Icom_IC-F111S_IC-F121S_IC-F211S_IC-F221S_user.pdf

《Icom_IC-F111S_IC-F121S_IC-F211S_IC-F221S_user.pdf》由会员分享，可在线阅读，更多相关《Icom_IC-F111S_IC-F121S_IC-F211S_IC-F221S_user.pdf（20页珍藏版）》请在收音机爱好者资料库上搜索。

1、iF111S VHF TRANSCEIVER INSTRUCTION MANUAL UHF TRANSCEIVER iF121S iF211S iF221S IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page a (1,1) i IMPORTANT EXPLICIT DEFINITIONS RWARNING! NEVERconnect the transceiver to an AC outlet. This may pose a fi re hazard or result in an electric shock. CAUTION! NEVER

2、touch the transceiver (especially the heat sink) when transmitting continuously for long peri- ods. It will become hot. NEVERconnect the transceiver to a power source of more than 16 V DC such as a 24 V battery. This connection will ruin the transceiver. NEVERcut the DC power cable between the DC pl

3、ug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be damaged. NEVERplace the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. NEVERallow children to touch the transceiver. NEVERexpose the transceiver to

4、 rain, snow or any liquids. PRECAUTION WORDDEFINITION RWARNING Personal injury, fi re hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fi re or electric shock. READ ALL INSTRUCTIONScarefully and com- pletely

5、before using the transceiver. SAVE THIS INSTRUCTION MANUALThis instruction manual contains important operating instructions for the IC-F111S/F121S VHF TRANSCEIVER and IC- F211S/F221S UHF TRANSCEIVER. Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United st

6、ates, the United Kingdom, Germany, France, Spain, Russia and/or other coun- tries. SmarTrunk II is a Trademark of SmarTrunk Systems, Inc. IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page i (1,1) ii USEthe supplied microphone only. Other microphones have different pin assignments and may damage the t

7、rans- ceiver. DO NOTuse or place the transceiver in areas with tempera- tures below 22F (30C) or above +140F (+60C), or in areas subject to direct sunlight, such as the dashboard of a vehicle. AVOIDoperating the transceiver without running the vehi- cles engine. The vehicles battery will quickly run

8、 out if the transceiver is in transmission while the vehicles engine OFF. AVOIDplacing the transceiver in excessively dusty envi- ronments. AVOIDplacing the transceiver against walls. This will obstruct heat dissipation. AVOIDthe use of chemical agents such as benzine or alco- hol when cleaning, as

9、they damage the transceiver surfaces. For U.S.A. only CAUTION: Changes or modifications to this transceiver, not ex- pressly approved by Icom Inc., could void your authority to operate this transceiver under FCC regulations. TABLE OF CONTENTS IMPORTANT . i EXPLICIT DEFINITIONS . i PRECAUTION . i TAB

10、LE OF CONTENTS . ii 1 PANEL DESCRIPTION . 15 I Front panel . 1 I Function LED . 2 I Programmable function keys . 3 2 OPERATION . 68 I Turning power ON . 6 I Channel selection . 6 I Receiving and transmitting . 7 DTransmitting notes . 7 DScrambler function . 8 DUser set mode . 8 3 CONNECTION AND MAIN

11、TENANCE . 913 I Rear panel and connection . 9 I Supplied Accessories . 10 I Mounting the transceiver. 11 I Optional UT-108 installation . 11 I Optional UT-109/UT-110 installation . 12 I Optional OPC-617 installation. 12 I Antenna. 13 I Fuse replacement . 13 I Cleaning . 13 4 OPTIONS . 14 5 SAFETY TR

12、AINING INFORMATION . 15 IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page ii (1,1) 1 1PANEL DESCRIPTION TX/RX 1234 q wer Function LED (p. 2) IFront panel qAF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. Minimum audio level is pre-programmed. wMICROPHONE CONNECTOR Connect the

13、supplied microphone or optional DTMF micro- phone. NEVER connect non-specified microphones. The pin assignments may be different and the transceiver may be damaged. eDEALER-PROGRAMMABLE KEYS P0 to P3 Desired functions can be programmed independently by your Dealer. rPOWER SWITCH POWER Push to turn t

