Motorola_T80_T80-Extreme_user.pdf

《Motorola_T80_T80-Extreme_user.pdf》由会员分享，可在线阅读，更多相关《Motorola_T80_T80-Extreme_user.pdf（164页珍藏版）》请在收音机爱好者资料库上搜索。

1、T80/T80 EXTREME OWNERS MANUAL ENFRITESDE SV NOTU SF RUPL PRNLDA 1 1 English PRODUCT SAFETY AND RF EXPOSURE FOR PORTABLE TWO-WAY RADIOS ATTENTION! Before using this product, read the RF energy awareness information and operating instructions in the Product Safety and RF Exposure booklet to ensure com

2、pliance with RF energy exposure limits. Package Contents 2 x TLKR T80/T80 Extreme Radio 2 x Belt Clip 1 x 2-Slot Charging Cradle 1 x AC Adapter 2 x Battery support brackets 2 x Rechargeable NiMH battery packs 2 x Headset (for T80 Extreme Only) 2 x Lanyard (for T80 Extreme Only) TLKR T80/T80 Extreme

3、Owners Manual Frequency Chart Features and Specifications 8 PMR Channels 121 Sub-Codes (38 CTCSS Codes charge the radio or replace batteries immediately. (The alert tone sounds every 5 seconds for 30 seconds when the battery is low.) English 4 Using the Battery Support Bracket : 1. Remove the rechar

4、geable NiMH battery pack from the radio. 2. Place the battery support bracket into the charging cradle. 3. Install the NiMH battery pack into the charging cradle. Ensure that the charging contacts are correctly aligned. 4. LED indicator will illuminate and remain illuminated as long as the radio is

5、in the charger. Note: Charge the battery pack for 14 hours. Basic Radio Operations Read this reference guide completely before attempting to operate the unit. Turning your Radio On/Off To turn your radio ON, turn the rotary knob clockwise. To turn your radio OFF, turn the rotary knob counterclockwis

6、e. Adjusting the Volume Increase volume by turning the rotary knob clockwise. To decrease volume, turn the rotary knob counterclockwise. Adjusting the Sound (Key Beeps) Your radio emits a beep each time one of the buttons is pressed (except the PTT and button). Press and hold the button while turnin

7、g the radio ON to switch the sound ON/OFF. Navigating through the Menu Your radios has two Menu functions: Select Menu and Common Menu. 1. To enter the Select Menu, press the SEL/ button. 2. To enter the Common Menu, press the MENU/GRP button. 3. Additional presses of the SEL/ button or MENU/GRP but

8、ton will advance you through the Menu. 4. To exit the Menu function, do one of the following : a. Press the MENU/GRP button, b. Press the PTT button c. Wait 10 seconds until the unit automatically returns to “Normal” mode. Talking on Your Radio 1. Hold your radio 58 cm from your mouth. 2. Press and

9、hold the PTT button while speaking. The appears on the display. 3. Release the PTT button. You can now receive incoming calls. When you do, the appears on the display. To respond, repeat procedure from step 1. Note: When you continue to transmit for 60 seconds, the radio emits TX Time Out tone and t

10、he icon flashes. The radio will stop transmitting. In order to speak to someone, both your radios must be set to the same channel and Sub-Code. Refer to “Selecting a Channel and a Sub-Code” below. Selecting a Channel and a Sub-Code To select a Channel: 1. SEL/ button to enter Select Menu. Advance un

11、til the Channel indicator blinks. 2. or to the required channel. To select a Sub-code : 1. SEL/ button to enter Select Menu. Advance until the Sub-code indicator blinks. 2. or to the required Sub-code. 3. Exit the Select Menu. 5 English Select Menu Your radio navigates through the Select Menu as fol

12、lows: Voice Operated Transmission (VOX) Transmission is initiated by speaking into the microphone of radio instead of the pushing the PTT button. To select the VOX level: 1. MENU/GRP button to enter Common Menu. Advance and select “VOX”. 2. SEL/ to select. 3. or to the desired VOX sensitivity level.

