Philips_FM-1100_FM-1200_FM-1300_user.pdf

《Philips_FM-1100_FM-1200_FM-1300_user.pdf》由会员分享，可在线阅读，更多相关《Philips_FM-1100_FM-1200_FM-1300_user.pdf（11页珍藏版）》请在收音机爱好者资料库上搜索。

1、- 1 - User Manual Philips FM1200 / FM1100 / FM1300 VHF or UHF Personal Mobile Radio Dennis Koller PA4DEN Jan Buiting PE1CSI Philips Mobile Radio Collection July 2001 Contents User Manual.1-6 Appendix A, The FM1200 SB0 PMR with Handsfree Kit.7 Appendix B, FM1200/1300 Equipment Identification Code Sys

2、tem.8 Appendix C, Microphone Socket and Power Connector Pinouts.9 Appendix D, Local and Remote Mounting Options.10 Appendix E, Frequently Asked Questions .11 This document to be printed in colour only - 2 - Keyboard Layout: Main Functions: Key(s): Function: 0 1 2 3 4 5 6 7 8 9 Enter channel, frequen

3、cy or number * Scanning # Reverse shift E Activate tone squelch (CTSS / 5-tone) F Go to Calling Channel G Switch between VFO and Memory H Select second function of next key Second (alternate) function: Key: Function: 1 Adjust transmit power 2 Adjust squelch trip level 3 Select CTCSS tone 4 To MENU 5

4、 To Status Menu 6 Show names with memory channels 8 Select step size * Exclude memory channel from scanning 0 Call # Shift + / / off E Select tone squelch F Clear Priority Channel G Clear memory Channel When the transceiver is switched on, the upper line of the display shows the current channel or t

5、he frequency. If a valid tone code is received, it is displayed in the lower right hand corner of the display. The lower display line shows an S (signal strength) meter in the form of a horizontal bar. This is called the normal state. To activate the second function of a key, press the H key. The te

6、xt Select Function will appear. The second (alternate) function of the next key pressed is activated. Press H again to return to the normal state. - 3 - 1. Select Frequency The transceiver operates in one of three modes. Using the G button you may select between VCO and Memory mode. The third mode i

7、s the Priority Channel which may be switched on and off with the F key. VCO mode In VCO mode any frequency that complies with the selected step size (4) may be entered using the number keys on the keypad. The transceiver automatically rounds off the frequency to a valid entry. For example, of you wa

8、nt to listen at 435.012.500 MHz, at a step size of 12.5 kHz, all you need to do is enter 501: 435.-.- 435.0-.- 435.012.500 If a step size of 25kHz is used, entering 501 will cause the transceiver to round off to 435.000.000. Memory mode Starting from VCO mode up to 100 preset frequencies per bank ma

9、y be stored in memory, see Heading 5. These frequencies may be selected when in Memory mode while it is also possible to assign names to channel frequencies. If no frequency has been assigned to the selected channel the transceiver produces an error beep and ignores the number entered. Priority Chan

10、nel mode Provided a frequency has been assigned to the Priority Channel (see Heading 6), this feature allows you to change to this frequency at the flick of a switch. The Calling Channel may be instantly selected by pressing the F key. 2. Select CTCSS tone It may be undesirable for every transmissio

11、n to be heard on a certain frequency. A system called CTCSS is therefore used to pass only those transmissions containing a sub-audible tone of a specific frequency. In the receiver a CTCSS decoder is used to open the squelch and make the transmission (speech) audible when a valid CTCSS tone is dete

12、cted. The frequency of the CTCSS tone may be selected as follows: Display: - Press H ( Select Function ) - Press 3 ( TX CT: *) The lowest frequency is 67.0 Hz, the highest, 250.3 Hz. The quasi-value None is available to disable CTCSS. Separate CTCSS frequencies may be used for TX and RX 3. Tone sque

13、lch The squelch may be remain closed until a valid ZVEI 5-tone code is received. It is also possible to transmit a ZVEI 5-tone sequence at the start of every transmission. Activate: The tone squelch is activated by pressing the E key. When receiving, the yellow LED lights. When transmitting, the sym

14、bol T appears behind the frequency. Adjust: The code may be set as follows: Display: - Press H ( Select Function ) - Press E ( RX: ) Now set the tone for the squelch. The tone code has to be entered using the number keys. If a number flashes, this indicates a DTMF tone. - Press H ( TX: ) Now set the

15、 tone to be transmitted. 1750 Hz tone burst A tone burst is transmitted by pressing the PTT and Squelch Defeat buttons at the same time. The frequency of the tone burst may be adjusted in the Audio menu. 4. Select Step Size Display: - Press H ( Select Function ) - Press 8 ( Step size: * ) The desire

