Vertex_EVX-5400_user.pdf

《Vertex_EVX-5400_user.pdf》由会员分享，可在线阅读，更多相关《Vertex_EVX-5400_user.pdf（40页珍藏版）》请在收音机爱好者资料库上搜索。

1、programmaBlE FunctIons/FEaturEs 6ProgrammableFunctionKeys 2-ToneEncode/Decode 1 5-ToneEncode/Decode 1 MDC-1200Encode/Decode 1 HornAlert PA(PublicAddress) Scan GroupScan DualWatch FM-Scan(Follow-MeScan) TAScan Encryption 1 Privacy(Basic/Enhanced) 2 VOX TalkAround Emergency LoneWorker TXSaveDisable Di

2、rectChannelEntry 3 CodeUp/Down 1 CodeSet 1 SpeedDial 1 DTMFCodeSet 1,3 IDCheck 1 TXMessage 1 ARTSTM 1 /ARTSIITM ( AutoRangeTranspondSystem) 1:Analogmodeonly 2:Digitalmodeonly 3:RequiresOptionalMH-75A8J EVX-5400 opEratIng manual Unsafe Radiation Distance Congratulations! You now have at your ingertip

3、s a valuable communications tool: a Vertex Stan- dard two-way radio! Rugged, reliable and easy to use, your Vertex Standard radio will keep you in constant touch with your colleagues for years to come, with negli- gible maintenance downtime. Please take a few minutes to read this manual carefully. T

4、he information presented here will allow you to derive maximum performance from your radio. Were glad you joined the Vertex Standard team. Call on us anytime, because com- munications is our business. Let us help you get your message across. Notice ! There are no owner-serviceable parts inside the t

5、ransceiver. All service jobs must be referred to an authorized Vertex Standard Service Representative. Consult your Authorized Vertex Standard dealer for installation of optional accessories. Safety/WarNiNg iNformatioN WARNING - DO NOT operate the EVX-5400 radio when any person(s) (bystanders) outsi

6、de the vehicle are within the distances shown in the chart at the bottom of this section. Safety Training information: Antennas used for this transmitter must not exceed an antenna gain of 0 dBi. The radio must be used in vehicle-mount conigurations with a maxi- mum operating duty cycle not exceedin

7、g 50 %, in typical Push-to-Talk con- igurations. This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure limits of passengers and bystanders by maintaining the minimum separa- tion distance shown below. Failu

8、re to observe these restrictions will result in exceeding the FCC RF exposure limits. Antenna Installation: For rear deck trunk installation, the antenna must be located at least the fol- lowing distance away from rear-seat passengers in order to comply with the FCC RF exposure requirements. For roo

9、f top installations, the antenna must be placed in the center of the roof. VHF ModelUHF Model 2.9 Feet (0.89 m) 2.1 Feet (0.64 m) EVX-5400 OpErating Manual1 IntroductIon The EVX-5400 is a full-featured Digital/Analog transceiver designed for lexible mobile and base station business communications in

10、 the VHF/UHF Land Mobile bands. This transceiver is designed for reliable business communications in a wide variety of applications for a wide range of operating capabilities. The EVX-5400 operates using the TDMA protocol for spectrum and power ef- ficiency resulting in lower total equipment cost co

11、mpared to FDMA. Digital eliminates noise and static from voice transmit to deliver only the intended voice message crisply and clearly. EVX-5400 features the AMBE+2 vocoder for en- hanced voice quality. This transceiver allows up to 512-channel capacity and 32 groups which can each be programmed wit

12、h an 8-character Alpha-Numeric Tag. Important channel fre- quency data is stored in the lash memory, and is easily programmable by a Vertex Standard licensed dealer using a personal computer with Vertex Standard Program- ming equipment: FIF-12 USB Programming Interface, CT-104A (or CT-171) Connectio

13、n Cable with CE142 Software. Or, once a single radio is programmed, cloning cable CT-4 can be used to program additional radios directly. The pages which follow will detail the many advanced features provided by the EVX-5400 Series transceiver. After reading this manual, you may wish to consult with

14、 your Network Administrator regarding precise details of the coniguration of this equipment for use in your application. For North American Users Regarding 406 MHz Guard Band The U.S. Coast Guard and National Oceanographic and Atmospheric Ad- ministration have requested the cooperation of the U.S. F

