Icom_IC-F1610_IC-F2610_user_1998.pdf

《Icom_IC-F1610_IC-F2610_user_1998.pdf》由会员分享，可在线阅读，更多相关《Icom_IC-F1610_IC-F2610_user_1998.pdf（23页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL iF1610 VHF TRANSCEIVER iF2610 UHF TRANSCEIVER IC-F1610_F2610.qxd 03.3.7 16:29 Page A (1,1) ii IMPORTANT READ ALL INSTRUCTIONS carefully and com- pletely before using the transceiver. SAVE THIS INSTRUCTION MANUALThis in- struction manual contains important operating instructions fo

2、r the IC-F1610 VHF TRANSCEIVER or IC-F2610 UHF TRANSCEIVER. EXPLICIT DEFINITIONS Versions of the transceiver which display the “CE” on the se- rial number seal, comply with the essential requirements of the 89/336/EEC directive for Electromagnetic Compatibility. RWARNING! NEVER connect the transceiv

3、er to an AC outlet. This may pose a fi re hazard or result in an electric shock. NEVER connect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruin the transceiver. NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect c

4、onnection is made after cutting, the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. Place unit in a secure place to avoid inadvertent use by chil- dren. NEVER expose the transceiver to rain, snow

5、or any liquids. USE supplied microphones only. Other microphones have different pin assignments and may damage the transceiver. SmarTrunk II is a trademark of SmarTrunk Systems, Inc. CAUTIONS WORDDEFINITION RWARNING Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage m

6、ay occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fi re or electric shock. IC-F1610_F2610.qxd 03.3.7 16:29 Page ii (1,1) DO NOT connect the transceiver to a power source using reverse polarity. This connection will not only blow fuses but also may damage the transceiver.

7、 DO NOT use or place the transceiver in areas with tem- peratures below 20C or above +55C or, in areas subject to direct sunlight, such as the dashboard. AVOIDoperating the transceiver without running the vehi- cles engine. The vehicles battery will quickly run out if the transceiver is in transmiss

8、ion while the vehicles engine is off. AVOIDplacing the transceiver is excessively dusty envi- ronments. AVOIDplacing the transceiver against walls. This will ob- struct heat dissipation. AVOIDthe use of chemical agents such as benzine or al- cohol when cleaning, as they can damage the transceivers s

9、urfaces. BE CAREFUL!The transceiver will become hot when operating continuously for long periods. iii IC-F1610_F2610.qxd 03.3.7 16:29 Page iii (1,1) iv SUPPLIED ACCESSORIES qw r t y u i o!0!1 !2 !3 e LCD-STICKER q Microphone (HM-100) . . . . 1 w Microphone hanger and screw set . . . . . . . . . . .

10、1 set e Microphone cable . . . . . . . 1 r DC power cable (OPC-345) . . . . . . . . . . . . . 1 t Mounting bracket . . . . . . . . 1 y Bracket bolts . . . . . . . . . . . 4 u Mounting screws (M5 12) 4 i Self-tapping screws (M5 20) . . . . . . . . . . . . . . 4 o Flat washers . . . . . . . . . . . 4

11、!0 Spring washers . . . . . . . . . 4 !1 Nuts . . . . . . . . . . . . . . . . . . 4 !2 Fuses (15A) . . . . . . . . . . . . 2 !3 Function name stickers 1 set D Function name stickers Use these to label the programmable function keys (P0 to P4) according to their assigned functions. TABLE OF CONTENTS

12、IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii EXPLICIT DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . ii CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii TABLE OF CONTENTS . . . . . . . . . . . . . . . . .

13、 . . . . . . . . . . iv SUPPLIED ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . iv 1 PANEL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . 16 I Front panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 I Programmable function keys . . . . . . . . . .

14、. . . . . . . . . . 2 I Function display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 I Turning power on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I Channel selection . . . . . . . . . .

15、 . . . . . . . . . . . . . . . . . . . 7 I Receiving and transmitting . . . . . . . . . . . . . . . . . . . . . . 8 3 CONNECTION AND INSTALLATION . . . . . . . . . . . 1013 I Rear panel connections . . . . . . . . . . . . . . . . . . . . . . . 10 I Mounting . . . . . . . . . . . . . . . . . . . . .

