Vertex_VX-2200_user.pdf

《Vertex_VX-2200_user.pdf》由会员分享，可在线阅读，更多相关《Vertex_VX-2200_user.pdf（20页珍藏版）》请在收音机爱好者资料库上搜索。

1、VX-2200 SERIES OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. YAESU EUROPE B.V. P.O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Valley Business P

2、ark, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong Unsafe Radiation Distance Congratulations! You now have at your fingertips a valuable communications tool: a VERTEX STAN- DARD two-way r

3、adio! Rugged, reliable and easy to use, your VERTEX STANDARD radio will keep you in constant touch with your colleagues for years to come, with negligible maintenance downtime. Please take a few minutes to read this manual carefully. The information presented here will allow you to derive maximum pe

4、rformance from your radio, in case ques- tions arise later on. Were glad you joined the VERTEX STANDARD team. Call on us anytime, because communications is our business. Let us help you get your message across. NOTICE ! There are no owner-serviceable parts inside the transceiver. All service jobs mu

5、st be referred to an authorized VERTEX STANDARD Service Represen- tative. Consult your Authorized VERTEX STANDARD Dealer for installa- tion of optional accessories. SAFETY/WARNING INFORMATION WARNING - DO NOT operate the VX-2200 radio when any person(s) (by- standers) outside the vehicle are within

6、the distances shown in the chart at the bottom of this section. Safety Training information: Antennas used for this transmitter must not exceed an antenna gain of 0 dBd. The radio must be used in vehicle-mount configurations with a maximum op- erating duty factor not exceeding 50 %, in typical Push-

7、to-Talk configurations. This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure condi- tions of its passengers and bystanders by maintaining the minimum separa- tion distance shown below. Failure to observe t

8、hese restrictions will result in exceeding the FCC RF ex- posure limits. Antenna Installation: For rear deck trunk installation, the antenna must be located at least the fol- lowing distance away from rear-seat passengers in order to comply with the FCC RF exposure requirements. For roof top install

9、ations, the antenna must be placed in the center of the roof. VHF Model 4.6 Feet (1.4 m) UHF Model 3.9 Feet (1.2 m) VX-2200 SERIES OPERATING MANUAL1 INTRODUCTION The VX-2200 Series are full-featured FM transceivers designed for flexible mobile and base station business communications in the VHF or U

10、HF Land Mobile bands. These transceiver are designed for reliable business communications in a wide vari- ety of applications with a wide range of operating capability provided by their lead- ing-edge design. The 128-channel memories can each be programmed with a 8-character channel name. Important

11、channel frequency data is stored in EEPROM and flash memory on the CPU, and is easily programmable by dealers using a personal computer and the VER- TEX STANDARD Programming Cable and CE82 Software. The pages which follow will detail the many advanced features provided on the VX- 2200 Series transce

12、iver. After reading this manual, you may wish to consult with your Network Administrator regarding precise details of the configuration of this equipment for use in your application. For North American Users Regarding 406 MHz Guard Band The U.S. Coast Guard and National Oceanographic and Atmospheric

13、 Admin- istration have requested the cooperation of the U.S. Federal Communications Commission in preserving the integrity of the protected frequency range 406.0 to 406.1 MHz, which is reserved for use by distress beacons. Do not attempt to program this apparatus, under any circumstances, for operat

14、ion in the fre- quency range 406.0 - 406.1 MHz if the apparatus is to be used in or near North America. VX-2200 SERIES OPERATING MANUAL2 CONTROLS the red “TX” indicator will disappear and transmission will cease soon thereafter. To resume trans- mitting, you must release the PTT switch and wait for

15、the “penalty timer” to expire (if you press the PTT switch before this timer expires, the timer restarts, and you will have to wait another “penalty” period) Key Lock In order to prevent accidental frequency change or inadvertent transmission, various aspects of the VX-2200s keys may be locked out.

