Icom_IC-F43GT_IC-F43GS_IC-F44GT_IC-F44GS_user.pdf

《Icom_IC-F43GT_IC-F43GS_IC-F44GT_IC-F44GS_user.pdf》由会员分享，可在线阅读，更多相关《Icom_IC-F43GT_IC-F43GS_IC-F44GT_IC-F44GS_user.pdf（48页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL iF43GT/GS UHF TRUNKED RADIOS iF44GT/GS R CAUTION! NEVER hold the transcever so that the antenna s very close to, or touchng exposed parts of the body, especally the face or eyes, whle transmttng. The transcever wll perform best f the mcrophone s 5 to 10 cm away from the lps and th

2、e transcever s vertcal. R CAUTION! NEVER operate the transcever wth a headset or other audo accessores at hgh volume levels. R CAUTION! NEVER short the termnals of the bat- tery pack. DO NOT push PTT when not actually desrng to transmt. DO NOT use or place the transcever n drect sunlght or n areas w

3、th temperatures below 25C or above +55C. The basc operatons, transmsson and recepton of the transcever are guaranteed wthn the specfed operatng temperature range. However, the LCD dsplay may not be operate correctly, or show an ndcaton n the case of long hours of operaton, or after beng placed n ext

4、remely cold areas. PRECAUTIONSIMPORTANT READ ALL INSTRUCTIONS carefully and com- pletely before usng the transcever. SAVE THIS INSTRUCTION MANUAL Ths nstructon manual contans mportant operatng nstructons for the IC-F43GT/GS, F44GT/GS UHF TRUNKED RADIOS. EXPLICIT DEFINITIONS WORDDEFINITION RDANGER Pe

5、rsonal death, serous njury or an exploson may occur. RWARNING Personal njury, fre hazard or electrc shock may occur. CAUTION Equpment damage may occur. NOTE If dsregarded, nconvenence only. No rsk of personal njury, ire or electrc shock. Icom, Icom Inc. and the Icom logo are regstered trademarks of

6、Icom Incor- porated (Japan) n the Unted States, the Unted Kngdom, Germany, France, Span, Russa and/or other countres. DO NOT modfy the transcever for any reason. KEEP the transcever from the heavy ran, and Never m- merse t n water. The transcever constructon s water re- sistant, not waterproof. The

7、use of non-Icom battery packs/chargers may mpar transcever performance and nvaldate the warranty. Icom optonal equpment s desgned for optmal perfor- mance when used wth ths transcever. We are not respon- sble for the transcever beng damaged or any accdent caused when usng non-Icom optonal equpment.

8、TABLE OF CONTENTS IMPORTANT . EXPLICIT DEFINITIONS . PRECAUTIONS . TABLE OF CONTENTS . 1 ACCESSORIES .13 Suppled accessores .1 Accessory attachments .1 2 PANEL DESCRIPTION .46 Front panel .4 Functon dsplay .6 3 BASIC OPERATION .720 General.7 Callng .8 Callng wth the keypad (10-key verson only) .12 S

9、pecal call wth the keypad .17 Recevng a call .17 4 DISPLAYING MESSAGES .21 5 OTHER FUNCTIONS .2225 PTT quck call .22 Call back functon .22 Callng staton ID ndcaton for group call .23 System lock functon .24 Call code memory .24 Automatc transmt output power selecton .24 Power ON securty.24 Voce scra

10、mbler .25 DTMF operaton .25 Compander functon .25 6 USER SET MENU .2627 User set menu .26 7 TALK AROUND .28 8 PROGRAMMABLE FUNCTIONS.2930 Programmable functon keys .29 9 OPTIONAL UNIT INSTALLATION .31 UT-109 and UT-110 nstallaton .31 10 BATTERY CHARGING .3236 Cauton .32 Optonal battery chargers .34

11、11 OPTIONAL BATTERY CASE .37 Battery case (BP-240) .37 12 OPTIONAL SWIVEL BELT CLIP .3839 MB-93 contents .38 Attachng .38 Detachng .39 13 OPTIONS .4041 14 DOC .42 Supplied accessories The followng accessores are suppled: Qty. q Flexble antenna .1 w Battery pack .1 e Belt clp .1 r Unt cover (double-s

12、ded tape)* .1 t Jack cover (wth screws) .1 set *Use the unt cover as a spare. Ask your dealer for detals. qw r e t Accessory attachments D Flexible antenna Connect the suppled flexble an- tenna to the antenna connector. CAUTION: NEVER HOLD the antenna when carryng the transcever. Transmttng wthout a

