Icom_IC-M710RT_user.pdf

《Icom_IC-M710RT_user.pdf》由会员分享，可在线阅读，更多相关《Icom_IC-M710RT_user.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、INSTRUCTION MANUAL MF/HF MARINE TRANSCEIVER iM710RT IC-M710RT.qxd 02.1.9 9:03 Page A ii IMPORTANT READ THIS INSTRUCTION MANUAL CAREFULLY before attempting to operate the transceiver. SAVE THIS INSTRUCTION MANUALThis manual contains important safety and operating instructions for the IC-M710RT MF/HF

2、MARINE TRANSCEIVER. EXPLICIT DEFINITIONS The explicit definitions described below apply to this instruction manual. NOTE: The IC-M710RTGMDSS version has a high-stability crystal oscillator unit. This unit draws a slight current even when power to the transceiver is OFF. To prevent battery exhaustion

3、 when dock- ing your vessel for extended periods, unplug the DC cable from the DC power receptacle. PRECAUTIONS WORDDEFINITION RWARNING Personal injury, fire hazard or electric shock may occur. CAUTION Equipment damage may occur. NOTE If disregarded, inconvenience only. No risk of personal injury, f

4、i re or electric shock. RWARNING!NEVER connect the transceiver to an AC outlet directly. This may pose a fi re hazard or re- sult in an electric shock. RWARNING!NEVER mount the transceiver over- head. The weight of the transceiver is approximately 8 kg., but its apparent weight will increase several

5、 fold due to wave shocks and vibration. The transceiver must be mounted on a fl at hard surface only. NEVER connect a power source of more than 16 V DC such as a 24 volt battery. This connection will ruin the transceiver. NEVER place the transceiver where normal operation of the ship or vehicle may

6、be hindered or where it could cause bodily injury. Place unit in a secure place to avoid inadvertent use by children. NEVER expose the transceiver to rain, snow or any liquids. There are two types of grounding systems available for the IC-M710RTNegative Ground and Floating GroundNEVER install the ne

7、gative ground type to a plus-grounding ship. Such a connection might blow fuses and is not usable. DO NOT use chemical agents such as benzene or al- cohol when cleaning, as they can damage the trans- ceivers surfaces. In maritime mobile operation, KEEP the transceiver and microphone as far away as p

8、ossible (at least 1 m) from the magnetic navigation compass to prevent er- roneous indications. USE an Icom microphone and/or handset only (sup- plied or optional). Other brands may have different pin assignments and may damage the transceiver. AVOID using or placing the transceiver in areas with te

9、mperatures below 20C (4F) or above +60C (+140F). AVOID connecting the transceiver to a power source using reverse polarity. This connection will not only blow fuses but may also damage the transceiver. AVOID placing the transceiver in excessively dusty en- vironments or in direct sunlight. AVOID pla

10、cing the transceiver against walls or putting anything on top of the transceiver. This will obstruct heat dissipation. IC-M710RT.qxd 02.1.9 9:03 Page ii iii IN CASE OF EMERGENCY (for maritime operation) VERSIONS If your vessel requires assistance, contact other ves- sels and the Coast Guard by sendi

11、ng a distress call on 2182 kHz. Or, transmit your distress call using digital selective calling on 2187.5 kHz. The following versions are available for the IC-M710RT: USING 2182 kHz WITH VOICE Push 2182kHz to select the emergency fre- quency. Push ALARM and TX FREQ for 1 sec. to trans- mit a 2-tone

12、alarm signal for at least 30 sec. The transceiver automatically stops the alarm after 50 sec. Push ALARM to turn the alarm transmission off, then push and hold the PTT switch on the micro- phone and send the following information: 1. “MAYDAY, MAYDAY, MAYDAY.” 2. “THIS IS . . . . . . . . . . . ” (nam

13、e of vessel) 3. “LOCATED AT . . . . . . . ” (vessels position) 4. Give the reason for the distress call. 5. Explain what assistance you need. 6. Give additional information: Vessel type Vessel length Vessel color Number of people onboard. USING DIGITAL SELECTIVE CALLING (Only for GMDSS versions with

14、 an optional GM- 110DSC DSC TERMINAL UNIT) When immediate help is needed Push and hold EMERGENCY on the GM- 110DSC for 5 sec., until the short beeps become one long beep, to send the distress call. After 2182 kHz is automatically selected, transmit the appropriate information as at left using voice.

15、 When a potential problem exists Push SEL on the GM-110DSC, then select “all ships call” with ENT and the DATA SELECTOR. Push and hold CALL on the GM-110DSC for 5 sec., until short beeps become one long beep, to use the “all ships call” function. After the pre-selected frequency is selected, transmi

16、t the appropriate information using voice. DSC equipped ships may monitor your transmission. Version GMDSS Marine General Ground type Negative ground and Floating ground Negative ground and Floating ground Negative ground only Description Corrosion-resistant exterior. High stability crystal and FSK

17、narrow fi lter built-in. Optional DSC terminal unit can be connected. 2182 kHz 2-tone alarm is built-in. 2182 kHz 2-tone alarm is built-in. FSK/CW narrow fi lter is optional. All SSB/FSK ITU channels available. 2182 kHz 2-tone alarm is optional. FSK/CW narrow fi lter is optional. ITU channels are op

18、tional. IC-M710RT.qxd 02.1.9 9:03 Page iii iv TABLE OF CONTENTS IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii EXPLICIT DEFINITIONS . . . . . . . . . . . . . . . . . . . . . ii PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii IN CASE OF EMERGENCY . . .

