Motorola_T92-H2O_user.pdf

《Motorola_T92-H2O_user.pdf》由会员分享，可在线阅读，更多相关《Motorola_T92-H2O_user.pdf（178页珍藏版）》请在收音机爱好者资料库上搜索。

1、TLKR T92 H2O OWNERS MANUAL de-DEes-ESfr-FR da-DKsv-SE it-IT nl-NLpt-PT nb-NOtr-TRpl-PLru-RUuk-UA en fi-FI 1 English RF ENERGY EXPOSURE AND PRODUCT SAFETY GUIDE FOR PORTABLE TWO- WAY RADIOS ATTENTION! Before using this product, read the RF Energy Exposure and Product Safety Guide that ships with the

2、radio which contains instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulation. Package Contents 2 x TLKR T92 H20 Radio 2 x Whistle Belt Clip 1 x Car Charger with two USB cable 2 x Rechargeable 800mAh NiMH battery pack TLKR T92 H20 Manual

3、 Frequency Chart Features and Specifications 8 PMR Channels 121 Sub-Codes (38 CTCSS Codes VOX L1, L2, L3 13. Interference Eliminator Code 1121 2 3 4 5 1 6 7 8 9 11 12 13 10 MN002243A01_ac.book Page 3 Friday, March 10, 2017 5:52 PM English 4 Removing the Three AA Alkaline Batteries 1. Make sure your

4、radio is turned OFF. 2. With the back of the radio facing you, loosen the retaining screw on the battery door and open the cover. 3. Gently remove each alkaline battery by easing each battery out individually. 4. Close the battery cover and tighten the retaining screw on the battery door. Note: Exer

5、cise care when removing NiMH or AA batteries. Do not use sharp or conductive tools to remove either of these batteries. Remove the batteries before storing your radio for an extended period of time. Batteries corrode over time and may cause permanent damage to your radio. Radio Battery Meter The Rad

6、io Battery icon shows the battery charge level from full to empty . When the radio has one segment left, the radio chirps periodically or after releasing the PTT button (Low Battery Alert). Battery Capacity Maintenance 1. Charge the NiMH batteries once every three months when not in use. 2. Remove t

7、he battery from the radio after using for storage purposes. 3. Store the NiMH batteries in a temperature between -20 C to 35 C and in low humidity. Avoid damp conditions and corrosive materials. Using the Micro-USB Charger The micro-USB charger is a handy port that allows you to conveniently charge

8、your NiMH battery pack. 1. Make sure your radio is turned OFF 2. Plug the micro-USB cable into the micro-USB charging port on your radio. Connect the other end of the micro-USB charger to wall power outlet. 3. An empty battery will be fully charged in eight hours. 4. The battery meter bar will move

9、when the battery is charging. Note: It is recommended to power OFF your radio while charging. However, if power is ON while charging, you may not be able to transmit a message if the battery is completely empty. Allow time for the battery to charge to one bar before attempting to transmit a message.

10、 When moving between hot and cold temperatures, do not charge the NiMH battery pack until the temperature acclimates (usually about twenty minutes). For optimal battery life, remove the radio from the charger within sixteen hours. Do not store the radio while connected to the charger. Attaching and

11、Removing the Belt Clip 1. Attach the belt clip to the TLKR plate at the back of the radio until the clip clicks in place. 2. Attach the belt clip to pocket or belt strap until the clip clicks in place. To Remove 1. Push the release tab on top of the belt clip to release the latch. 2. Pull the belt c

12、lip away from the back of the radio. Turning your Radio On and Off Press and hold the Power button to turn the radio ON or OFF. 1. In the ON position, the radio chirps and briefly shows all feature icons available on the radio. MN002243A01_ac.book Page 4 Friday, March 10, 2017 5:52 PM 5 English 2. T

13、he display screen then shows the current channel, code and all features that are enabled. Setting the Volume From Standby Mode, press on either or to show the current value. Press or again to adjust the volume setting. 1. Press to increase the speaker volume. 2. Press to decrease the speaker volume.