13、 4. Exit the Select Menu. Note: Level “N”(OFF) disables VOX. Levels 1-5 set the sensitivity of the VOX circuit.Use level 1 in quiet environments, and use level 5 in very noisy environments. You can find the appropriate sensitivity level by speaking into the microphone. If the flashes, your voice is

14、accepted. Transmitting a Call Tone Your radio is equipped with 10 selectable call tones . To select a call tone: 1. MENU/GRP button to enter Common Menu. Advance to “TONE”. 2. SEL/ to select. 3. or to the desired call tone. 4. Exit the Common Menu. To transmit the selected call tone : 1. to transmit

15、 the selected call tone. The selected tone will automatically be transmitted for a fixed length of time. 2. PTT to cancel Call Tone. Auto Power Off Auto Power Off feature allows you to set the time that the radio turns off automatically. 1. MENU/GRP button to enter Common Menu. Advance until “PWR” a

16、nd the current Auto Power Off time blinks. 2. SEL/ to select. 3. or to select the time from ON, 1H, 2H, and 3H. 4. Exit the Menu. NormalChannelSub-code 1 - 80 - 121 English 6 Common Menu Your radio navigates through Common Menu as follows: Group Menu 1. Press and hold MENU/GRP to enter GROUP MENU. 2

17、. or to proceed to each menu (GRP/CODE/RING/ID). 3. SEL/ to select. 4. or to proceed to desired condition or number. 5. SEL/ to select. 6. MENU/GRP to exit. Set Group Mode 1. Press and hold MENU/GRP to enter GROUP MENU. 2. SEL/ to control Group Mode. 3. or to “Y”. SEL/ to go to Group Menu and Group

18、Code Setting. 4. or to “N”. SEL/ to exit from Group Menu. Up Timer Mode Select the Sensitivity (1-5) Normal SCAN 2CH (Dual Watch) VOX ROOM (Room Monitor) TONE (Call Tone) SLNT (Silent) TIME (Up Timer) PWR (Power) Select the Channel and Sub-Code Dual Watch Mode Off 1-5 Scan Mode 1 - 10“N” or “Y” Sele

19、ct the ON/ 1H/2H/3H Room Monitor Mode Normal “GRP” (Group Mode) “CODE” (Group Code) “RING” (Ring Tone) “ID” (ID Setting) “N” or “Y”0 - 1211-10 ID Number 1-16 ID Name Up to 4 Characters “Y” 7 English Set Group Code 1. or to choose the Group Code. 2. SEL/ to complete Group Code setting. 3. The radio e

20、nters “Ring Tone Setting Menu” 4. MENU/GRP to back to Group Menu. Set Ring Tone The user can select the Ring Tone for a Direct Call. Ring Tones are the same as Call Tones. 1. or to select a Ring Tone. 2. The selected Ring Tone sounds. Set ID Each radio in the group needs to be set with an ID. The us

21、er can set an ID name of up to four (4) characters. 1. or to select an ID number. 2. If the ID is already taken, USED is seen. If USED is not shown, then the ID is available. 3. SEL/ to advance to setting ID Name. Set ID Name The ID Name appears on the other radios display when you make an All Call

22、or a Direct Call. The ID Name will also on the other radios display when they are placing a Direct Call. When no ID name is set, the unit number appears. 1. or to select a character that will blink on the display. 2. SEL/ to select and move to the next character. 3. SEL/ to register the ID number an

23、d ID Name. Note: The radio cancels selected ID Number and entered ID Name, then exits from Group Menu when MENU/GRP button is pressed. Channel Setting in Group Mode To set Auto Channel Change in Group Mode: 1. MENU/GRP to enter Group Mode. 2. SEL/ to enter Channel Setting. 3. or to “Auto Channel Cha