13、n antenna may damage the transcever. 1 1 ACCESSORIES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 2 1ACCESSORIES D Battery pack To attach the battery pack: Slde the battery pack n the drecton of the arrow (q), then lock t wth the battery release button. Slde the battery pack untl the battery release butto

14、n makes a clck sound. To release the battery pack: Push the battery release button n the drecton of the arrow (w) as shown below. The battery pack s then released. NEVER release or attach the battery pack when the trans- cever s wet or soled. Ths may result water or dust get- tng nto the transcever/

15、battery pack and may result n the transcever beng damaged. q w D Belt clip To attach the belt clip: q Release the battery pack f t s attached. w Slde the belt clp n the drecton of the arrow untl the belt clp s locked and makes a clck sound. To detach the belt clip: q Release the battery pack f t s a

16、ttached. w Pnch the clp (q), and slde the belt clp n the drecton of the arrow (w). q w D Jack cover Attach the jack cover when the optonal speaker-mcrophone s not used. To attach the jack cover: q Attach the jack cover on the SP/MIC jack. w Tghten the screws. To detach the jack cover: q Unscrew the

17、screws wth a Phllps screwdrver. w Detach the jack cover for the speaker-mcrophone connecton. q w q w 3 1ACCESSORIES 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 4 2 PANEL DESCRIPTION Front panel q w e r t u 10-keypad version y i o !0 !1 !2 !3 Function display (p. 6) q GROUP SELECTOR Rotate to select the p

18、re-programmed group code chan- nel. w VOLUME CONTROL VOL Rotate to turn the power ON/OFF and adjusts the audo level. e EMERGENCY KEY RED Push and hold for 2 sec. to start the emergency call to the specied number (Emergency call; p. 15). “EMRGENCY” s dsplayed whle pushng and holdng. r SP/MIC JACK Con

19、nect the optonal speaker-mcrophone. SP/MIC jack cover NOTE: Attach the SP/MIC jack cover when the optonal speaker- mcrophone s not used. (See p. 3 for detals) t MODE KEY P2 (p. 28) Push to toggle between conventonal and trunkng opera- ton modes. y HIGH/LOW KEY P3 Push to toggle the transmt output po

20、wer. When automatc power selecton s enabled for trunkng mode operaton, the transmt output power cannot be selected wth ths key. u 10-KEYPAD (Dependng on verson) The keypad allows you to enter dgts to: Set TX codes Set DTMF codes (durng transmt) Input text message for SDM operaton Start up wth the pa

21、ssword i DESPATCHER KEY P0 (p. 10) Push to dsplay despatcher call condtons. Push agan to dsplay the status code, f permtted. Push agan to return to stand-by condton. o CALL BACK KEY P1 (p. 22) Push to dsplay the receved call record (call back mem- ory) that had not repled. Push agan to return to sta

22、nd-by condton. Push and hold for 2.5 sec. to toggle the call back mode ON and OFF. When the call back mode s set to ON, the receved call s stored nto record (log), and the call back message s send back to the callng staton automatcally. !0 UP/DOWN KEYS Push to select the call memory channel. Push to

23、 select the call back memory channel. Push to select the status channel. Push to select the operatng channel. (Conventonal mode operaton only) Push to select the settng value or condton durng user set mode. Push to erase the prevously entered dgt number (functons as back space key) durng dalng numbe

24、r enterng from the keypad. (10-key verson only) !1 PTT SWITCH PTT Push to makng a call wth the dsplayed dalng num- ber. When selectng a trafic channel for communcaton, or conventonal mode, push to transmt. When an ndvdual call s receved, push to reply the call. !2 CLEAR (SET MODE) KEY (pgs. 8, 26) P

25、ush to insh the communcaton. Push and hold to enter to the user set menu. Durng some functon operaton, push to return to stand- by condton. !3 ANTENNA CONNECTOR Connects the suppled antenna. Desred functons can be programmed nto the P0 to P3, Red, Clear, Up and Down keys ndependently by your dealer.

