Barrett_900_programming_user.pdf

《Barrett_900_programming_user.pdf》由会员分享，可在线阅读，更多相关《Barrett_900_programming_user.pdf（30页珍藏版）》请在收音机爱好者资料库上搜索。

1、PAGE 1 Barrett 900 Series Transceiver Programming Software Manual Barrett Communications BCM90001/1 Head office:European office: Barrett Communications Pty LtdBarrett Europe Limited 10 Port Kembla Drive, Bibra Lake WA 616319 Lenten Street P O Box 1214, Bibra Lake WA 6965Alton, Hampshire AUSTRALIAGU3

2、4 1HG Toll Free Tel: 1800 999 570UNITED KINGDOM Tel: (61-8) 9 434 1700Tel: (44) 1420 542254 Fax: (61-8) 9 418 6757Fax: (44) 1420 543373 BARRETT 900 SERIES PROGRAMING SOFTWARE BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 2 1.0Introduction 2.0Software Installation 3.0Operation 4.0Connection of the tran

3、sceiver to the programming PC 5.0Sending programming information to the transceiver .4 .4 .5 3.1Main Screen.5 3.1.1File Menu.5 3.1.2Clients (transceiver) Menu.6 3.1.3Transceiver Menu .7 3.2Configuration Options .8 3.3Adding / Editing a Client (transceiver).9 3.4Transceiver Configuration.11 3.4.1Oper

4、ational Parameters.11 3.4.1.1Configuration .11 3.4.1.2Hardware Options.13 3.4.1.3External Control Options.13 3.4.1.4Scanning.14 3.4.1.5Ext Alarm .14 3.4.1.6Clarifier Options.14 3.4.1.7Mute Setting.15 3.4.1.8Scan/ Selcall and SSL Settings.15 3.4.2Channel Parameters.16 3.4.2.1Channel Number.16 3.4.2.2

5、RX/TX Frequency .16 3.4.2.3Channel Label.17 3.4.2.4Channel Mode .17 3.4.2.5Selcall.17 3.4.2.6Selcall Type .18 3.4.2.7Channel Alarm Type .18 3.4.2.8Scanning.18 3.4.2.9Type.19 3.4.2.10Pre-programmed.19 3.4.2.11Low power .19 3.4.2.12All Modes.19 3.4.2.13Emergency Channel .19 3.4.2.14Antenna 2 .19 3.4.3

6、Display.20 3.4.3.1Display Options.20 3.4.3.3Back-light Level .21 3.4.4Locks .22 3.4.4.1Menu Locks .22 3.4.4.4Selcall Group Locks.23 3.4.4.4Mute Locks .23 3.4.4.5Mode Locks .23 3.4.5Other.24 3.4.5.1Labels.24 3.4.5.2TX Bands.24 .25 4.1Barrett 930, 950 and 980 .25 4.2Barrett 940.25 .25 BARRETT 900 SERI

7、ES PROGRAMING SOFTWARE PAGE 3 6.0Sending programming information from the transceiver 7.0Unlocking locked (killed) transceivers 8.0Programming a transceiver with the Cloning - Programming menu locked from users 9.0Trouble shooting 10.0Programming cable details .26 .27 .28 .28 .29 BARRETT 900 SERIES

8、PROGRAMING SOFTWARE PAGE 4 1.0Introduction 2.0Installation Barrett 900 series transceiver programming software enables simple management of 930, 940 and 950 transceiver configurations for multiple clients and transceiver configurations. The package is designed for use by Barrett dealers and network

9、managers. It can be loaded onto any PC that has a serial port and the minimum hardware configuration as listed at the rear of this manual. This manual describes how to load and start the software package. It also provides basic details on the programming package operation, more detailed operating in

10、structions are provided in the packages built in help function. Insert Setup disk 1 into floppy drive A: Go to the Start button on the task bar (Windows 95), and click on the Run. command. Type “A:setup.exe and press enter. Follow the on-screen prompts to install the software. Or go to windows explo

11、rer and double click on the “setup.exe” icon in the a: drive. Software BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 5 3.0Operation 3.1Main Screen When the user initially starts the program, the main user screen is displayed. This screen is used to control the client (transceiver) databases. The follo

12、wing section describes each menu option. This will create a new Barrett 900 series transceiver database with no clients in it. Use the Clients Menu to add, edit and delete clients (transceivers) to and from this database. This will open an existing Barrett 900 series transceiver database. If a Barre

13、tt 550 / DOS RadCfg database is selected you will be prompted to convert it. The new database created will be of the same name, but with the .MDB file extension. This will close the currently opened Barrett 900 series transceiver database. All edit features will be disabled until another Barrett 900

14、 transceiver database is opened. 3.1.1File Menu New Client (transceiver) List Open Client (transceiver) List Close Client (transceiver) List BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 6 Exit 3.1.2Clients (transceiver) Menu Add Client Edit Client Copy Client Delete Client Sort Method Print Client (t

15、ransceiver) List Copy Client (transceiver) to another Database This will exit the program, and close the open Barrett 900 series transceiver database. Adds a new client (transceiver) to the client database. You will be required to fill in the clients name, a unique serial number, selcall ids and tra

16、nsceiver pin number. This will allow you to edit the clients name, transceiver serial number, selcall ids and transceiver pin number. A client must be selected from the list. Copies the currently selected transceiver configuration to another client. This will delete a client from the client database