19、 . . . . . . . . . . . . . . . iii VERSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . iv 1 OPERATING RULES AND GUIDELINES . . . . . . 1 2 PANEL DESCRIPTION . . . . . . . . . . . . . . . . . . 25 I Front panel . . . .

20、 . . . . . . . . . . . . . . . . . . . . . . . . 2 I Main unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 D HM-120 microphone keys . . . . . . . . . . . . . . . . . . . 4 I Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 3 SELECTING A CHANNEL/FREQUENCY . .

21、. . 68 I Selecting a channel . . . . . . . . . . . . . . . . . . . . . 6 D Using the channel selector . . . . . . . . . . . . . . . . . . 6 D Using the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 7 D Scan functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 I Selecting

22、a frequency . . . . . . . . . . . . . . . . . . . . 8 D Using the channel selector . . . . . . . . . . . . . . . . . . 8 D Using the keypad . . . . . . . . . . . . . . . . . . . . . . . . . . 8 4 RECEIVE AND TRANSMIT . . . . . . . . . . . . . . 911 I Basic voice receive and transmit . . . . . . . .

23、. . . 9 I Functions for transmit . . . . . . . . . . . . . . . . . . . . 9 D Transmit frequency check . . . . . . . . . . . . . . . . . . . 9 D Transmit power selection . . . . . . . . . . . . . . . . . . . . 9 I Functions for receive . . . . . . . . . . . . . . . . . . . 10 D Squelch function . . .

24、 . . . . . . . . . . . . . . . . . . . . . . 10 D Noise blanker . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D AGC off function . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D RF gain setting . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 D Clarity control . . . . .

25、. . . . . . . . . . . . . . . . . . . . . . . 10 I CW operation . . . . . . . . . . . . . . . . . . . . . . . . . 11 I FSK operation . . . . . . . . . . . . . . . . . . . . . . . . . 11 I Cross channel operation . . . . . . . . . . . . . . . . . 11 5 USER CHANNEL PROGRAMMING . . . . . . . . . 12 I P

26、rogramming a frequency . . . . . . . . . . . . . . . 12 D Receive frequency . . . . . . . . . . . . . . . . . . . . . . . . 12 D Transmit frequency . . . . . . . . . . . . . . . . . . . . . . . 12 D Channel names . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6 SET MODE . . . . . . . . . . .

27、 . . . . . . . . . . . . . . . 1215 I Set mode operation . . . . . . . . . . . . . . . . . . . . 12 I Set mode contents . . . . . . . . . . . . . . . . . . . . . 12 7 CONNECTIONS AND INSTALLATION . . . . 1625 I Supplied accessories . . . . . . . . . . . . . . . . . . . 16 I Attaching 1 remote contro

28、ller . . . . . . . . . . . . . 16 I Attaching 2 remote controllers . . . . . . . . . . . . 17 D Set ID number . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 D Intercom operation . . . . . . . . . . . . . . . . . . . . . . . . 17 I Attaching 2 remote controllers and a PC . . . . 18 I Notes

29、for remote control . . . . . . . . . . . . . . . . . 18 I Connections on rear panel . . . . . . . . . . . . . . . 19 I Connector information . . . . . . . . . . . . . . . . . . 20 I Ground connection . . . . . . . . . . . . . . . . . . . . . 22 I Power source . . . . . . . . . . . . . . . . . . . .

30、. . . . . 22 I Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 D MN-100/MN-101L . . . . . . . . . . . . . . . . . . . . . . . . 23 D AT-130 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 D Non-Icom tuner . . . . . . . . . . . . . . . . . . . . . . . . . . 2

31、3 I Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 D Mounting location . . . . . . . . . . . . . . . . . . . . . . . . . 24 D Mounting example . . . . . . . . . . . . . . . . . . . . . . . . 24 D Transceiver dimensions . . . . . . . . . . . . . . . . . . . . 24 I Installing in

32、ternal options . . . . . . . . . . . . . . . . 25 D Opening the case . . . . . . . . . . . . . . . . . . . . . . . . . 25 D Installing an optional fi lter and alarm unit . . . . . . 25 I Fuse replacement . . . . . . . . . . . . . . . . . . . . . . 25 8 TROUBLESHOOTING . . . . . . . . . . . . . . . .

