restore serviceability to a failed item. (1) Source code.The source code tells you how to get the item needed for maintenance, repair, or overhaul of an end item/equipment. Explanation of source codes follows: CodeExplanation Stocked items: use the applicable NSN to request/requi

22、sition items with these source codes. They are authorized to the category indicated by the code entered in the third position of the SMR code. NOTE Items coded PC are subject to deterioration. 2 TM 11-5815-602-24P CodeExplanation Items with these codes are not to be requested/requisitioned individua

23、lly. They are part of a kit which is authorized to the maintenance category indicated in the third position of the SMR code. The complete kit most be requisitioned and applied. Items with these codes are not to be requested/requisitioned individually. They must be made from bulk material which is id

24、entified by the part number in the description and usable on code (UOC) column and listed in the Bulk Material group of the repair parts list. If the item is authorized to you by the third position of the SMR code. but the source code indicates it is made at a higher category, order the item from th

25、e higher category of maintenance. Items with these codes are not to be requested/requisitioned individually. The parts that make up the assembled item must be requisitioned or fabri- cated and assembled at the category of maintenance indicated by the source code. If the third position code of the SM

26、R code authorizes you to replace the item, but the source code indicates the item is assembled at a higher category, order the item from the higher category of maintenance. Code XA- Do not requisition an XB- If an “XB” item is CAGEC and part number Explanation “XA” coded item.Order its next higher a

27、ssembly. not available from salvage, order itusing the given. 3 TM 11-5815-602-24P XC- Installation drawing, diagram,instruction sheet, field service drawing, that is identified by manufacturers part number. XD -Item is not stocked. Order an “XD” coded item through normal supply channels using the C

28、AGEC and part number given, if no NSN is available. NOTE Cannibalization or controlled exchange, when authorized, may be used as a source of supply for items with the above source codes, except for those source coded “XA” or those aircraft support items restricted by requirements of AR 750-1 (2) Mai

29、ntenance code.Maintenance codes tell you the category of maintenance authorized to USE and REPAIR support items. The maintenance codes are entered in the third and fourth positions of the SMR code as follows: (a) The maintenance code entered in the third position tells you the lowest maintenance cat

30、egory authorized to remove, replace, and use an item. The maintenance code entered in the third position will indicate authorization to one of the following categories of maintenance. CodeApplication/Explanation C -Crew or operator maintenance done within organizational or aviation maintenance. O -O

31、rganizationalor aviation unit category can remove, replace, and use the item. F -Direct support or aviation intermediate category can remove, replace, and use the item. H -General support category can remove, replace, and use the item. L -Specialized repair activity can remove, replace, and use the

32、item. D -Depot category can remove, replace, and use the item. (b) The maintenance code entered in the fourth position tells whether or not the item is to be repaired and identifies the lowest maintenance category with the capability to do complete repair (i.e., perform all authorized repair functio

33、ns). This position will contain one of the following maintenance codes. NOTE Some limited repair may be done on the item at a lower category of maintenance, if authorized by the Maintenance Allocation Chart (MAC) and SMR codes. CodeApplication/Explanation O- Organizational or aviation unit is the lo

34、west category that can do complete repair of this item. F- Direct support or aviation intermediate is the lowest category that can do complete repair of the item. H- General support is the lowest category that can do complete repair of the item. 4 TM 11-5815-602-24P CodeApplication/Explanation L - D

35、 - Z - B - Specialized repair activity (designate the specialized repair activity) is the lowest category that can do complete repair of the item. Depot is the lowest category that can do complete repair of the item. Nonreparable.No repair is authorized. No repair is authorized. (No parts or special

36、 tools are authorized for the maintenance of a B coded item.) However the item may be reconditioned by adjusting, lubricating, etc., at the user category. (3) Recoverability code.Recoverability codes are assigned to items to indicate the disposition action on unserviceable items.The recoverability c

37、ode is entered in the fifth position of the SMR Code as follows: Recoverability. CodesApplication/Explanation Z - O - F- H- D - L - A - Nonreparable Item.When unserviceable, condemn and dispose of the item at the category of maintenance shown in the third position of the SMR code. Reparable item.Whe

38、n uneconomically repairable, condemn and dispose of the item at organizational or aviation unit category. Reparable item.When uneconomically repairable, condemn and dispose of the item at direct support or aviation intermediate category. Reparable item.When uneconomically repairable, condemn and dis

39、pose of the item at general support category. Reparable item.When beyond lower category repair capability return to Depot. Condemnation and disposal of item is not authorized below depot catagory. Repairable item. Condemnation and disposal not authorized below specialized repair activity (SRA). Item

40、 requires special handling or condemnation procedures because of specific reasons (e.g. precious metal content. high dollar value, critical material, or hazardous material). Refer to appropriate manuals/directives for specific instructions. c.(CAGEC(Column (3).The Commercial and Government Entity Co

41、de (CAGEC) is a 5-digit numeric code which is used to identify the manufacturer, distributor, or Government agency, etc., that supplies the item. d.Part Number (Column (4).Indicates the primary number used by the manufacturer(individual, company firm, corporation, or Government activity), which cont

42、rols the design and characteristics of the item by means of its engineering drawings, specifications,standards, and inspection requirements to identify an item or range of items. NOTE When you use an NSN to requisition an item, the item you receive may have a different part number from the part orde

43、red. 5 TM 11-5815-602-24P e.Description and Usable on Code (UOC)(Column (5).This column includes the following information. (1) The Federal item name and, when required, minimum description to identify the item. (2) Usable on code, when applicable (para 5). (3) In the Special Tools section, the basi

44、s of issue (BOI) last line in the entry for each special tool, special TMDE, and support equipment.When density of equipment supported exceeds indicated in the basis of issue,the total authorization proportionately. (4) The statement“END OF FIGURE” appears just below appears as the other special den

45、sity spread isincreased the last item description in Column (5) for a given figure in both section II and section III. f. Qty(Column (6).Indicates the quantity of the item used in the breakout shown on the illustration figure, which is prepared for a functional group, subfunctional group, or an asse

46、mbly.A “V” appearing in this column in lieu of a quantity indicates that the quantity is variable and the quantity may vary from application to application. 4. Explanation of Columns (Section IV) . National Stock Number (NSN) Index.a (2) Fig column.This column lists is identified/located.The illustr

47、at sections II and III. .The NIIN consists of the last nine (1) Stock number column.This column lists the NSN by National item identification number(NIIN)sequence digits of the NSN. When using this col four digits of the NSN. When requisi digits). umn to locate tioning items the number of ions are i

48、n an item, ignore the first use the complete NSN (13 the figure where the item numerical sequence in (3) Item column.The the item number identifies the item associated with the figure listed in the adjacent Fig. column. This item is also identified by the NSN listed on the same line. b.Part Number I

49、ndex.Part numbers in this index are listed by part number in ascending alphanumeric sequence. (1) CAGEC column.This column lists the Commercial and Government Entity Code (CAGEC). 6 TM 11-5815-602-24P (2) Part number column.This column indicates the part number assigned to the item. (3) Stock number column.This column lists the National stock number for the associated part number and the manufacturer identified in the part number and CAGEC columns to the left. (4) Figure column.This column lists the number of the figure where the item is identified/located i