16、d step size is selected by pressing the 0 and # keys ( or ). Confirm your selection by pressing any other key. 5. Store favourite channels Up to 100 favourite channels per bank may be pre-set in the transceiver. A channel is stored as follows: Display: - Select VCO mode (43*.*.* ) - Enter the desire

17、d frequency and choose SHIFT and/or CTCSS if required - Press H (Select Function ) - Press G (Store in: xx) - Select a number, if number has an arrow in front of it, it has been taken for another frequency. This is replaced. (Store in: ?xx) - Press H - If desired, give the channel a name. (Name: ) S

18、ee Heading 10 for text entry. - Press H again - 4 - See Heading 7 for the name display on/off function. 6. Storing Priority (PR) Channel It is very useful, particularly in mobiles, to have a single button available to retrieve the Priority Channel. The Priority Channel frequency may be programmed as

19、 follows: Display: - Select VCO mode (43*.*.* ) - Enter the desired frequency and set SHIFT and/or CTCSS if required - Press H. ( Select Function ) - Press F. ( Calling Frequency? ) - Press H. - If desired, give the channel a name ( Name: ) See Heading 10 for text entry. - Press H again. ( Processin

20、g ) See Heading 7 for the name display on/off function. 7. Name display on/off Names may be assigned to memory channels. The displaying of the name may be switched on and off, as follows: Display: - Press H (Select Function ) - Press 6 8. Clear memory channel Display: - Select Memory mode (* * ) - S

21、elect the channel to be cleared - Press H ( Select Function ) - Press S ( Clear Channel? ) - Press H ( Processing ) 9. Clear Priority (PR) Channel Display: - Select Prioruty Channel (button F) (A * ) - Press H (Select Function ) - Press F (Clear Calling?) - Press H ( Processing ) 10. Text entry Text

22、 entry using the keys on the keypad is largely similar to the method used on GSM phones. For example, the letters A, B and C are behind the number key 2. The desired letter or character is selected by repeatedly pressing a number key. The B button is used to delete a character. Text beyond the curso

23、r position will shift back, just as with the DEL key when using a word processor. The E button is used to enter a space. All characters behind the keys on the keypad are shown in the table below. The up and down arrow keys C and D may be used to step through a character group. The cursor may be move

24、d by pressing the left and right arrow keys F and G. On completion of text entry, press the H key. 11. Scanning De transceiver is capable of scanning in Memory as well as in VFO mode: To scan all frequencies: - Switch to VFO mode by pressing the G button - Press the * button To scan memory channels:

25、 - Select MEMory mode by pressing the G button - Press the * button Press any key to stop scanning. During scanning the red LED is illuminated. If the transceiver has halted on a certain channel, scanning may be resumed by pressing * again. During scanning indicator F is displayed. 12. Exclude chann

26、els from scanning It is possible to skip certain memory channels while scanning. Display: - Select MEMory mode (* 43* ) - Select the relevant channel - Press H (Select Function ) - Press * Indicator E shows that the channel is skipped during scanning. - 5 - To cancel this setting, perform the same k

27、eypresses in reverse order. The indicator will disappear. 13. Transmitter power Transmitter output power is dependent on: - The value set by the internal software - Antenna matching - Temperature To set transmitter power: Display: - Press H (Select Function ) - Press 1 The transmitter power level ma

28、y be adjusted by pressing keys 0 and # or C and D. Confirm desired level by pressing any other key. 14. Repeater shift setting On the UHF radio, the default value for the repeater shift is 1.6MHz. On VHF, the default value is 600 kHz. The MENU allows any other value to be set up (see Heading 17). To

29、 switch repeater shift on and off: Display: - Press H (Select Function ) - Press # Next there are 3 options: - Shift off (43*.*.* ) - Shift negative (TX frequency 1.6MHz lower) (43*.*.* S) - Shift positive (TX frequency 1.6MHz higher) (43*.*.* +S) 15. Reverse shift Reverse shift is useful for tempor

30、ary listening on the repeater input frequency, and transmitting on the repeater output frequency. Reverse shift may be switched on and off by pressing # only, i.e., without first pressing the H button. With reverse shift enabled, an R is shown on the display instead of S. 16. Squelch (trip) level se

31、tting Display: - Press H (Select Function ) - Press 2 The squelch level is then adjustable using the keys 0 and # or C and D. 17. The MENU For lack of buttons on the FM1200/1100/1300, a number of less frequently used functions have been gathered into a Menu. Once in the menu, you can select between