33、 . . . . 26 9 SPECIFICATIONS AND OPTIONS . . . . . . . . . . 27 I Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . 27 I Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 IC-M710RT.qxd 02.1.9 9:03 Page iv 1 1OPERATING RULES AND GUIDELINES CALL PROCEDURES Calls mu

34、st be properly identifi ed and time limits must be respected. Give your call sign each time you call another vessel or coast station. If you have no call sign, identify your vessel name and the name of the licensee. Give your call sign at the end of each transmission that lasts more than 3 min. You

35、must break and give your call sign at least once every 15 min. during long ship-to-shore calls. Keep your unanswered calls short, less than 30 sec. Do not repeat a call for 2 min. Unnecessary transmissions are not allowed. PRIORITIES Read all rules and regulations pertaining to priorities and keep a

36、n up-to-date copy handy. Safety and dis- tress calls take priority over all others. False or fraudulent distress calls are prohibited and punishable by law. PRIVACY Information overheard but not intended for you can- not be lawfully used in any way. Indecent or profane language is prohibited. LOGS A

37、ll distress, emergency and safety calls must be recorded in complete detail. Log data activity is usu- ally recorded in 24 hour time. Universal Time (UTC) is frequently used. Adjustments, repairs, channel frequency changes and authorized modifi cations affecting electrical op- eration of the equipme

38、nt must be kept in the main- tenance log; entries must be signed by the authorized licensed technician performing or super- vising the work. RADIO LICENSES (1) SHIP STATION LICENSE You must have a current radio station license before using the transceiver. It is unlawful to operate a ship station wh

39、ich is not licensed. Inquire through your dealer or the appropriate govern- ment agency for a Ship-Radiotelephone license appli- cation. This government-issued license states the call sign which is your crafts identification for radio pur- poses. (2) OPERATORS LICENSE A Restricted Radiotelephone Ope

40、rator Permit is the li- cense most often held by small vessel radio operators when a radio is not required for safety purposes. The Restricted Radiotelephone Operator Permit must be posted or be kept with the operator. Only a licensed radio operator may operate a transceiver. However, non-licensed i

41、ndividuals may talk over a transceiver if a licensed operator starts, supervises, and ends the call, and makes the necessary log en- tries. Keep a copy of the current government rules and reg- ulations handy. IC-M710RT.qxd 02.1.9 9:03 Page 1 2 2PANEL DESCRIPTION I Front panel (controller) q MICROPHO

42、NE CONNECTOR (p. 20) Accepts the supplied microphone or an optional handset. NOTE: No audio is output via the speaker when the microphone or handset is not connected. w POWER SWITCH POWER Turns power on and off. e SPEAKER SWITCH SPEAKER Turns the built-in speaker on and off. “” appears in the displa

43、y while the speaker is turned off. Any external speaker connected to the rear panel is not turned off. r DISPLAY INTENSITY SWITCH DIMMER Toggles the display backlight on and off. While pushing, rotate CHANNEL to adjust the backlighting to one of 4 levels. While pushing, rotate GROUP to adjust the di

44、s- play contrast to one of 10 levels. t VOLUME CONTROL VOLUME Adjusts the audio output level. Audio does not come from the speaker when: A microphone is not connected. The SQL switch is turned on and no signal is being received. y GROUP CHANNEL SELECTOR GROUP Selects groups in 20 channel steps and I

45、TU marine channel groups. NOTE: Some versions have no ITU channels. u ANTENNA TUNE SWITCH TUNE (p. 9) Tunes the connected tuner to the antenna. Activates only when an optional antenna tuner such as Icoms AT-130/E is connected. NOTE: When selecting “automatic tuning” in set mode, pushing this switch

46、is not necessary to tune the antenna. (p. 13) i CHANNEL SELECTOR CHANNEL (p. 6) Selects an operating channel within the selected channel group such as ITU channels. User channels can be selected from 1 to 160 (max.) in sequence regardless of the channel group. Changes the operating frequency* after

47、CE is pushed (while “s” appears). The changed frequency is not programmed in this way. o FUNCTION SWITCH FUNC After pushing, activates the secondary functions of these switches: RESET . . Deactivates external control such as from a DSC terminal unit when con- nected. SQL . . . . . Starts and stops s

48、can (p. 7). SPEAKER Activates intercom function (p. 17). RX . . . . . . Sets RF gain (p. 10). TX . . . . . . Selects transmit power (p. 9). CE . . . . . . Reprograms the channel name (p. 12). NOTE: Function availability depends on version. !0 CLARITY CONTROL CLARITY (p. 10) Shifts the receive freque

49、ncy 150 Hz for clear re- ception of an off frequency signal. TUNE DUPSIMP STANDBY TX RX DSCFSCAN SQLN B AGCAGCAGC A43210 ALM MICROPHONE POWER VOLUME ALARM TX FREQ 2182KHz RESET MODE TUNE MF/HF MARINE TRANSCEIVER AGCSQLFUNC CLARITY N B SPEAKER ALARMTX FREQ+ FOR ALARM TX DIMMER GROUPCHANNEL 123 456 789 CE RXTX 0 CH/FREQ iM710 qwe rtyui!0 !1 o !2!3!4!5!6!7!8!9 IC-M710RT.qxd 02.1.9 9:03 Page 2 3 2PANEL DESCRIPTION !1 KEYPAD Enters the selected channel number (or fre- quency*) for direct channel selection. (p. 7) Stores a receive frequency into a user chan- nel or