24、nge Setting”. 4. SEL/ to select. A channel number will blink and “ALL” is seen. 5. or to select the channel. 6. SEL/ or to transmit Auto Channel Change command. 7. MENU/GRP to return to Channel Setting in Group Mode. To set Manual Channel in Group Mode: 1. MENU/GRP to enter Group Mode. 2. SEL/ to en

25、ter Channel Setting. 3. or to “Manual Channel Setting”. 4. SEL/ to select. A channel number will blink and “MY” is seen. 5. or to select the channel manually. 6. SEL/ to exit from Manual Channel setting. 7. MENU/GRP to return to Channel Setting in Group Mode. Set All Call 1. MENU/GRP to enter Group

26、Mode. 2. to enter All/ Direct Call Setting. 3. or to select All Call Transmission. “SYNC” is seen. 4. SEL/ or to exit this setting, and transmit All Call. All Call Tone sounds. and blinks while transmitting. 5. MENU/GRP to exit. English 8 Set Direct Call 1. MENU/GRP to enter Group Mode. 2. to enter

27、All/ Direct Call Setting. 3. or to select an ID Number. 4. or SEL/ to transmit Direct Call Command. The selected Call Tone sounds. The display shows TX icon and CALL icon while transmitting. 5. MENU/GRP to go back to All/Direct Call setting. Features on Your Radio Channel Scan Mode Enables your radi

28、o to scan for active channels. When activity is detected, your radio lands (stays) on that channel for 2 seconds (5 seconds for VOX ON without headset). To transmit on that channel, press the PTT button. When activity on the landed channel ends, your radio continues scanning other channels. To turn

29、the channel scan ON: 1. MENU/GRP to enter Common Menu. Advance to ”SCAN”. 2. SEL/ to turn ON channel scan. 3. MENU/GRP or PTT to turn OFF Scan mode. Dual Watch Mode Enables your to scan the current channel and another channel alternately. To set another channel and start Dual Watch: 1. MENU/GRP to e

30、nter Common Menu. Advance to “2CH”. 2. or to select the channel, then press SEL/ . 3. or to select the Sub-code, then press SEL/ . 4. The radio starts to Dual Watch. Note: If you set the same channel and Sub-code as the current channel, Dual Watch doesnt work. 5. MENU/GRP to turn the Dual Watch mode

31、 OFF. Room Monitor Enables your radio to detect voice/noises (according to the sensitivity level set) and transmit back to the listening radio without pushing the PTT button. The monitoring radio is not able to receive any transmissions in this mode. To turn Room Monitor ON: 1. MENU/GRP to enter Com

32、mon Menu. Advance to “ROOM”. 2. SEL/ to select. 3. or to the desired room monitor sensitivity level. Note: Use level 1 in quiet environments. Use level 5 in very noisy environments. 4. SEL/ to turn ON room monitor. MENU/GRP to turn OFF Room Monitor. Note: When the voice/noise in the monitored room c

33、ontinues for more than 60 seconds, the monitoring radio stop monitoring for 5 seconds, and resumes. The ID Number for Direct Call The ID Name 9 English Silent Mode Silent mode will mute all incoming calls. The backlight of the radio blinks when theres an incoming call. If the call is not answered, t

34、he backlight turns off and the blinks until there is no signal. The T80/T80 Extreme radio will vibrate when there is a missed call. The silent mode will be disabled for 15 seconds when you transmit, receive or press any other buttons. To turn silent mode ON: 1. MENU/GRP to enter Common Menu. 2. Sele

35、ct “SLNT”. 3. SEL/ to select. 4. to turn Silent Mode ON. “Y” is displayed on the Channel Indicator. appears. 5. to turn Silent Mode OFF. “N” is displayed on the Channel Indicator. disappears. Up Timer Enables your radio to time up to 59 minutes 59 seconds. You can receive incoming calls in this mode

