Icom_IC-F8101_user.pdf

《Icom_IC-F8101_user.pdf》由会员分享，可在线阅读，更多相关《Icom_IC-F8101_user.pdf（88页珍藏版）》请在收音机爱好者资料库上搜索。

1、HF TRANSCEIVER iF8101 INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. i FOREWORD Thank you for purchasing this Icom product. The IC- F8101 HF TRANSCEIVER is designed and built with Icom

2、s state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. We appreciate you making the IC-F8101 your radio of choice, and hope you agree with Icoms philosophy of “technology fi rst.” Many hours of research and develop- me

3、nt went into the design of your IC-F8101. D FEATURES ALE (Automatic Link Establishment)/Sel- call capability Digital Signal Processor (DSP) allows fl ex- ible fi lter selection Full-dot matrix LCD for a variety of infor- mation IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to op

4、erate the transceiver. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating in- structions for the IC-F8101. EXPLICIT DEFINITIONS WORDDEFINITION R DANGER! Personal death, serious injury or an explosion may occur. R WARNING! Personal injury, fire hazard or electric shock

5、may occur. CAUTIONEquipment damage may occur. NOTE Recommended for optimum use. No risk of personal injury, fire or electric shock. Versions of the IC-F8101 which display the “N33” symbol on the serial number seal, comply with Standard Australia Specifi cation No. AS/NZS 4770: 2000. Icom, Icom Inc.

6、and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. FCC INFORMATION FOR CLASS

7、 A UNINTENTIONAL RADIATORS: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer- ence when the equipment is operated in a commercial

8、environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica- tions. Operation of this equipment in a residential area is likely to cause harmful interfe

9、rence in which case the user will be required to correct the interference at his own expense. CAUTION: Changes or modifi cations to this trans- ceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. ii FOREWORD . i IMPORTANT . i EXPL

10、ICIT DEFINITIONS . i FCC INFORMATION . i TABLE OF CONTENTS .ii SAFETY TRAINING INFORMATION .iii INFORMATION EN MATIRE DE SCURIT .iv PRECAUTIONS . v 1 PANEL DESCRIPTION .16 Controller (Front panel or HM-192) .1 Rear panel .4 LCD screen .5 2 BASIC OPERATION .710 Power ON .7 Selecting the display mode

11、.7 Selecting a channel .8 Setting audio volume .8 Squelch function .8 Scan function .9 Mode selection .9 VFO operation .10 3 RECEIVE AND TRANSMIT .1117 Basic voice transmit/receive .11 Functions for transmit .12 Functions for receive .14 4 SELCALL/ALE OPERATION .1832 Selcall/ALE .18 5 MENU SCREEN .3

12、365 Manager Menu .33 Main Menu .46 CPU Reset .65 6 CONNECTION AND INSTALLATION .6679 Supplied accessories .66 Connections .68 Ground connection .70 Power source .71 Antenna .71 CFU-F8100 (Optional Cooling Fan) .71 RMK-6 (Optional Separation kit) .72 HM-192 (Optional Remote control microphone) .74 Mo

13、unting .75 Fuse replacement .77 Connector information .78 Connector information for OPC-2308 .79 7 SPECIFICATIONS .80 8 OPTIONS .81 TABLE OF CONTENTS 1 2 3 4 5 6 7 8 iii SAFETY TRAINING INFORMATION WARNING Your Icom radio generates RF electromag- netic energy during transmit mode. This radio is desi

14、gned for and classifi ed as “Oc- cupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT intended for use by the “General Population” in an uncontrolled en- vironment. Forcomplian

15、cewithFCCandICRFExposureRe- quirements, the transmitter antenna installation shall comply with the following two conditions: 1. The transmitter antenna gain shall not exceed 0 dBi. 2. The antenna is required to be located outside of a vehicle and kept at a distance of 80 centime- ters or more betwee

16、n the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the centre line along the vehicle in order to achieve 80 cen- timeters separation distance. In order to ensure this distance is me

17、t, the installation of the antenna must be mounted at least 80 centimeters away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 3. Transmit only when people outside the vehicle are at least the recommended minimum distance of 160 centimeters away from the pro

18、perly installed antenna. This separation distance will ensure that there is suffi cient distance from a properly installed externally-mounted antenna to satisfy the RF ex- posure requirements in the applicable RF exposure compliance standards. CAUTION To ensure that your exposure to RF electromagnet

19、ic energy is within the FCC and IC allowable limits for occupa- tional use, always adhere to the follow- ing guidelines: DO NOT operate the radio without a proper antenna attached, as this may damage the radio and may also cause you to exceed FCC and IC RF exposure limits. A proper antenna is the an

20、tenna supplied with this radio by the manufacturer or an antenna specifi - cally authorized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (“50% duty cycle”). Transmitting more than 50% of the time can cause FCC and IC RF exposure compliance re

21、quirements to be exceeded. The radio is transmitting when the “TX” icon is displayed. You can cause the radio to transmit by pressing the “PTT” switch. Electromagnetic Interference/Compatibility During transmissions, your Icom radio generates RF energy that can possibly cause interference with other

22、 devices or systems. To avoid such interference, turn OFF the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospi- tals, aircraft, and blasting sites. iv INFORMATION EN MATIRE DE SCURIT AVERTISSEMENT Vo

23、tre radio Icom produit une nergie lectromagntique de radiofrquen- ces (RF), en mode de transmission. Cette radio est conue pour un usage professionnel seulement et classe comme tel, ce qui signifi e quelle doit tre utilise uniquement dans le cadre dun travail par des personnes conscientes des danger