17、. This will select the method used to sort the clients (transceiver) list. Clicking the appropriate button above the client list can also access this function. This will print, to the selected printer, a list of all the clients in the currently open client (transceiver) list. This will copy the sele

18、cted client (transceiver) to another database. If the destination database does not exist, it will be created. If you wish to move the client (transceiver), use this option, then delete this client from the current database. BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 7 3.1.3Transceiver Menu Edit Se

19、nd Receive Print Send Blank Unlock Enables editing of the transceiver configuration for the currently selected client (transceiver). If the client (transceiver) has been newly created, then the transceiver configuration will be set to its default. Right clicking the mouse button in the client (trans

20、ceiver) list window can also access this function. This will send the transceiver configuration for the currently selected client to the Barrett 900 transceiver. The Barrett 900 transceiver will have to be setup to receive the configuration. Right clicking the mouse button in the client (transceiver

21、) list window can also access this function. This will receive the transceiver configuration from the Barrett 900 transeiver and write it to the currently selected client. Any existing configuration this client had in the database is deleted and overwritten. Right clicking the mouse button in the cl

22、ient (transceiver) list window can also access this function. This will print the Barrett 900 transceiver configuration for the currently selected client. This will send a blank pack to the Barrett 900 transceiver. This pack will contain all default configuration options. This is used to unlock the

23、transceiver, after a transceiver lock command was sent from the remote transceiver. BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 8 3.2Configuration Options To access the configuration options, go to the options menu on the main screen. After clicking on it, the following options are displayed:- This

24、is the serial port where the Barrett 900 transceiver is connected. Usually COM1 or COM2 depending on how the mouse, modem, or other peripherals are configured. Selects the windows printer device to print to. Selecting File as the printer here will prompt the user for a file name when any printing oc

25、curs in the program. Communication Port Printer BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 9 3.3Adding / Editing a Client (transceiver) To add a new client (transceiver), go to the Add Client menu option, in the Clients menu. To edit a client (transceiver) in the database, it is first necessary to

26、open a database file in the file menu. Then go to the Clients menu in the main user screen. Select the Edit Client menu option. The user is presented with the following options:- This is the clients name. The client name can be up to 30 characters. This is a unique transceiver serial number which yo

27、u can assign to the transceiver. If the serial number exists in the current database when you select close, you will be prompted to change it. This is the selective call ID for the clients transceiver which you can assign. This is usually unique to the client. The selcall ID is a 4 digit number. Cli

28、ent Serial No Selcall ID1 BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 10 Selcall ID2 Transceiver Pin Default Transceiver Pack Type This is the second selective call ID for the clients transceiver. The second Selcall ID is usually not used, and therefore set to the same as selcall ID1. Each transceiv

29、er channel can be set to use either selcall ID by default. This is a pin number that is used in the transceiver kill function. A confirmation pin is required to be entered below it. This must be an 8 digit pin number. Selects the default configuration options to send to the radio. These options can

30、be modified through the transceiver configuration dialog box. Selects the type of the transceiver to be programmed. BARRETT 900 SERIES PROGRAMING SOFTWARE PAGE 11 3.4Transceiver Configuration 3.4.1Operational Parameters Go to the Edit menu option in the Transceiver menu. This will edit the transceiv

31、er configuration for the currently selected client and transceiver. To edit the operational parameters, go to the operational tab in the configuration window. These options are used to initially configure the transceiver. Whether the client can change these options depends upon options set in Locks.

32、 Enables transmit frequency programming. Note:- if frequency ranges are specified in the “Band” section, transmit frequencies will only be allowed to be programmed from the front panel within these ranges. The purpose of the “Bands” section is to allow for instance only amateur band frequencies to b

33、e transmit frequency programmed. Note:- This feature may be used only where local laws and regulations allow. 3.4.1.1Configuration Transmit Frequency Programming BARRETT 900 SERIES PROGRAMING SOFTWARE Overwrite pre-programmed channels Marine Transceiver Noise blanker On Scrambler On Low Power On Tra

34、nsmit “over beeps” Emergency selcall Key “beeps” off Transmit timeout RS-232 selcall output Mic up/down enable External GPS When overwrite is enabled the client will be able to change pre-programmed channels, Effectively this will allow the client to program all channels. If this option is not enabl

35、ed the client will only be able to program empty channels and channels that do not have the pre- programmed option set. When this check-box is enabled any channels programmed by the client will default as marine channels. This means that the clarifier for the channel will be 150Hz, unless the channe

36、l is programmed to be a selcall channel. If this option is enabled the noise blanker circuitry will be turned on. When disabled the noise blanker will be turned off. If this option is enabled the scrambler circuitry will be turned on. When disabled the scrambler will be turned off. The Scrambler Fit

37、ted option must also be set. If this option is enabled the transceiver will transmit in low power mode on all channels. If not enabled the transceiver will transmit at the default power programmed in each channel. If this option is enabled, when PTT is released a quick “over beep” is transmitted on

38、air. This option, when enabled, allows the transceiver to receive and transmit emergency selcalls. Note:- Emergency selcall status can be assigned to any channel in the channel programming setup. If this option is enabled beeps are not emitted when the user presses the front panel keys. This option

39、turns the transmitter off if the microphone PTT is held activated (i.e. wedged in a car seat) for more than 1.5 minutes. If this option is enabled a sentence will be output to the RS-232 port when the transceiver receives a selcall or telcall. Also the transceiver will not audibly annunciate the reception of a selcal