Icom_IC-F8100_user.pdf

《Icom_IC-F8100_user.pdf》由会员分享，可在线阅读，更多相关《Icom_IC-F8100_user.pdf（72页珍藏版）》请在收音机爱好者资料库上搜索。

1、HF TRANSCEIVER iF8100 INSTRUCTION MANUAL This device complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. i FOREWORD Thank you for purchasing this Icom product. The IC- F8100 HF TRANSCEIVER is designed and built with Icom

2、s state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. We appreciate you making the IC-F8100 your radio of choice, and hope you agree with Icoms philosophy of “technology fi rst.” Many hours of research and develop- me

3、nt went into the design of your IC-F8100. D FEATURES ALE (Automatic Link Establishment)/Sel- call capability Digital Signal Processor (DSP) allows fl ex- ible fi lter selection Full-dot matrix LCD for a variety of infor- mation IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to op

4、erate the transceiver. SAVE THIS INSTRUCTION MANUAL. This manual contains important safety and operating in- structions for the IC-F8100. EXPLICIT DEFINITIONS WORDDEFINITION R DANGER! Personal death, serious injury or an explosion may occur. R WARNING! Personal injury, fire hazard or electric shock

5、may occur. CAUTIONEquipment damage may occur. NOTE Recommended for optimum use. No risk of personal injury, fire or electric shock. Versions of the IC-F8100 which display the “N33” symbol on the serial number seal, comply with Standard Australia Specifi cation No. AS/NZS 4770: 2000. FOREWORD .i IMPO

6、RTANT .i EXPLICIT DEFINITIONS .i TABLE OF CONTENTS .i PRECAUTIONS .ii FCC INFORMATION .iii SAFETY TRAINING INFORMATION .iii INFORMATION EN MATIRE DE SCURIT .iv 1 PANEL DESCRIPTION .17 Controller (Front panel or HM-192) .1 Rear panel .4 LCD screen .5 AD-119 Optional Junction Box .7 2 BASIC OPERATION

7、.811 Power ON .8 Selecting display mode .8 Selecting a channel .8 Setting audio volume .9 Squelch function .9 Scan function .9 Mode selection.10 Key Lock function .10 VFO operation .11 3 RECEIVE AND TRANSMIT .1218 Basic voice transmit/receive .12 Functions for transmit .13 Functions for receive.15 4

8、 SELCALL/ALE OPERATION .1933 Selcall/ALE .19 5 MENU SCREEN .3446 Edit Menu .34 User Menu .35 Admin Menu .38 CPU Reset .46 6 CONNECTION AND INSTALLATION .4760 Supplied accessories .47 Connections .49 Ground connection .51 Power source .51 Antenna .52 CFU-F8100 (Optional Cooling Fan) .52 RMK-6 (Option

9、al Separation kit) .53 HM-192 (Optional Remote control microphone) .55 Mounting .56 Fuse replacement .58 Connector information for AD-119 .59 7 SPECIFICATIONS .61 8 OPTIONS .62 TABLE OF CONTENTS Icom, Icom Inc. and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the Un

10、ited States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. ii PRECAUTIONS R DANGER HIGH RF VOLTAGE! NEVER attach an antenna or internal antenna connector during trans- missi

11、on. This may result in an electrical shock or burn. R WARNING! NEVER operate the transceiver with a headset or other audio accessories at high volume levels. Hearing experts advise against continuous high volume operation. If you experience a ringing in your ears, reduce the volume or discontinue us

12、e. R WARNING! NEVER operate or touch the trans- ceiver with wet hands. This may result in an electric shock or damage to the transceiver. R WARNING! NEVER apply AC power to the DC13.8V socket on the transceiver rear panel. This could cause a fire or damage the transceiver. R WARNING! NEVER apply mor

13、e than 16 V DC to the DC13.8V socket on the transceiver rear panel, or use reverse polarity. This could cause a fire or damage the transceiver. R WARNING! NEVER let metal, wire or other objects protrude into the transceiver or into connectors on the rear panel. This may result in an electric shock.

14、R WARNING! ALWAYS use the supplied Black and red cables with fuse holders. After connecting the fuse holders, NEVER cut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. R WARNING! Immediately turn OFF the tran

15、sceiver power and remove the power cable if it emits an abnor- mal odor, sound or smoke. Contact your Icom dealer or distributor for advice. CAUTION: NEVER change the internal settings of the transceiver. This may reduce transceiver performance and/or damage to the transceiver. In particular, incorr

16、ect settings for transmitter circuits, such as output power, idling current, and so on, might damage the expensive final devices. The transceiver warranty does not cover any problems caused by unauthorized internal adjustment. CAUTION: NEVER install the transceiver in a place without adequate ventil

17、ation. Heat dissipation may be reduced, and the transceiver may be damaged. DO NOT use or place the transceiver in direct sunlight or in areas with temperatures below 30C (22F) or above +60C (+140F). The basic operations, transmission and reception of the transceiver are guaranteed within the specif

18、ied operat- ing temperature range. However, the LCD display may not be operate correctly, or show an indication in the case of long hours of operation, or after being placed in extremely cold areas. DO NOT use harsh solvents such as benzine or alco- hol when cleaning, as they will damage the transce

19、iver surfaces. DO NOT push the PTT switch when you dont actually desire to transmit. DO NOT place the transceiver against walls or putting anything on top of the transceiver. This may overheat the transceiver. Always place unit in a secure place to avoid inadvertent use by children. BE CAREFUL! If y

20、ou use a linear amplifier, set the transceivers RF output power to less than the linear amplifiers maximum input level, otherwise, the linear amplifier will be damaged. BE CAREFUL! The transceiver will become hot when operating the transceiver continuously for long periods of time. USE only the spec