14、he power ON and OFF. The following functions are available at power ON as options: -Automatic scan start -Password prompt -Set mode IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page 1 (1,1) 2 1PANEL DESCRIPTION IFunction LED qCHANNEL INDICATORS Indicates the operating channel. Blinks when receiving a

15、 signal during scanning opera- tion. All LEDs blink while entering the power ON password. wTX/RX INDICATOR Lights red: while transmitting Lights green: while the channel is busy Blinks orange (green and red blink simultaneously): when the specifi ed 2-tone, 5-tone call is received. Green and red bli

16、nk alternately: cloning error eACTIVATED KEY INDICATOR (LP 0/1/2) Appears when a pre-programmed key function is acti- vated. NOTE: When all function LEDs blink, check the DC battery voltage is not too high. DD MICROPHONE The supplied microphone has a PTT switch and a hanger hook. The following funct

17、ions are available when the microphone is on or off hook: -Automatic scan start when hook on. - Automatic priority channel selection when hook off. - Sets to Inaudible condition (mute condition) when hook on. - Sets to Audible condition (unmute condition) when hook off. 1234 TX/RX q we IC-F111S_F121

18、S_F211S_F221S 02.10.3 11:54 AM Page 2 (1,1) 3 1PANEL DESCRIPTION IProgrammable function keys The following functions can be assigned to P0, P1, P2 and P3 programmable function keys. Consult your Icom Dealer or System operator for details con- cerning your transceivers programming. In the following e

19、xplanations, programmable function names are bracketed. The specifi c switch used to activate the func- tion depends on programming. CH UP AND DOWN KEYS Select an operating channel. BANK KEY Select and determine a bank number. SCAN START/STOP KEY Push this key to start scanning; and push again to st

20、op. NOTE: Place the microphone on hook to start scanning. Take the microphone off hook to stop scanning. CH UP CH DN BANK SCAN TAG KEY Adds or deletes the selected channel to the scan group. PRIORITY CHANNEL KEYS Push these keys to select priority A or priority B channel, respectively. OPERATING CHA

21、NNEL KEYS Select an operating channel directly. LOCK KEY Push this key for 1 sec. to lock all programmable keys except the following: CALL (incl. CAL A and CAL B), MONI and EMER keys. PRI A PRI B CH1 CH2 CH3 CH4 TAG SCAN A SCAN B LOCK IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page 3 (1,1) 4 1PANEL

22、 DESCRIPTION TALK AROUND KEY Turns the talk around function ON and OFF. The talk around function equalizes the transmit frequency to the receive frequency for mobile-to- mobile communication. WIDE/NARROW KEY Push this key to toggle the bandwidth between wide or narrow. DTMF AUTODIAL KEY Push this ke

23、y to transmit a specifi ed DTMF code. CALL KEY Transmit a 2-tone, 5-tone code. Call transmission is necessary before you call another station depending on your signaling sys- tem. The CAL A and/or CAL B keys may be avail- able when your system employs selective Individual/Group calls. Ask your Deale

24、r which call is assigned to each key. MONITOR KEY Activates one of (or two of) the following functions on each channel independently: Push and hold the key to unmute the channel (audio is emitted; Audible condition). Push the key to toggle the mute and unmute condi- tions (toggles Audible and Inaudi

25、ble). Push the key to mute the channel (sets to Inaudible only). Push the key to unmute the channel (sets to Audible only). Push the key after communication is fi nished to send a reset code. NOTE: The unmute condition (Audible condi- tion) may automatically return to the mute con- dition (Inaudible

26、 condition) after a specified period depending on the pre-setting. OUTPUT POWER SELECTION KEYS Select the transmit output power temporarily, or permanently, depending on the pre-setting. Ask your Dealer or System Operator for the out- put power level for each selection. MONITA W/N DTMF H/L CALL CAL

27、A CAL B IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page 4 (1,1) 5 1PANEL DESCRIPTION EMERGENCY KEY Push and hold the key to transmit an emergency call. If you want to cancel the emergency call, push and hold (or push) the key again before trans- mitting the call. Depending on the pre-setting, the e

28、mergency call is transmitted one time only, or repeatedly, until receiving a control code. Hook Scan Several functions are available for the hanger function when taking the microphone from its hanger (hanger-off) and/or returning it to the hanger (hanger-on). USER SET MODE KEY Changes the contents o