32、available options by means of the 0 and # keys. Option values may be modified as required by pressing the H button. In that case, the indicator with the H key will be visible. Options requiring a number or text to be set may also be edited using the H key. However, these entries need to be confirmed

33、 by pressing an unused key or the H key. Access the menu as follows: - Press H (Select Function ) - Press 4 (xxxxxxx MENU) To keep the menu reasonably tidy, items have been distributed across submenus. The submenus may be viewed from the main menu by pressing the H button. Like the main menu, submen

34、us are closed by pressing an unused key. Available menu items: Options: - Shift * kHz Define amount of shift for repeaters. Adjust value using number keys. - TX with SQ Possible / Not possible With Not possible selected the transmitter can not be keyed while a signal is received. - Limit TX time * s

35、ec Define maximum duration of transmission. Adjust value with number keys. 0 = none. - Range 430-440 / 300-500 144-146 / 100-200 Select VCO range. (UHF or VHF) - Scan mode Wait for silence / Wait briefly / Scan until busy Indicates transceiver activity while in scanning mode. - Scan mode Carrier / S

36、quelch With Carrier selected, the transceiver evaluates signal strength, this is faster. Squelch is better for weak signals. Audio Submenu! - Microphone Normal / PA The AF input may be sent to the loudspeaker output. - Suppress Tones 500Hz / 1750Hz only / Never - 6 - Suppress beep tones. Indicator C

37、 lights while suppressing. - Beep On / Off Keyboard beep. - Beep Volume: - Volume of keyboard beep. - Roger beep On / Off Transmit a beep on keying off the transmitter. - DTMF tones * ms Define length of DTMF tones. Adjust value with number keys. - ZVEI tones * ms Define length of ZVEI tones used fo

38、r 5-tone calling. Adjust value with number keys. Tone burst * Hz Define audio frequency used for opening repeaters. Callsign generator Submenu! - Callsign generator On / On (hold TX) / Off The transceiver may transmit text in Morse. Hold TX causes the transmitter to remain keyed until the text is fi

39、nished. - After call On / Off Callsign may be transmitted immediately after 5- tone sequence. - Callsign Define callsign transmitted during normal transmissions. See Heading 10. - Callsign generator Speed: * Define Morse speed (0-40). Adjust value with number keys. - Callsign generator Only TX / TX

40、& LSP Callsign may be sent to loudspeaker - Callsign generator After TX: * sec Callsign generator is activated * seconds after the transmitter is keyed. Adjust value with number keys. - Callsign generator Every: * sec Callsign generator is activated every * seconds. Adjust value with number keys. Us

41、er Submenu! - LCD backlight Off after: * s LCD backlight is switched off automatically * seconds after last action. - My number * Define users personal 5-tone code. The transceiver produces an alarm tone on reception of this code. - Reply * This code may be transmitted when the personal code is rece

42、ived. - Reply Yes / No Enable/disable replying to personal code. - Key acceleration Accel.: X Define acceleration of up and down key. The longer the key is pressed, the faster frequencies will be stepped through. - Keys Repeat / Once If a key is held pressed, its function may be automatically repeat

43、ed. - Settings Update / Fixed When Update is selected, all settings are stored on switching off. Fixed allows settings to be stored manually using the next menu item. When switched on, the transceiver employs the previously stored settings. - Settings Store This allows you to store settings. - Memor

44、y Copy now This allows the contents of the 24C65/64 EEPROM to be copied. - Nederlands / English / Deutsch Select one of three languages. - Status Diagnosis If the error indicator F is visible, the cause of the problem may be called up by pressing the H button. 18. Calls The transceiver allows up to

45、10 different tone sequences to be stored. These tone sequences may be used to selectively call up stations. Calling: Display: - Press H (Select Function ) - Press 0 (Call: ) - Select the number/station to be called - Press # Defining the codes: Display: - Press H (Select Function ) - Press 0 (Call:

46、) - Select the number/station to be called. - Press H (Name: ) - Enter name, see Heading 10 - Press H to confirm (Nr. ) - Enter the number - Press H to confirm The H button is used to confirm entries. Cancel entry with any other key. - 7 - Appendix A. The FM1200 SB0 PMR with Handsfree Kit The FM1200

47、 SB0 is an FM1000 family member specially made for large trunked radio networks formerly operated by several large Electricity Boards in the UK. The FM1200 B0 has a Type-1 control board and was designed to cover 132-156 MHz. It usually comes with a remote control kit comprising a handsfree function based on a VOX. In addition to the transceiver proper and the FM1000 microphone you will have a remote mounting cable (5 m), a VOX/Junction Box, a numeric keypad display console with dashboard mounting socket, a VOX (condenser) microphone, a comb