16、To activate the Locking feature, press and hold in the P1 key while turning the radio on. To disable the Locking feature, repeat this power-on procedure. ADVANCED OPERATION Programmable Function (PF) Buttons The VX-2200 Series includes six Programmable Function (PF) Buttons. The PF button functions

17、can be customized, via programming by your VERTEX STAN- DARD dealer, to meet your communications/network requirements. Some features may require the purchase and installation of optional internal accessories. The pos- sible PF button programming features are illustrated below, and these functions ar

18、e explained on the pages to follow. For further details, contact your VERTEX STAN- DARD dealer. For future reference, check the box next to the function that has been assigned to each PF button on your particular radio, and keep it handy. BASIC OPERATION OF THE TRANSCEIVER VX-2200 SERIES OPERATING M

19、ANUAL7 ?: Requires optional unit PF Button (PRESS KEY/PRESS AND HOLD KEY) Function MONI SQL OFF SQL SET DIMMER Channel Up Channel Down Continuous Ch Up Continuous Ch Down Group Up Group Down SCAN SCAN SET Group SCAN Group SCAN SET DW (Dual Watch) Follow-Me SCAN Follow-Me DW LOW TA (Talk Around) TA S

20、CAN Encryption? Emergency RESET CALL 1 CALL 2 CALL 3 DTMF CODE SET Code Up Code Down Code SET Speed Dial Public Address EXT. ACC1 EXT. ACC2 Direct CH#1 Direct CH#2 AF Min Vr Lone Worker HA (Horn Alert) Key Lock SET P1 / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /

21、/ / P2 / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / P3 / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / P4 / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ? / / / / / / -/- -/- / / / /

22、 / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ? / / / / / / -/- -/- / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / ADVANCED OPERATION VX-2200 SERIES OPERATING MANUAL8 Description of Operating Functions MONITOR (MONI) Press (or press and hold) the assigned programmable

23、 key to cancel CTCSS- and DCS-controlled squelch; the TX/BUSY indicator will glow green SQUELCH (SQL) OFF Press (or press and hold) the assigned programmable key to open the SQL to hear background noise (unmute the audio); the TX/BUSY indicator will blink green. SQUELCH (SQL) SET You can manually ad

24、just the squelch level using this function: ?Press (or press and hold) the assigned programmable key. A tone will sound, and the current squelch will level appears on the display. ?Press the ?/? button to select the desired squelch level. ?Press this key again. A tone will sound, and the display wil

25、l revert to the normal channel indication. DIMMER Press (or press and hold) the assigned programmable key to select the brightness level of the display. Available selections are four levels. CHANNEL UP/DOWN Press (or press and hold) the assigned programmable key (generally the ?/? button) to select

26、a different channel within the current group. CC UP/DOWN (CONTINUOUS CH UP/DOWN) Press and holding in the assigned programmable key causes the radio to begin step- ping (repeatedly) upward or downward through the channels. GROUP UP/DOWN Press (or press and hold) the assigned programmable key to sele

27、ct a different group of channels ADVANCED OPERATION VX-2200 SERIES OPERATING MANUAL9 ADVANCED OPERATION CHANNEL SCAN (SCAN) The Scanning feature is used to monitor multiple channels programmed into the trans- ceiver. While scanning, the transceiver will check each channel for the presence of a signa

28、l, and will stop on a channel if a signal is present. To activate scanning: ?Press (or press and hold) the assigned programmable key to activate scanning on the current group. ?The scanner will search the programmed channels, looking for active ones; it will pause each time it finds a channel on whi

29、ch someone is speaking. ?Press (or press and hold) the assigned programmable key again to disable scan- ning. Operation will revert to the programmed revert channel. Note: Your dealer may have programmed your radio to stay on one of the follow- ing channels: ? Current channel (“Talk Back”) ? “Last B

30、usy” channel ? “Priority” channel ? “Scan Start” channel SCAN SET Press (or press and hold) the assigned programmable key to delete the Current Memory channel from the Scanning. When you delete a Group or channel, “- SKIP -” will appear on the LCD for one second after pressing the assigned programma

31、ble key. To restore a particular channel to your scanning list, press (or press and hold) the as- signed programmable key again; “- STOP-” will appear on the LCD for one second after pressing the assigned programmable key. GROUP SCAN The Scanning feature is used to monitor multiple channels programm

32、ed into the trans- ceiver. While scanning, the transceiver will check each channel of the programmed group for the presence of the signal, and will stop on a channel if a signal is present. Press (or press and hold) the assigned programmable key to activate the scanning on the selected groups. VX-22

33、00 SERIES OPERATING MANUAL10 GROUP SCAN SET You may wish to have the Scanner pass through more than one Group during the scanning process (normally, scanning is performed within the current group only). To include the current Group in the scanning loop, press (or press and hold) the as- signed progr

34、ammable key. To remove a Group from Group Scan, press (or press and hold) the assigned programmable key again. DUAL WATCH (DW) The Dual Watch feature is similar to the SCAN feature, except that only two channels are monitored: ? The current operating channel; and ? The Priority channel. To activate