29、f the items in the User Set mode. Please refer to p. 8. Push and hold this key for 1 sec. to enter set mode. Push this key again momentarily to select the desired item. Push P2 and P3 to set the desired level/condition. Push and hold this key again to exit set mode. User set mode also available via

30、the Power ON function. SCRAMBLER KEY Push and hold to turn the voice scrambler func- tion ON. Push this key to turn the voice scrambler func- tion OFF. NOTE: The optional UT-109 (#02) or UT-110 (#02) VOICE SCRAMBLER UNIT is required. UT-109: Non-rolling type. 32 codes are available. UT-110: Rolling

31、type. Provides higher communi- cation security. 1020 (4 groups 255) codes are available. This transceiver requires version #02 of these units. Do not install version #01, as they are not compatible. Some PC board modifications are required when installing UT-109 and UT-110. Please refer to Optional

32、UT-109/UT-110 installation. (p.12) Please contact your Dealer for details. EMER SCRM HOOK SET IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page 5 (1,1) 6 2OPERATION ITurning power ON q Push to turn the power ON. w If the transceiver is programmed for a start up passcode, input the digit codes as dire

33、cted by your Dealer. The keys in the table below can be used for password input: The transceiver detects numbers in the same block as identical. Therefore “01234” and “56789” are same. e When all channel indicator LEDs still blink after inputting 4 digits, the input code number is incorrect. Turn th

34、e power off and start over in this case. IChannel selection Several types of channel selection are available. The meth- ods may differ according to your system setup. NON-BANK TYPE: Push CH UP/CH DN to select the desired operating chan- nel, in sequence; or, push one of the CH 1 to CH 4 keys to sele

35、ct a channel directly. BANK-TYPE: Push BANK to toggle between bank 1 and 2. AUTOMATIC SCAN TYPE: Channel setting is not necessary for this type. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call or when taking the microphone off hook. KEY

36、NUMBER 01234 56789 IC-F111S_F121S_F211S_F221S 02.10.3 11:54 AM Page 6 (1,1) 7 2OPERATION IReceiving and transmitting RECEIVING: q Push POWER to turn the power ON. w Push CH UP or CH DN to select a channel. e When receiving a call, adjust the audio output level to a comfortable listening level. TRANS

37、MITTING: r Take the microphone off hook. The channel is busy when TX/RX indicator turns green. - According to the trasceivers setting; 2-tone, 5-tone mute may be released. (The audible condition is selected) A priority channel may be selected automatically. t Wait for the channel to become clear. y

38、Push the CALL key when initiating a call from your side. - According to the trasceivers setting; Coded audio may be heard from the transceiver, then TX/RX indicator turns green. This operation may not be necessary depending on your signal- ing system. Ask your Dealer. u While pushing and holding PTT

39、, speak into the micro- phone at your normal voice level. i Release PTT to receive. IMPORTANT:To maximize the readability of your signal: (1) Pause briefl y after pushing PTT (2) Hold the microphone 2 to 5 cm from your mouth, then speak into the microphone at a normal voice level. DTransmitting note

40、s Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: The channel is in mute condition. Channel is busy. A matched/non-matched CTCSS code is received. The selected channel is a receive only channel. Time-out timer After

41、continuous transmission for a pre-programmed period, the time-out timer is activated causing the transceiver to stop transmitting and automatically select receive. Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. IC-F

42、111S_F121S_F211S_F221S 02.10.3 11:54 AM Page 7 (1,1) 8 2OPERATION DScrambler function The UT-109 (#02) or UT-110 (#02) optional voice scrambler unit provides high performance private communication between stations with the same scrambler codes. q Push and hold SCRM to turn the scrambler function ON.

43、 w Push SCRM to turn the function OFF. DUser set mode User set mode is accessed at power ON and allows you to set seldom-changed settings. In this case you can “cus- tomize” transceiver operation to suit your preferences and operating style. Entering the user set mode: qWhile pushing and holding P1

44、and P2, push POWER to enter user set mode at power ON. wPush and hold P0 to enter user set mode. Push P0 again momentarily to select the item. The channel indicator lights respectively to indicate the function is selected. Available set mode functions; Backlight (lights): OFF, Dim, Auto or ON Beep (lights): OFF or