16、. . . . . . . . . . . . . 12 I Seaparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 I Optional UT-105 installation . . . . . . . . . . . . . . . . . . . . 13 4 OPTIONAL SmarTrunk II OPERATION . . . . . . . 1416 I SmarTrunk II and conventional modes . . . . . . . . . . 14 I

17、SmarTrunk II operation . . . . . . . . . . . . . . . . . . . . . . 14 5 OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 NOTE: Some versions include the SP-22 EXTERNAL SPEAKER. IC-F1610_F2610.qxd 03.3.7 16:29 Page iv (1,1) 1 1PANEL DESCRIPTION I Front panel 1 P4P3P2

18、P1P0 23 456 789 M 0# LOW VOLUME CONTROLFUNCTION DISPLAY (p. 6)CH UP/DOWN KEYS (p. 2) (programmable) MICROPHONE CONNECTOR POWER SWITCH PROGRAMMABLE FUNCTION KEYS (pgs. 26) KEYPAD IC-F1610_F2610.qxd 03.3.7 16:29 Page 1 (1,1) 2 1PANEL DESCRIPTION VOLUME CONTROL Adjusts the audio output Minimum audio le

19、vel (when setting control maximum counter clock- wise) is pre-programmed. CHANNEL UP/DOWN KEYS /(CH UP/CH DN) Push to select an operating channel. Can be programmed for one of several functions by your dealer. POWER SWITCH Turns the power on and off. The following functions are available at power on

20、 as options: Automatic scan start Password prompt KEYPAD The keypad allows you to enter digits to: Select memory channels Select tone channels Select DTMF codes (during transmit) Set SmarTrunk II codes MICROPHONE CONNECTOR Connects the supplied microphone or optional DTMF micro- phone for SmarTrunk

21、II operation. NEVER connect other microphones. The pin assignments may be different and the transceiver may be damaged. MICROPHONE The supplied microphone has a PTT switch and a cradle. The following functions are available when the microphone is taken off the cradle or put back on hook: Automatic s

22、can start when putting on hook Automatic priority channel selection when taken off hook Set to inaudible (mute condition) when putting on hook Set to audible (unmute condition) when taken off hook I Programmable keys The following functions can be assigned to the programmable function keys. Assigned

23、 function names can be affi xed to the corresponding keys using the supplied stickers*. *Some functions do not have supplied stickers. D Programmable functions with supplied stickers MEMORY CHANNEL KEYS Select a memory channel directly. MR1 MR2 MR3 MR4 IC-F1610_F2610.qxd 03.3.7 16:29 Page 2 (1,1) 3

24、1PANEL DESCRIPTION BANK KEY Selects a memory bank. PRIORITY CHANNEL KEYS Select priority A or priority B channel. SCAN KEYS Start/stop scan A or scan B. SCAN TAG KEY Adds or deletes the selected channel to the scan group. “” appears above the TAG key when the channel belongs to the scan group. MONIT

25、OR KEY Activates one of (or two of) the following functions on each channel independently. Push and hold the key to unmute the channel (audio is emitted; au- dible condition). Push the key to toggle the mute and unmute conditions (toggles au- dible and inaudible). Push the key to mute the channel (s

26、ets to inaudible only). Push the key to unmute the channel (sets to audible only). Push the key after communication is fi nished to send a reset code. NOTE: The unmute condition (audible conditions) may automatically return to the mute condition (inaudible con- dition) after a specifi ed period. PUB

27、LIC ADDRESS KEY When an optional OPC-617 ACC CABLEis installed, the audio output via the cable can be controlled from the transceiver separately from the VOLUME control. This audio output can be used as a public address function when an external audio amplifi er and speaker are connected additionall

28、y. Push this key, then speak into the microphone while pushing the PTT switch. The CH UP/CH DN keys allow you to set the audio output level from minimum to maximum. EXTERNAL SPEAKER KEY When external connections are made for the public address function, the external speaker drive func- tion is also

29、available simultaneously. The received audio can be heard via the external speaker when this key is pushed. This function is useful when you are out of the vehicle. The audio output level is linked to the transceivers volume control. LOCK KEY Electronically locks all programmable keys except BANK PR

30、I A SCN A TAG MONI PRI B SCN B PA SP LOCK IC-F1610_F2610.qxd 03.3.7 16:29 Page 3 (1,1) 4 1PANEL DESCRIPTION the following: CALL (incl. CALA and CAL B), MONI and EMER keys. OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily or per- manently, depending on the pre-setting. Ask you

31、r dealer or system operator for the output power level for each selection. BEEP KEY Push to toggle beep tones on and off. These are the confi rmation beep tones that by default are emitted each time a key is pushed. LIGHT KEY Push to select the keypad and LCD backlighting condition. ON: Turns backli

32、ghting on continously. OFF: Turns backlighting off. AUTO: Turns backlighting on or off depending on the ACC socket pin 1 voltage. ON: low (0 V)OFF: high (12 V) CONTINUOUS TONE CHANNEL ENTRY KEY Push this key, then input a continous tone memory channel number via the keypad to change the tone frequen

33、cy. TALK AROUND KEY Toggles the talk around function on and off. The talk around function equalizes the transmit frequency to the receive frequency for mobile-to-mobile communi- cation. WIDE/NARROW KEY Push W/N to toggle the bandwidth between wide and narrow operation. This function is available for