15、ederal Communi- cations Commission in preserving the integrity of the protected frequency range 406.0 to 406.1 MHz, which is reserved for use by distress beacons. Do not attempt to program this apparatus, under any circumstances, for op- eration in the frequency range 406.0 - 406.1 MHz if the appara

16、tus is to be used in or near North America. EVX-5400 OpErating Manual2 WarnIng! Fcc rF ExposurE rEquIrEmEnts THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERA- TION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT

17、 ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. THE GRANTEE IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFI- CATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. This eq

18、uipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installa- tion. This equipment generates, uses and can radiate radi

19、o frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that inter- ference will not occur in a particular installation. If this equipment does cause harmful interference to radio or

20、 television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter- ference by one or more of the following measures: r Reorient or relocate the receiving antenna. r Increase the separation between the equipment and receiver. r Conn

21、ect the equipment into an outlet on a circuit different from that to which the receiver is connected. r Consult the dealer or an experienced radio/TV technician for help. EVX-5400 OpErating Manual3 WarnIng! Ic rss gEnEral rEquIrEmEnts eNgliSh r This device complies with Industry Canada license-exemp

22、t RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. r Under Industry Canada regulations, this radio transmitter

23、may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more t

24、han that necessary for suc- cessful communication. r Antennas used for this transmitter (identify the device by certiication number, or model number if Category II) must not exceed an antenna gain of 0 dBi. The radio must be used in vehicle-mount conigurations with a maximum op- erating duty cycle n

25、ot exceeding 50 %, in typical Push-to-Talk conigurations. Antenna types having a gain greater than 0 dBi are strictly prohibited for use with this device. freNch r Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise

26、 aux deux conditions suivantes: (1) lappareil ne doit pas produire de brouillage, et (2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. r Conformment la rglementation dIndustrie Canada, le prsent m

27、etteur ra- dio peut fonctionner avec une antenne dun type et dun gain maximal (ou in- frieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la pu

28、issance isotrope rayonne quivalente (p.i.r.e.) ne dpassepas lintensit ncessaire ltablisse- ment dune communication satisfaisante. r Antennes utilises pour cet metteur (identiier le dispositif par son numro de certiication ou son numro de modle sil fait partie du matriel de catgorie II) ne doit pas d

29、passer un gain de lantenne de 0 dBi. La radio doit tre utili- se dans des conigurations de montage en vhicule avec un maximum duti- lisation en fonctionnement nexcdant ne pas 50 %, dans des conigurations typiques de Push-to-Talk. Types dantenne ayant un gain suprieur 0 dBi sont strictement interdits

30、 pour une tilisation avec cet appareil. EVX-5400 OpErating Manual4 controls the red “TX” indicator will disappear and transmission will cease soon thereafter. To resume transmitting, you must release the PTT switch and wait for the “penalty timer” to expire (if you press the PTT switch before this t

31、imer expires, the timer restarts, and you will have to wait another “penalty” period). Key Lock In order to prevent accidental operating function/feature change or inadvertent transmission, various aspects of the front panels keys may be locked out. To activate the Locking feature, press and hold in

32、 the P1 key while turning the radio on. To disable the Locking feature, repeat this power-on procedure. BasIc opEratIon EVX-5400 OpErating Manual9 advancEd opEratIon Programmable Function (PF) Keys The EVX-5400 Series includes six Programmable Function (PF) keys. These PF keys can be customized, via

33、 programming by your Vertex Standard dealer, to meet your communications/network requirements. The possible PF key programming features are illustrated on the next page, and these functions are explained beginning after page 12. For further details, contact your Vertex Standard dealer. In this chapt

34、er, the following icons are used to indicate features supported in either the “Analog” mode or “Digital” mode: : Indicates a “Analog” mode only feature. : Indicates a “Digital” mode only feature. For features that are available in both “Analog” and “Digital” modes, no icon is shown. For future refer

35、ence, check the box next to each function that has been assigned to the PF key on your particular radio and keep it handy. EVX-5400 OpErating Manual10 advancEd opEratIon FunctIon programmaBlE KEy (prEss KEy/prEss allowing you to speak in a low voice (whisper) temporarily. Press again, (or press and