14、 Do not hold the radio close to your ear. If the volume is set to an uncomfortable level, it could hurt your ear. Adjust 0 to mute the speaker. TALKING AND LISTENING All radios in your group must be set to the same channel and Interference Eliminator Code in order to communicate. 1. Hold your radio

15、58 cm from your mouth. 2. Press and hold the PTT button while speaking. The Transmit icon appears on the display. 3. Release the PTT button. You can now receive incoming calls. When you do, the Receive icon appears on the display. For maximum clarity, hold the radio 2 to 3 inches away and avoid cove

16、ring the microphone while talking. Talk Range Your radio is designed to maximize performance and improve transmission range. Do not use the radios closer than 5 feet apart. Monitor Button Pressing and holding Scan/Monitor button 3 seconds allows you to listen to the volume level of the radio when yo

17、u are not receiving. This allows you to adjust the volume, if necessary. You can also press Scan/Monitor button to check the activity on your current channel before you talk. Push-to-Talk Time-out Timer To prevent accidental transmissions and save battery life, the radio emits a continuous warning t

18、one and stops transmitting if you press the PTT button for 60 seconds continuously. MN002243A01_ac.book Page 5 Friday, March 10, 2017 5:52 PM English 6 MENU OPTIONS Selecting the Channel Your radio has eight channels. The channel is the frequency the radio uses to transmit. 1. With the radio ON, pre

19、ss Menu button until the channel number starts to flash. 2. Press or to change the channel. Long press on these keys allows you to scroll through the channels rapidly to browse the codes. 3. Press PTT button to exit menu or Menu button to continue set up. Selecting the Interference Eliminator Code I

20、nterference Eliminator Codes help minimize interference by blocking transmissions from unknown sources. Your radio has 121 Interference Eliminator Codes. To set the code for a channel: 1. Press Menu button twice until the code “9” starts to flash. 2. Press or to select the code. You can press or hol

21、d to speed up scrolling through the codes. 3. Press the PTT button to exit menu or Menu button to continue set up. Setting and Transmitting Call Tones Your radio can transmit different call tones to other radios in your group so you can alert them that you want to talk. Your radio has 20 call tones

22、for you to choose from. To set a call tone: 1. Press Menu button three times until Call Tone icon appears. The current call tone setting will flash. 2. Press or to change and listen to the call tone. Menu Key Menu Key Menu Key Menu Key Menu Key Menu Key Menu Key Menu Key Menu Key Menu Key Two Way Mo

23、de Channel (1-8) Sub Code (0-121) Call Tone (1-20) Vibrate Alert (On/Off) Keypad Tones (On/Off) Talk Confirmation Tones (On/Off) Dual Watch Channel (1-22) Dual Watch Interference Eliminator Code Voice Operated Transmission (VOX) (Off, L1,L2,L3) MN002243A01_ac.book Page 6 Friday, March 10, 2017 5:52

24、PM 7 English 3. Press the PTT button to exit menu or Menu button to continue set up. In order to transmit your call tone to other radios, set up the same channel and Interference Eliminator Code on your radio and press Call Tone button. Voice Operated Transmission () Transmission is initiated by spe

25、aking into the microphone of the radio instead of pushing the PTT button. 1. Press Menu button four times until icon appears on the display. The current setting (L1-L3) will flash. 2. Press or to select the sensitivity level. 3. Press the PTT button to exit menu or Menu button to continue set up. No

26、te: There is a short delay between the time you start talking and when the radio transmits. Dual Channel Monitor Enables you to scan the current channel and another channel alternately. To set another channel and start Dual Channel: 1. Press Menu button five times until the Dual Channel icon appears

27、. The Dual Channel will flash. 2. Press or to select the channel then press Menu button. 3. Press or to select the Interference Eliminator Code. 4. Press the PTT button to exit menu or Menu button to continue set up. 5. The radio starts to Dual Channel. Note: If you set the same channel and code as

28、the current channel, Dual Channel Monitor turns OFF. Silent Mode (Vibrate Alert) Silent Mode (Vibrate Alert) notifies you that your radio is receiving a message. This is useful in noisy environments. When the alert is on, the radio vibrates once every 30 seconds when you receive a message on the cha

29、nnel and code you set. 1. Press Menu button seven times until Vibracall icon is displayed. The current setting will flash. 2. Press or to change the setting to On/Off. 3. Press the PTT button to exit menu or Menu button to continue set up. Keypad Tones You may enable or disable the speaker key tones

30、. You will hear the key tone each time a button is pushed. 1. Press Menu button eight times until Keypad Tone icon appears. The current setting On/Off will flash. L3 = High Sensitivity for quiet environments L2 = Medium Sensitivity for most environments L1 = Low Sensitivity for noisy environments MN

31、002243A01_ac.book Page 7 Friday, March 10, 2017 5:52 PM English 8 2. Press either or to turn On/Off. 3. Press the PTT button to confirm or Menu button to continue set up. Note: The following are not disabled when the key tone feature is OFF: Transmit time-out alert tone Call tone Low battery alert t

32、one or The transmitted talk confirmation tone Transmitting a Talk Confirmation Tone You can set your radio to transmit a unique tone when you finish transmitting. It is like saying “Roger” or “Over” to let others know you have finished talking. 1. Press Menu button nine times until the Roger Tone ic