24、s et des mesures visant minimiser ces dangers. Elle NEST PAS conue pour une utilisation grand public, dans un environnement non contrl. AfindesatisfaireauxexigencesdelaFCCetdIC en matire dexposition aux RF, il est ncessaire que lantenne soit installe conformment aux trois conditions suivantes: 1. Le

25、 gain de lantenne du radio metteur ne doit pas dpasser 0 dBi. 2. Il faut que lantenne mettrice de cet appareil soit place lextrieur dun vhicule et tenue loigne dau moins 80 centimtres de toute per- sonne pendant le fonctionnement. Dans le pire des cas, pour un petit vhicule, lantenne doit tre place

26、sur le toit, nimporte o dans laxe central du vhicule, afi n de respecter une distance de 80 cm du bord le plus rapproch du vhicule et ainsi viter que les personnes prsentes soient expo- ses. 3. mettre uniquement lorsque les personnes lextrieur du vhicule se trouvent au moins la distance minimale rec

27、ommande de 160 cm de lantenne correctement installe. Cette distance de scurit assurera que les personnes soient places suffi samment loin dune antenne correcte- ment fi xe lextrieur pour satisfaire aux exigen- ces en matire dexposition aux RF, en vertu des normes de conformit applicables. MISE EN GA

28、RDE Afi n de vous assurer que votre expo- sition une nergie lectromagnti- que de RF se situe dans les limites permises par la FCC et dIC pour une utilisation grand public, veuillez en tout temps respecter les directives suivantes: NE PAS faire fonctionner la radio sans quune antenne approprie y soit

29、 fixe, car ceci risque dendommager la radio et causer une exposition suprieure aux limites tablies par la FCC et dIC. Lantenne approprie est celle qui est fournie avec cette radio par le fabricant ou une antenne spcia- lement autorise par le fabricant pour tre utilise avec cette radio. NE PAS mettre

30、 pendant plus de 50 % du temps total dutilisation de lappareil (50 % du facteur dutilisation). mettre pendant plus de 50 % du temps total dutilisation peut causer une exposi- tion aux RF suprieure aux limites tablies par la FCC et dIC. La radio est en train dmettre lors- que le tmoin du mode de tran

31、smission saffi che sur lcran ACL. La radio mettra si vous appuyez sur le bouton du microphone. Interfrence lectromagntique et compatibilit En mode de transmission, votre radio Icom produit de lnergie de RF qui peut provoquer des interfrences avec dautres appareils ou systmes. Pour viter de telles in

32、terfrences, mettez la radio hors tension dans les secteurs o une signalisation lexige. NE PAS faire fonctionner lmetteur dans des secteurs sensibles au rayonnement lectromagntique tels que les hpi- taux, les aronefs et les sites de dynamitage. v PRECAUTIONS R DANGER HIGH RF VOLTAGE! NEVER attach an

33、antenna or internal antenna connector during trans- mission. This may result in an electrical shock or burn. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a

34、ringing in your ears, reduce the volume or discontinue use. R WARNING! NEVER operate or touch the trans- ceiver with wet hands. This may result in an electric shock or damage to the transceiver. R WARNING! NEVER apply AC power to the DC13.8V socket on the transceiver rear panel. This could cause a f

35、ire or damage the transceiver. R WARNING! NEVER apply more than 16 V DC to the DC13.8V socket on the transceiver rear panel, or use reverse polarity. This could cause a fire or damage the transceiver. R WARNING! NEVER let metal, wire or other objects protrude into the transceiver or into connectors

36、on the rear panel. This may result in an electric shock. R WARNING! ALWAYS use the supplied Black and red cables with fuse holders. After connecting the fuse holders, NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver m

37、ight be damaged. R WARNING! Immediately turn OFF the transceiver power and remove the power cable if it emits an abnor- mal odor, sound or smoke. Contact your Icom dealer or distributor for advice. CAUTION: NEVER change the internal settings of the transceiver. This may reduce transceiver performanc

38、e and/or damage to the transceiver. In particular, incorrect settings for transmitter circuits, such as output power, idling current, and so on, might damage the expensive final devices. The transceiver warranty does not cover any problems caused by unauthorized internal adjustment. CAUTION: NEVER i

39、nstall the transceiver in a place without adequate ventilation. Heat dissipation may be reduced, and the transceiver may be damaged. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 30C (22F) or above +60C (+140F). The basic operations, transmission and rece

40、ption of the transceiver are guaranteed within the specified operat- ing temperature range. However, the LCD display may not be operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. DO NOT use harsh solvents such as benzine or

41、 alco- hol when cleaning, as they will damage the transceiver surfaces. DO NOT push the PTT switch when you dont actually desire to transmit. DO NOT place the transceiver against walls or putting anything on top of the transceiver. This may overheat the transceiver. Always place unit in a secure pla

42、ce to avoid inadvertent use by children. BE CAREFUL! If you use a linear amplifier, set the transceivers RF output power to less than the linear amplifiers maximum input level, otherwise, the linear amplifier will be damaged. BE CAREFUL! The transceiver will become hot when operating the transceiver

43、 continuously for long periods of time. USE only the specified microphone. Other manufactur- ers microphones have different pin assignments, and connection to the IC-F8101 may damage the transceiver or microphone. During mobile operation, NEVER place the transceiver where air bag deployment may be obstructed. During mobile operation, DO NOT place the transceiver where hot or cold air blows directly onto it. During mobile opera