36、. To use up timer: 1. MENU/GRP to enter Common Menu. Advance to “TIME”. 2. SEL/ to select the Up Timer. 3. SEL/ to start the Up Timer. 4. SEL/ to pause the Timer. SEL/ to ON/OFF the Timer. 5. MENU/GRP or PTT to stop or reset up timer. Note: If a call is received, the ID Name will be indicated and th

37、en the radio will return to timer mode and the Call Icon will blink. Key Lock Press and hold SEL/ until /”LOCK” appears to lock the keypad. Press and hold SEL/ until /”UNLK” disappears to unlock the keypad. LCD Backlight The LCD display will automatically illuminate for 10 seconds after any button i

38、s pressed (except for PTT). Monitor Mode Enables you to listen for weak signals on the current channel. To turn the Monitor Mode ON: 1. Press the MON button for brief listening. The icon blinks. 2. Press and hold the MON button for 2 seconds for continuous listening. The icon continues to blink. To

39、turn the Monitor Mode OFF: Press the MON, MENU/GRP or SEL/ button to return to “Normal” mode. The icon stops blinking. Roger Beep Sounds to indicate the end of a PTT or VOX transmission. It can be heard through the speaker when Key Beep is on. It cannot be heard through the speaker if Key Beep is tu

40、rned off. Press and hold the button while turning the radio ON to turn the Roger Beep ON. Repeat the step to turn Roger Beep OFF. LED Torch Your radio has a built-in LED Torch. The LED Torch indicator will remain on until the button is released. English 10 Warranty Information The authorized Motorol

41、a dealer or retailer where you purchased your Motorola two-way radio and/or original accessories will honour a warranty claim and/or provide warranty service. Please return your radio to your dealer or retailer to claim your warranty service. Do not return your radio to Motorola. In order to be elig

42、ible to receive warranty service, you must present your receipt of purchase or a comparable substitute proof of purchase bearing the date of purchase. The two-way radio should also clearly display the serial number. The warranty will not apply if the type or serial numbers on the product have been a

43、ltered, deleted, removed, or made illegible. What Is Not Covered By The Warranty Defects or damage resulting from use of the Product in other than its normal and customary manner or by not following the instructions in this user manual. Defects or damage from misuse, accident or neglect. Defects of

44、damage from improper testing, operation, mainte- nance, adjustment, or any alteration or modification of any kind. Breakage or damage to aerials unless caused directly by defects in material or workmanship. Products disassembled or repaired in such a manner as to adversely affect performance or prev

45、ent adequate inspec- tion and testing to verify any warranty claim. Defects or damage due to range. Defects or damage due to moisture, liquid or spills. All plastic surfaces and all other externally exposed parts that are scratched or damaged due to normal use. Products rented on a temporary basis.

46、Periodic maintenance and repair or replacement of parts due to normal usage, wear and tear. Copyright Information The Motorola products described in this manual may include copyrighted Motorola programs, stored semiconductor memories or other media. Laws in the United States and other countries pres

47、erve for Motorola, certain exclusive rights for copyrighted computer programs, including the exclusive right to copy or reproduce in any form, the copyrighted Motorola programs. Accordingly, any copyrighted Motorola computer programs contained in the Motorola products described in this manual may no

48、t be copied or reproduced in any manner without express written permission of Motorola. Furthermore, the purchase of Motorola products shall not be deemed to grant either directly or by implication, estoppel, or otherwise, any license under the copyrights, patents or patent applications of Motorola,

49、 except for the normal non-exclusive royalty free license to use that arises by operation of law in the sale of a product. MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M logo are trademarks or registered trademarks of Motorola Trademark Holdings, LLC and are used under license. All other trademarks are the property of their respective owners. 2012 Motorola Solutions, Inc. All rights reserved 1 Deutsch PRODUKTSICHERHEIT UND FUNKFREQUENZSTRAHLUNG FR TRAGBARE ZWEIWEGEFUNKGERTE ACHTUNG! Lesen Sie vor Verwendung des Produkts die HF-Energie- Vorsichtsinformationen und