33、on appears. The current setting On/Off flashes. 2. Press or to turn On or Off. 3. Press the PTT button to set or Menu button to continue set up. Emergency Alert Mode The Emergency Alert feature can be used to signal members in your group of your need for urgent help. T92 H2O radios will operate in a

34、n automatic “hands- free” emergency control mode for a total of 30 seconds after activating the Emergency Alert. T92 H2O radios in your group will automatically advance the speaker volume to the maximum setting and sound a warbling alert tone for 8 seconds. The alert tone is emitted from your own ra

35、dio speaker and the receiving radios in your group. After the 8 second alert, any spoken words or incidental sounds at your end will be transmitted to the group for 22 seconds. For the 30 second duration of Emergency Alert mode, T92 H2O radio controls and buttons will be locked to maximize reception

36、 of the emergency message. 1. Press and hold the Emergency Alert button for 3 seconds. 2. Release the button and the alert tone begin to sound. At the same time, it activates RED LED flash. There is no need to continue to hold the Emergency Alert button or use PTT for your message to be transmitted.

37、 WARNING: The Emergency Alert feature should only be used in the even of an actual emergency. Motorola Solutions is not responsible if there is no response to the emergency alert from the receiving group. Built-in Flashlight Press the Flashlight button to cycle between OFF, RED Light, WHITE Light an

38、d then back to OFF again. The Flashlight will turn off when you press the Flashlight button if the RED Light is left on for more than 3 seconds. The Flashlight will turn off automatically after 30 minutes of non- activity if the battery level is below 50%. Note: Turn off the flashlight when not in u

39、se to conserve battery power. Keypad Lock To avoid accidentally changing your radio settings: 1. Press and hold Menu button until Key Lock Indicator icon displays. 2. You can turn the radio ON and OFF, adjust the volume, receive, transmit, and monitor channels when in the lock mode. All other functi

40、ons remain locked. 3. Press Menu button and hold until Key Lock Indicator is no longer displayed to unlock the radio. MN002243A01_ac.book Page 8 Friday, March 10, 2017 5:52 PM 9 English Scanning Use the scan function to do the following: Search the eight channels for transmissions from unknown parti

41、es. Find someone in your group who has accidentally changed channels or To quickly find unused channels for your own use. There is a priority feature and two modes of scanning (basic and advanced) to make your search more effective. The “Basic Scan” mode uses the channel and code combinations for ea

42、ch of the eight channels as you have set them (or with the default code value of 1). The “Advance Scan” mode will scan all channels for any and all codes; detect any code in use and use that code value temporary for that channel. Priority is given to the “Home Channel” (i.e. the channel and Interfer

43、ence Eliminator Code your radio is set to when you start the scan). This means the initial channel (and code settings) is scanned more often than the other seven channels and your radio will respond quickly to any activity occurring on the home channel as a priority. To start Basic Scanning: 1. Pres

44、s the key briefly. The Scan icon will appear in the display and the radio will begin to scroll through the channel and code combinations. 2. When the radio detects channel activities matching the channel and code combination, the radio will stop scrolling and you can hear the transmission. 3. Press

45、the PTT button within 5 minutes after the end of the transmission to respond and talk to the person transmitting. 4. The radio will resume scrolling through the channels 5 seconds after the end of any received activity. 5. Press the Scan/Monitor button briefly to stop scanning. To start Advanced Sca

46、nning: To set another channel and start Dual Channel Monitor: 1. Press the Scan/Monitor button briefly. The Scan icon will appear in the display and the radio will begin to scroll through the channels. No Interference Eliminator Codes will filter what is heard. 2. When the radio detects channel acti

47、vities with ANY code (or NO code), it stops scrolling and you can hear the transmission. Any Interference Eliminator Code that may be use by other party will be detected and displayed. 3. When you respond and talk to the person transmitting, press the PTT button within five seconds after the end of

48、the transmission. 4. The radio will resume scrolling through the channels 5 seconds after the end of any received activity. 5. Press the Scan/Monitor button briefly to stop scanning. Scanning Notes: 1. The transmission will be on the “Home Channel” if you press the PTT button while the radio is scro

49、lling through inactive channels. You may press the Scan/Monitor button to stop scanning at any time. 2. You may immediately resume the scan by briefly pressing the or if the radio stops on an undesired transmission. 3. You may temporarily remove that channel from the scan list by pressing and holding or for 3 seconds if the radio stops repeatedly on an undesired transmission. You may remove more than one channel this way. 4. Turn the radio OFF and then turn back ON, or EXIT and re- enter the scanning mode by pressing Scan/Monitor b