Icom_IC-400Pro_user.pdf

《Icom_IC-400Pro_user.pdf》由会员分享，可在线阅读，更多相关《Icom_IC-400Pro_user.pdf（48页珍藏版）》请在收音机爱好者资料库上搜索。

1、i400PRO UHF TRANSCEIVER INSTRUCTION MANUAL !IC-400PRO.qxd 03.6.16 2:27 PM Page a (1,1) i RWARNING! NEVERconnect the transceiver to an AC outlet. This may pose a fi re hazard or result in an electric shock. RWARNING! NEVERoperate the transceiver while driving a vehicle. Safe driving requires your ful

2、l attention anything less may result in an accident. NEVERconnect the transceiver to a power source of more than 16 V DC. This will damage the transceiver. NEVERcut the DC power cable between the DC plug and fuse holder. If an incorrect connection is made after cutting, the transceiver might be dama

3、ged. NEVERplace the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. NEVERallow children to play with any radio equipment containing a transmitter. NEVERexpose the transceiver to rain, snow or any liquids. The transceiver may be damaged. NEVERo

4、perate or touch the transceiver with wet hands. This may result in an electric shock or damage the transceiv- er. PRECAUTION Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United states, the United Kingdom, Germany, France, Spain, Russia and/or other count

5、ries. SmarTrunk II is a trademark of the SmarTrunk Systems, Inc. IMPORTANT EXPLICIT DEFINITIONS WORDDEFINITION RWARNING Personal injury, fi re hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, fi re or electri

6、c shock. READ ALL INSTRUCTIONScarefully and com- pletely before using the transceiver. SAVE THIS INSTRUCTION MANUALThis instruction manual contains important operating instructions for the IC-400PRO UHF TRANSCEIVER. !IC-400PRO.qxd 03.6.16 2:27 PM Page i (1,1) ii DO NOTpush the PTT when not actually

7、desiring to trans- mit. DO NOTuse or place the transceiver in areas with tem- peratures below 10C or above +60C, or in areas subject to direct sunlight, such as the dashboard. AVOIDoperating the transceiver without running the vehi- cles engine. When the transceivers power is ON and your vehicles en

8、gine is OFF, the vehicles battery will soon become exhausted. AVOIDplacing the transceiver in excessively dusty envi- ronments. AVOIDplacing the transceiver against walls. This will obstruct heat dissipation. AVOIDsetting the transceiver in a place without adequate ventilation. Heat dissipation may

9、be affected, and the trans- ceiver may be damaged. AVOIDthe use of chemical agents such as benzine or alcohol when cleaning, as they damage the transceiver sur- faces. USE the specifi ed microphone only (supplied or optional). Other microphones have different pin assignments and may damage the trans

10、ceiver. BE CAREFUL!The transceiver will become hot when operating continuously for long periods. This device complies with Standard Australia Specification No. AS/NZS4365- 1996 and AS4295-1995. !IC-400PRO.qxd 03.6.16 2:27 PM Page ii (1,1) iii TABLE OF CONTENTS IMPORTANT . i EXPLICIT DEFINITIONS . i

11、PRECAUTION . i TABLE OF CONTENTS . iii SUPPLIED ACCESSORIES . iv 1 PANEL DESCRIPTION . 14 I Front panel . 1 I Function display . 4 2 BASIC OPERATION . 56 I Turning power ON . 5 I Channel selection . 5 I Receiving and transmitting . 6 3 REPEATER OPERATION . 7 I Repeater operation.7 I Accessing a repe

12、ater.7 4 SCAN OPERATION . 814 I Scan types.8 I Scanning preparation.9 I Open scan .11 I Group and priority scans .12 I Repeater search scan .13 5 GROUP MODE OPERATION . 1516 I Group mode (CTCSS).15 6 SELCALL OPERATION . 1721 I General.17 I Calling operation .17 I When receiving a call .20 I Setting

13、the silent stand-by condition.21 7 OTHER FUNCTIONS . 2233 I Smart-Ring and ATS (Automatic Transponder System).22 I Voice scrambler function.23 I DTMF transmission .24 I Channel lock function.24 I RX frequency setting.25 I Wide/Narrow function.26 I Set mode.27 8 PROGRAMMABLE FUNCTION KEYS . 3436 9 CO