34、 wide/narrow transceiver versions only. DTMF CHANNEL SELECT KEY Push this key to select a DTMF channel. Push this key, then select the desired DTMF channel using the CH UP/CH DN keys. Push and hold this key to transmit the selected DTMF code. CALL KEYS Transmit a 5-tone call. Call transmission is ne

35、cessary before you call another station, depending on your signalling system. The CALA and/or CAL B keys may be available when your system employs selective Individual/Group calls. Ask your system operator which call is assigned to each key. LOW1 LOW2 BEEP LITE TONE TA W/N DTMF CALL CAL A CAL B IC-F

36、1610_F2610.qxd 03.3.7 16:29 Page 4 (1,1) 5 1PANEL DESCRIPTION EMERGENCY KEY Push and hold the key to transmit an emergency call. If you want to cancel the emergency call, push (or push and hold) the key again before transmitting the call. The emergency call is transmitted one time only or repeatedly

37、 until receiving a control code, depending on the pre-settting. TX CODE KEY Selects a transmit 5-tone code (station code) chan- nel. Push and hold to change the contents of the station code using the CH UP/CH DN keys. Push to select a TX 5-tone code channel using the CH UP/CH DN keys after pushing t

38、his key. ID MEMORY READ KEY Recalls detected ID codes. Push this key, then push CH UP/CH DN for selec- tion. Up to 5 IDs are remembered. Push and hold this key to erase all memorized IDs. OPTION KEY TRUNKING GROUP KEY Push to select a trunking group (when operating in SmarTrunk II mode). D Programma

39、ble functions without supplied stickers TX CODE CHANNEL UP/DOWN KEY Push to select a TX code channel directly. CHANNEL UP/DOWN FUNCTION When a key is assigned this function, push it to increment or decrement the operating channel. CHANNEL SELECT FUNCTION When a key is assigned this function, push it

40、 to increment or decrement the operating channel. BANK UP/DOWN FUNCTION When a key is assigned this function, push it to increment or decrement the selected channel bank. PRIORITY CHANNEL A REWRITE FUNCTION When a key is assigned this function: Push momentarily to select PRIO A channel. Push and hol

41、d to set the current channel to PRIO A. DTMF RE-DIAL FUNCTION When a key is assigned this function, push it to automatically re-dial the most recent (manually transmitted) DTMF code. EMER CODE ID MR OPT GRP IC-F1610_F2610.qxd 03.3.7 16:29 Page 5 (1,1) 6 1PANEL DESCRIPTION TX CODE CHANNEL UP/DOWN FUN

42、CTION When a key is assigned this function, push it to increment or decrement the TX code channel. TURBO SpeeDial A/B/C/D FUNCTIONS During SmarTrunk II operation, when a key is assigned this function, push it to automatically dial a commonly used num- ber with one push. I Function display q TRANSMIT

43、 INDICATOR Appears while transmitting or sending a 5-tone code. w BUSY INDICATOR Appears while the channel is busy. e BELL INDICATOR Appears or fl ashes when the specifi ed 5-tone call is re- ceived. r LOCK INDICATOR Appears when the lock function is activated. t AUDIBLE INDICATOR Appears when the c

44、hannel is in the audible condition (unmute) condition. y LOW POWER INDICATOR Appears when the selected channel is set for low power output. u ACTIVATED KEY INDICATOR Appears or fl ashes to indicate the key directly below it has been activated. i DOT MATRIX INDICATORS These 2 lines of 16 characters e

45、ach display operating in- formation such as the selected channel, frequency, etc. LOW qwerty ui CH09 173.9 W LOW IC-F1610_F2610.qxd 03.3.7 16:29 Page 6 (1,1) 7 2OPERATION I Turning power on Push to turn power on. A power-up alert tone sounds for about 1 sec. and an opening message may appear. If the

46、 transceiver is programmed with a startup password, input the code from the keypad as instructed by your sys- tem operator. When the password prompt does not clear after inputting the code, you may have input the code incorrectly. In such a case, turn power off, then on again. I Channel selection Th

47、e method for selecting channels may differ according to your system. NON-BANK TYPE: Push the CH UP/CH DNkeys to select the desired operat- ing channel, in sequence or; push one of the digit keys on the keypad to select a channel directly. BANK TYPE: Push BK S, then push CH UP/CH DNto select the de-

48、sired bank number; or Push BD UP or BK DN if the transceiver has these keys. Push CH UP/CH DNto select the desired channel in the selected bank. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning sto

49、ps when receiving a call or taking the micro- phone off from the microphone hanger. IC-F1610_F2610.qxd 03.3.7 16:29 Page 7 (1,1) 8 2OPERATION I Receiving and transmitting RECEIVING: Push to turn power ON. Push CH UP/CH DNto select a channel. When receiving a call, adjust the volume to comfortable lis- tening level. TRANSMITTING: Lift the microphone off the microphone hanger. 5-tone mute may be released (the audible condition is selected and “” appears. A priority channel may be selected automatically. Wait for the channel to become c