36、hold again), the assigned PF key, the display indicates “WHISP OF” briely, and resume normal micro- phone gain. vox Press, (or press and hold), the assigned PF key, the display indicates “VOX O.N” briely, and activates the VOX function; allowing hands-free, automatic activation of the transmitter, b

37、ased on voice input into the microphone. When the VOX func- tion is activated, a small dot (“.”) will be indicated at the bottom right of the dis- play. You may disable the VOX function temporarily by pressing the PTT switch. Press again, (or press and hold again), the assigned PF key, the display i

38、ndicates “VOX OFF” briely, and resume normal operation. vox sEt You can manually adjust the VOX Gain using this function: r Press, (or press and hold), the assigned PF key. A tone will sound, and the cur- rent VOX Gain level will appear on the display. r Press the / key to select the desired VOX Gai

39、n level. Available selec- tions are “VOXLV 8” to “VOXLV +8”. r Press the P4 key to store the new setting. The display indicates “- SET -” briely, then reverts to the normal channel indication. You may cancel the new setting by pressing the P3 key. In this case, the dis- play indicates “- CANCEL -” b

40、riely. Note: If the optional MH-75A8J 16-Keypad Microphone is used, you may select EVX-5400 OpErating Manual15 the VOX Gain level and set/cancel the setting by the microphones A, B, C, and D key in place of , , P3, and P4 key. vox antI-trIp Press, (or press and hold), the assigned PF key to toggle t

41、he VOX Anti-Trip fea- ture “On” and “Off”. When the VOX Anti-Trip feature is set to “On”, the display indicates “ATRP ON” briely, and the transceiver does not activate the transmitter section from the re- ceiver audio or own beep sound. Press again, (or press and hold again), the assigned PF key, th

42、e display indicates “ATRP OFF” briely, and the VOX Anti-Trip feature is disabled. Horn alErt Press, (or press and hold), the assigned PF key, the display indicates “HA ON” briely, and activates the Horn Alert function. If you receive a call from the base station with the signaling, horn alert will b

43、e activated and your vehicles horn will sound. Press again, (or press and hold again), the assigned PF key, the display indicates “HA OFF” briely, and the Horn Alert function is disabled. pa (puBlIc addrEss) Press, (or press and hold), the assigned PF key to use the transceiver as a PA am- pliier. T

44、he Public Address can be used even while scanning and receiving a call. When the Public Address function is activated, the “PA” indication will be indi- cated on the display. Press again, (or press and hold again), the assigned PF key, the Public Address function is disabled. Ext acc 1 Activates the

45、 output port “1” of the D-Sub 15-pin Accessory Connector when pressing the assigned PF key. Ext acc 2 Press, (or press and hold), the assigned PF key to toggle the output port “2” of the D-Sub 15-pin Accessory Connector “On” and “Off”. advancEd opEratIon EVX-5400 OpErating Manual16 advancEd opEratIo

46、n EmErgEncy The EVX-5400 series includes an “Emergency” feature in either analog or digital modes, which may be useful for alerting another party assistance may be required, when monitoring the same frequency as your transceivers channel. Press and hold the assigned PF key, the “- EMG -” indication

47、will be indicated on the display, and initiate an emergency call on the pre-deined channel. For further details contact your Vertex Standard dealer. To revive the radio from the Emergency mode, just press and hold again the as- signed PF key or turn off the radio. lonE WorKEr Press, (or press and ho

48、ld), the assigned PF key, the display indicates “L-WK ON” briely, and activates the Lone Worker feature. The Lone Worker feature is de- signed to emit an alarm for 30 seconds when the Lone Worker Timer (programmed by your Vertex Standard dealer) has expired. Press again, (or press and hold again), t

49、he assigned PF key, the display indicates “L-WK OFF” briely, and the Lone Worker feature is disabled. If the user does not reset the timer by pressing the PTT switch, the radio switches to Emergency mode. group up/doWn Press, (or press and hold), the assigned PF key to select a different group of chan- nels. A group name will appear briely on the display. cH up/doWn Press, (or press and hold), the assigned PF key (generally the / key) to se- lect a different channel. A channel name will appear briely on the display. spEEd cH up/doWn Press and hold