14、NNECTION AND MAINTENANCE . 3740 I Rear panel and connection . 37 I Mounting the transceiver. 38 I Optional UT-108 installation . 39 I Optional UT-109 or UT-110 installation . 39 I Optional OPC-617 installation. 40 I Antenna. 40 I Fuse replacement . 40 I Cleaning . 40 10 SPECIFICATIONS . 41 11 OPTION

15、S . 42 !IC-400PRO.qxd 03.6.16 2:27 PM Page iii (1,1) iv q Microphone . 1 w Microphone hanger and screw set . 1 set e Microphone hanger cable . 1 r DC power cable (OPC-1194) .1 t Function name stickers* (KEY STICKER) .1 y Mounting bracket . 1 u Bracket bolts . 4 i Mounting screws (M512) . 4 o Self-ta

16、pping screws (M520) . 4 !0 Flat washers . 4 !1 Spring washers . 4 !2 Nuts . 4 *Function name stickers Function of keys can be changed. Stickers are supplied for easy identifi cation. qwe ry u i o !0 !1 !2 t KEY-STICKER ICOM SUPPLIED ACCESSORIES !IC-400PRO.qxd 03.6.16 2:27 PM Page iv (1,1) 1 1PANEL D

17、ESCRIPTION ie qFunction Display (p. 4) w uytr Speaker I Front panel qAF VOLUME CONTROL KNOB Rotate the knob to adjust the audio output level. Minimum audio level is pre-programmed. w/ KEYS* Push to select an operating channel. After pushing O, push to toggle between CB bank and Private bank (user pr

18、ogrammable channels). ePOWER SWITCH Push to turn the power ON and OFF. The Automatic scan start function and the password prompt are available at power ON as optional settings. (The optional CS- 400PRO CLONING SOFTWAREis required.) rO KEY* Push to enter channel bank selection mode. In channel bank s

19、election mode, push / to select the desired channel bank. Push for 1 sec. to toggle Function mode, Set mode or Normal mode. Returns to the Normal mode automatically after 30 sec. when no key operations are performed in Function or Set mode. Normal mode Set modeFunction mode Push O for 1 sec. !IC-400

20、PRO.qxd 03.6.16 2:27 PM Page 1 (1,1) 2 1PANEL DESCRIPTION 1 tDUP KEY* NNNNPush to toggle the transmit frequency mode between duplex and simplex. (CB channel 1 to 8 only) Duplex: The set TX frequency is used for the transmission. Simplex: The set RX frequency is used for the transmis- sion. NNNNPush

21、and hold to set the selected channel to priority or normal. Priority channel is used for both group and priority scans. FFFFPush to toggle the 5tone mute activity between CONT (Continuous Tone) and SGL (Single Tone). CONT: SelCall mute is released. SGL: SelCall mute is activated. In this case, PTT s

22、witch action is inhibited while SelCall mute is activated. ySCN KEY* NNNNPush to start or stop the scan. NNNNPush and hold to enter the scan type selection mode. Push / to select the desired scan type. Push SCN to set the channel as a tag channel. - “S” appears for tag channels. FFFFPush to recall t

23、he received ID code. Push / to select the record. uMONI KEY* NNNNActivates the following functions on each channel independently: Push and hold the key to release the mute to the channel (audio is emitted; Audible condition). - “” appears. During “” appears, push the key to mute the channel (sets to

24、 Inaudible). NOTE: The unmute condition (Audible condition) may automatically return to the mute condition (Inaudible condition) after a specifi ed time period depending on the pre-setting. FFFFPush to transmit the SelCall code on the selected channel. FFFFPush and hold to enter the SelCall code/cod

25、e number selection mode (p. 17). Push / to select the desired code/code number. *Information Up to two desired functions, one each for Normal and Function mode, can be re-assigned to , , O, DUP, SCN and MONI keys with the optional CS- 400PRO CLONING SOFTWARE. (p. 34) The default setting is used in t

26、his instruction manual, for description. NNNN: Stands for Normal mode operation. FFFF: Stands for Function mode operation. !IC-400PRO.qxd 03.6.16 2:27 PM Page 2 (1,1) 3 1PANEL DESCRIPTION Key fl ow chart for the default settingiMICROPHONE CONNECTOR Connect the supplied microphone or optional DTMF mi