21、ified microphone. Other manufactur- ers microphones have different pin assignments, and connection to the IC-F8100 may damage the transceiver or microphone. During mobile operation, NEVER place the transceiver where air bag deployment may be obstructed. During mobile operation, DO NOT place the tran

22、sceiver where hot or cold air blows directly onto it. During mobile operation, DO NOT operate the trans- ceiver without running the vehicles engine. When the transceivers power is ON and your vehicles engine is OFF, the vehicles battery will soon become exhausted. Make sure the transceiver power is

23、OFF before starting the vehicle engine. This will avoid possible damage to the transceiver by ignition voltage spikes. During maritime mobile operation, keep the trans- ceiver and microphone as far away as possible from the magnetic navigation compass to prevent erroneous indi- cations. Turn OFF the

24、 transceivers power and/or disconnect the DC power cable when you will not use the transceiver for long period of time. KEEP the transceiver away from the heavy rain, and Never immerse it in the water. The transceiver meets IP54* requirements for dust-protection and splash resis- tance. However, onc

25、e the transceiver has been dropped, dust- protection and splash resistance cannot be guaranteed due to the fact that the transceiver may be cracked, or the waterproof seal damaged, and so on. * Only when the supplied microphone is attached. 1 2 3 4 5 6 7 8 iii SAFETY TRAINING INFORMATION WARNING You

26、r Icom radio generates RF electromag- netic energy during transmit mode. This radio is designed for and classifi ed as “Oc- cupational Use Only”, meaning it must be used only during the course of employment by individuals aware of the hazards, and the ways to minimize such hazards. This radio is NOT

27、 intended for use by the “General Population” in an uncontrolled en- vironment. ForcompliancewithFCCandIndustryCanadaRF Exposure Requirements, the transmitter antenna in- stallation shall comply with the following two condi- tions: 1. The transmitter antenna gain shall not exceed 0 dBi. 2. The anten

28、na is required to be located outside of a vehicle and kept at a distance of 80 centime- ters or more between the transmitting antenna of this device and any persons during operation. For small vehicle as worst case, the antenna shall be located on the roof top at any place on the centre line along t

29、he vehicle in order to achieve 80 cen- timeters separation distance. In order to ensure this distance is met, the installation of the antenna must be mounted at least 80 centimeters away from the nearest edge of the vehicle in order to protect against exposure to bystanders. 3. Transmit only when pe

30、ople outside the vehicle are at least the recommended minimum distance of 160 centimeters away from the properly installed antenna. This separation distance will ensure that there is suffi cient distance from a properly installed externally-mounted antenna to satisfy the RF expo- sure requirements i

31、n the applicable RF exposure compliance standards. CAUTION To ensure that your exposure to RF electromagnetic energy is within the FCC allowable limits for occupational use, always adhere to the following guidelines: DO NOT operate the radio without a proper antenna attached, as this may damage the

32、radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or an antenna specifi cally autho- rized by the manufacturer for use with this radio. DO NOT transmit for more than 50% of total radio use time (“50% duty cycle

33、”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmit- ting when the “TX” icon is displayed. You can cause the radio to transmit by pressing the “PTT” switch. Electromagnetic Interference/Compatibility During transmissions,

34、 your Icom radio generates RF energy that can possibly cause interference with other devices or systems. To avoid such interference, turn OFF the radio in areas where signs are posted to do so. DO NOT operate the transmitter in areas that are sensitive to electromagnetic radiation such as hospi- tal

35、s, aircraft, and blasting sites. FCC INFORMATION FORCLASSAUNINTENTIONALRADIATORS: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer

36、ence when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a r

37、esidential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. CAUTION: Changes or modifi cations to this trans- ceiver, not expressly approved by Icom Inc., could void your authority to operate this transceiver under F

38、CC regulations. iv INFORMATION EN MATIRE DE SCURIT AVERTISSEMENT Votre radio Icom produit une nergie lectromagntique de radiofrquen- ces (RF), en mode de transmission. Cette radio est conue pour un usage professionnel seulement et classe comme tel, ce qui signifi e quelle doit tre utilise uniquement

39、 dans le cadre dun travail par des personnes conscientes des dangers et des mesures visant minimiser ces dangers. Elle NEST PAS conue pour une utilisation grand public, dans un environnement non contrl. AfindesatisfaireauxexigencesdelaFCCetdIn- dustrie Canada en matire dexposition aux RF, il est nce

40、ssaire que lantenne soit installe confor- mment aux trois conditions suivantes: 1. Le gain de lantenne du radio metteur ne doit pas dpasser 0dBi. 2. Il faut que lantenne mettrice de cet appareil soit place lextrieur dun vhicule et tenue loigne dau moins 80 centimtres de toute per- sonne pendant le f

41、onctionnement. Dans le pire des cas, pour un petit vhicule, lantenne doit tre place sur le toit, nimporte o dans laxe central du vhicule, afi n de respecter une distance de 80 cm du bord le plus rapproch du vhicule et ainsi viter que les personnes prsentes soient expo- ses. 3. mettre uniquement lors

42、que les personnes lextrieur du vhicule se trouvent au moins la distance minimale recommande de 160 cm de lantenne correctement installe. Cette distance de scurit assurera que les personnes soient places suffi samment loin dune antenne correcte- ment fi xe lextrieur pour satisfaire aux exigen- ces en

43、 matire dexposition aux RF, en vertu des normes de conformit applicables. MISE EN GARDE Afi n de vous assurer que votre expo- sition une nergie lectromagnti- que de RF se situe dans les limites permises par la FCC pour une utili- sation grand public, veuillez en tout temps respecter les directives sui- van