26、 (p. 29) 5 2PANEL DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 6 2PANEL DESCRIPTION Function display q!1!0oiuytrew !2 !3 !4 q TRANSMIT INDICATOR Appears whle transmttng. w BUSY INDICATOR Appears whle the channel s busy. e OVER-FLOW INDICATOR Appears when the receved SDM ncludng more than 9 cha

27、racters s dsplayed. r SIGNAL STRENGTH INDICATOR Appears when recevng a sgnal and shows the sgnal strength levels n 4-steps. No bars appear and “” blnks when the transcever s n out-of servce area. For stable communcatons, the transcever should be n the area that the S-meter ndcator shows the full sca

28、les (3 bars) ndcaton. t LOW POWER INDICATOR Appears when low output power s selected. When the battery power decreases to a specied level, low power s selected automatcally. y AUDIBLE INDICATOR Appears when the voce communcaton can be per- formed. u COMPANDER INDICATOR Appears when the compander fun

29、cton s actvated. The compander functon mproves communcatng audo qualty. i SCRAMBLER INDICATOR Appears when the voce scrambler functon s actvated. o CALL BACK INDICATOR Blnks when an ndvdual call s receved. Appears when ndvdual calls that the call back opera- ton has not been performed are avalable.

30、Dsappears when reples to all ndvdual calls. !0 PRIMARY NETWORK INDICATOR Appears when the transcever s n the prmary network servce area. !1 KEY LOCK INDICATOR Appears when the key lock functon s turned ON. !2 BATTERY INDICATOR Appears or blnks when the battery power decreases to a specied level. !3

31、ALPHANUMERIC DISPLAY Shows dalng number and receved message, etc. !4 SYSTEM LOCK INDICATOR Appears when the system lock functon s n use. General Rotate VOL to turn the transcever power ON. Beeps sound, and the followng contents wll be dsplayed n sequence. Opening text Preix code (3-dgt)/Fleet code (

32、4-dgt) Individual code (2 or 3-dgt) Memory group code (or text name) - The selected memory group code (selected by Group se- lector) and “” are dsplayed when the transcever s n the trunkng servce area, and the desred call can be made. (The text name s dsplayed f programmed nstead of the group code.)

33、 - “” blnks when the transcever s n out-of-servce area, or the system s fall down. The transcever searchng for an operatable system base n ths case. - “” appears when the control sgnal from the base staton that the system ID (AAD number) s regstered n prmary network. e.g.: When the Preix code s 201,

34、 Fleet code s 2001, Ind- vdual code s 300 and Group code s 90, “201/2001”, “300” and “90” are dsplayed n sequence after turnng the transcever ON. (Openng text) Openng text s dsplayed. 201/2001 Preix code/Fleet code s ds- played. 300 Indvdual code s dsplayed. 90 A group code s dsplayed when no text n

35、ame s pro- grammed. 7 3 BASIC OPERATION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 8 3BASIC OPERATION Calling The followng call operatons can be performed usng the pre- programmed dalng number. D Group call Select the desred group code that s stored n the memory usng Group selector or Up/Down. Up to 16

36、group codes wth Group selector, up to 40 group codes wth Up/Down can be selected. q Rotate Group selector or Up/Down to select the de- sred group code. GROUP 1 The pre-programmed text name s dsplayed. 90 When no text name s pro- grammed, a group code s dsplayed. w Push PTT or Call Set Up to make a g

37、roup call. “CALLING” s dsplayed and the callng beeps sound. CALLING e When the call s succeeded, “CONNECT” and “ ” appear, and communcaton can be made. The communcaton tmer starts count down at the same tme. (When no transmsson tme lmt s set, the tmer counts up.) CONNECT TIM 0 56 r The warnng beeps

38、sound 10 sec. before the communca- ton tmer s actvated. The communcaton s dsconnected automatcally when the communcaton tmer s actvated. t Push Clear to dsconnect the communcaton manually. Pushng M and # n sequence also dsconnect the commun- caton. (10-key verson only) CLR DOWN D Individual call Sel

39、ect the desred ndvdual code wth Up/Down. q Push Up/Down to select the desred ndvdual code. PERSON 1 The pre-programmed text name s dsplayed. 20 302 When no text name s pro- grammed, the dalng num- ber s dsplayed. w Push PTT or Call Set Up to make an ndvdual call. “CALLING” s dsplayed and callng beep

40、s sound. CALLING e When the call s succeeded, “CONNECT” and “ ” appear, and communcaton can be made. The communcaton tmer starts count down at the same tme. (When no transmsson tme lmt s set, the tmer counts up.) CONNECT TIM 0 56 r The warnng beeps sound 10 sec. before the communca- ton tmer s actvated. The communcaton s dsconnected automatcally when the communcaton tmer s actvated. t Push Clear to dsconnect the communcaton manually. Pushng M and # n sequence also dsconnect the commun- caton. (10-key verson only) CLR DOWN 9 3BASIC OPERATION 1 2 3 4 5 6 7 8 9 10 11 12 13 1