35、Dual Watch: ?Press (or press and hold) the assigned programmable key. ?The scanner will search the two channels; it will pause each time it finds a channel on which someone is speaking. To stop Dual Watch: ?Press (or press and hold) the assigned programmable key. ?Operation will revert to the “Dual

36、Watch Start” channel. FOLLOW-ME SCAN “Follow-Me” Scan feature checks a User-assigned Priority Channel regularly as you scan the other channels. Thus, if only Channels 1, 3, and 5 (of the 8 available chan- nels) are designated for “Scanning,” the user may nonetheless assign Channel 2 as the “User-ass

37、igned” Priority Channel via the “Follow-Me” feature. To activate “Follow-Me” scanning, first select the channel you want to designate as the “User-Assigned Priority Channel” and press (or press and hold)the assigned programmable key. Then press (or press and hold) the Channel Up/Down key (gen- erall

38、y the ?/? button) to recall to the “Scanning Start” channel which has been programmed by your dealer to activate the scanner. When the scanner stops on an “Active” channel, the User-assigned Priority Channel will automatically be checked every few seconds; if activity is found on the User-assigned P

39、riority Channel, the radio will switch between it and the Dealer-Assigned Priority Channel, if any. ADVANCED OPERATION VX-2200 SERIES OPERATING MANUAL11 FOLLOW-ME DUAL WATCH (DW) To set up a “Dual Watch” frequency pair using the “Follow-Me” feature, select a channel using the Channel Up/Down key (ge

40、nerally the ?/? button). Now press (or press and hold) the assigned programmable key; pressing the assigned program- mable key locks the current channel as the User-assigned Priority Channel. Now press (or press and hold) the Channel Up/Down key to select another channel (not the “Scanning Start” ch

41、annel). Your radio will now switch back-and-forth between the currently-selected channel and the User-assigned Priority Channel. During “Follow-Me” scanning (after you have pressed the key), you can set up the “Dual Watch” feature by pressing (or press and holding) the Channel Up/Down key to another

42、 channel. The radio will then scan back and forth between the original User-assigned Priority Channel and the newly-selected channel. The Priority Channel you have assigned (before pressing the key) will be retained in memory until you change it. LOW POWER (LOW) Press (or press and hold) the assigne

43、d programmable key to set the radios transmit- ter to the “Low Power” mode. Press (or press and hold) the key again to return to “High Power” operation when in difficult terrain. When the radios transmitter is set to “Low Power” mode, the “” icon will be indicated on the display. TALK AROUND (TA) Pr

44、ess (or press and hold) the assigned programmable key to activate the Talk Around feature when you are operating on duplex channel systems (separate receive and transmit frequencies, utilizing a “repeater” station). The Talk Around feature allows you to bypass the repeater station and talk directly

45、to a station that is nearby. This feature has no effect when you are operating on “simplex” channels, where the re- ceive and transmit frequencies are already the same. When the “TA” function is activated, the “” icon will be indicated on the display. Note that your dealer may have mode provision fo

46、r “Talk Around” channels by pro- gramming “repeater” and “Talk Around” frequencies on two adjacent channels. If so, the key may be used for one of the other Pre-Programmed Functions. ADVANCED OPERATION VX-2200 SERIES OPERATING MANUAL12 TA SCAN The “TA SCAN” is one of “DW Scan” between Rx and Tx freq

47、uency. It works the Rx channel as priority channel and the radio will always transmit on the Tx Channel if the PTT is pressed in the TA SCAN mode. Press (or press and hold) the assigned programmable key to activate/deactivate the TA SCAN feature. ENCRYPTION (OPTION) When the Voice Scrambler feature

48、is enabled, press (or press and hold) the assigned programmable key to toggle the voice encryption on and off. When the Voice Scrambler feature is activated, the “” icon will be indicated on the display. EMERGENCY The VX-2200 series include an “Emergency” feature which may be useful if you have some

49、one monitoring on the same frequency as your transceivers channel. Press (or press and hold) the assigned programmable key to initiate an emergency call. For further details contact your VERTEX STANDARD dealer. RESET Press (or press and hold) the assigned programmable key to reset the RFC (Ready for Communication) condition, or to reset the keypad entry condition. CALL 1 TO CALL 3 Press (or press and hold) the assigned programmable key to send a 2-Tone or 5-Tone sequential burst which is pre-defined. DTMF CODE SET Press (or press and ho