27、cro- phone. NEVER connect non-specified microphones. The pin assignments may be different and the transceiver may be damaged. DD MICROPHONE The supplied microphone has a PTT switch and a hanger hook. The following functions are available when the microphone is on or off hook: (The optional CS-400PRO

28、 CLONING SOFTWAREis required.) -Automatic scan start when on hook. -Automatic priority channel selection when off hook. -Sets to Inaudible condition (mute condition) when on hook. -Sets to Audible condition (unmute condition) when off hook. Normal mode Function mode Set mode : Set the desired level/

29、mode. : Change the individual setting. / : Change the common setting. : Push to enter channel bank selection mode. Push for 1 sec. to enter Normal mode. : Turn the function ON and OFF. : CH Up: ID-MR Select : Bank/Func : CONT/SGL : Call : CH Down : CH Up: Scan Start/Stop : Bank/Func : Dup/Pri : Moni

30、(Audi) : CH Down Push O for 1 sec. Push O for 1 sec. Push to turn power ON. !IC-400PRO.qxd 03.6.16 2:27 PM Page 3 (1,1) 4 1PANEL DESCRIPTION 1I Function display qTRANSMIT INDICATOR Appears while transmitting. wBUSY INDICATOR Appears while receiving a signal or when the squelch is open. eSIGNAL STREN

31、GTH METER Indicates relative receive signal strength level. rLOW POWER INDICATOR Appears when low output power is selected. High/Low must be assigned to the desired program- mable key using the optional CS-400PRO CLONING SOFTWAREwhen change the output power. tSQUELCH INDICATOR Appears when the chann

32、el is in Audible condition (SelCall/CTCSS mute is released). yDUPLEX INDICATOR Appears when the duplex operation is selected. uSCRAMBLER INDICATOR Appears when the scrambler function is activated. (Optional UT-109 (#02)/UT-110 (#02) SCRAMBLER UNIT is required.) iSELCALL/5TONE INDICATOR Appears when

33、the specifi ed Selcall/5-tone is received. oSCAN CHANNEL INDICATOR Appears when the selected memory channel is specifi ed as a scan channel. !0 ALPHANUMERIC DISPLAY Displays the operating channel number, channel names, Set mode contents, DTMF numbers, etc. !1 UNDER BAR INDICATOR Shows the channel mu

34、te condition (Inaudible condi- tion) as below. The left under bar blinks in Function mode, and lights in Set mode. Appears in Set mode when the key under the indicator can be activated. During “” appears, the channel is Audible condition even if the channel is in mute condition. The channel is in CT

35、CSS mute condition. The channel is in SelCall mute condition. The channel is in both CTCSS/SelCall mute condition. tq werui !0 oy !1 !IC-400PRO.qxd 03.6.16 2:27 PM Page 4 (1,1) 5 2BASIC OPERATION I Turning power ON Push to turn the power ON. I Channel selection Push / to select the desired operating

36、 channel. While pushing and holding or , the displayed channel changes continuously until channel number “01” appears. When displayed channel stops at channel number “01”, beeps are emitted. DPrivate channel selection q Push O (Bank/Func) to enter the channel bank selection mode. Then select the des

37、ired bank with /. Push O (Bank/Func) again to set the bank. w Push / to select the desired operating channel in sequence. NOTE: The selected channel is retained even when the transceiver is turned off. Push O Push or Push About the password prompt: If the transceiver is programmed for a start up pas

38、scode, enter the specifi ed 4-digit code. (The optional CS-400PRO CLONING SOFTWAREis required.) The keys in the table below can be used for password input: The transceiver detects numbers in the same block as identical. Therefore “01234” and “56789” are the same. When the “PASSWORD” indication does

39、not clear after entering 4 digit code, the enter code number is incorrect. In this case, turn the power off and start over. KEY NUMBER 01234 56789 !IC-400PRO.qxd 03.6.16 2:27 PM Page 5 (1,1) 6 2BASIC OPERATION 2 I Receiving and transmitting RECEIVING: q Push to turn the power ON. w Select the desired operating channel. (p. 5) e While receiving a signal, adjust the audio output level to a comfortable listening level. TRANSMITTING: q While pushing and holding PTT, speak into the micro- phone at your normal voice level. w Release PTT to receive. IMPORTANT!: To maxim