Degen_DE-1103_user.pdf

《Degen_DE-1103_user.pdf》由会员分享，可在线阅读，更多相关《Degen_DE-1103_user.pdf（15页珍藏版）》请在收音机爱好者资料库上搜索。

1、OPERATION MANUAL PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVER DE1103 DE1103 PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVER Downloaded by? RadioAmateur.EU 1. Slide the battery lid. 2. Insert four AA batteries with correct polarity as shown in the compartment. 3

2、. Close the lid of compartment. OPERATING ON BATTERY BATTERY INSTALLATION Disconnect the AC adaptor plug with the unit while using batteries to supply power. Do not try to recharge no- rechargeable batteries. Do not mix old batteries with new ones. When the unit is not being used for a long period o

3、f time, remove batteries to avoid damage from battery leakage and corrosion. If battery leakage occurs, wipe the battery compartment with a soft cloth before inserting new batteries. BATTERY REPLACEMENT 1. When the sound becomes weak and distorted, battery power indicates , replace batteries or char

4、ge the batteries immediately, otherwise the unit will shut off automatically. 2. All memories are permanently stored. However, when the power supply is broken off, the clock reverts to the default setting 0:00, it needs to be reset. 3. The clock time will not lose if you replace new batteries in 3 m

5、inutes. 1 POWER SUPPLY . 6 SET THE CLOCK . . 1 POWER INDICATION . 3 BATTERY CHARGER . 4 BEFORE OPERATION. 7 TURN ONOFF THE UNIT . 8 VOLUME CONTROL & LOCAL / DX SWITCH . 9 BANDMETER BAND CONVERSION. 10 SET SLEEP TIME . 11 SET ALARM ONOFF . 12 TUNING INTO A STATION. 14 PRESET STATIONS . 18 DELETE STAT

6、IONS. . 19 HOLD & BACKLIGHT . . 20 TONE SELECTION & NARROW/WIDE BAND . 21 RESET & LINE OUT . 22 EARPHONES & FOLDING STAND . 23 RECEIVING SSB / CW . 24 USING ANTENNA . 25 SPECIFICATIONS. 27 POWER SUPPLY INDEX Power indicator is a trapeze pattern, it is hidden when receiving programme. User can check

7、power level by press . 3 If the power is exhausted, the unit will turn off automatically. When using rechargeable batteries, if appears, batteries need to be recharged. OPERATING ON AC 1. Plug the adaptor into a 220V AC power outlet. 2. Insert the adaptors small connector plug into the DC JACK . 25

8、2 If use AC adaptor to supply power, adaptor surface may a little heat. If the AC adaptor is connected, the unit automatically switches to the AC adaptor power, and installed batteries are no longer in use. Disconnect the AC adaptor with the outlet,if the AC adaptor is not being used. The backlight

9、will keep on illuminated when using AC adaptor. Remove the batteries if you want to use AC adaptor for a long period of time. Only Supplied AC adaptor should be used for this unit. POWER INDICATION POWER SUPPLY Left side AM ANT LODX 6V Medium Full More Lower VOL If constantly displays, the unit is i

10、n charging process. Please select high- quality rechargeable batteries. When using new rechargeable batteries or those which have not been used for a long time, charge them fully, then use them until they have completely run down. Repeat this cycle two more times, then those batteries can be used no

11、rmally. Do not leave fully charged batteries unused for a long time. Do not mix old batteries with new ones. CAUTIONS ! Do not try to charge dry batteries, avoid batteries leakage or explosion 1. Charging time should be set in power off mode, but you can turn on the unit and listen programme during

12、charging process. 2. There is no effect on battery charge if the unit is alarm on during charging. 3. Charging time can be calculated as: Charging hours = Battery Power (mAH) / 100mA ( charging current). 4. In power off mode, hold down to check rest charging hours. 5. Battery charge will be terminat

13、ed once the setting charging hours reaches. 6. Do not charge the batteries with fully power. Notes: 3. In power off mode, hold down button , in the meantime turn jog dial wheelTUNEto set charging time from 123 hours, then release button , charging starts. Or press number button to input charging hou

14、rs directly, then quickly press button to confirm. 4. Indicator flashes during battery charging. 5. When preset charging time reaches, the unit stops charging automatically. BATTERY CHARGE Install four AA rechargeable batteries with correct polarity. 2. Plug the adaptor into an 220V AC power outlet,

15、 connect the other side securely to DC Jack . 25 VOL VOL VOL VOL 54 BATTERY CHARGE BEFORE OPERATING Check Hold Button If appears in the display, the unit is locked. All buttons except HOLD button become inoperative. Unlock it to resume operation(Details refer page 20). Check Batteries/AC Adaptor Che

16、ck if batteries are inserted with correct polarity. Check if AC adaptor is connected in correct way. Please use supplied AC adaptor only. Check Local/DX Button Normally, set Local / DX button to DX position . 23 Display Time 1. When the unit is off, current time indicates in the display. 2. When the

17、 unit is on, press to display current time 5 seconds. The default time of this unit is 0:00, time has to be set in power off mode. Set The Clock 1. Hold down button for 2 seconds to set hour, hour number flashes for 30 seconds. 2. While hour number is flashing, turn the jog dial TUNEto set current h

18、our. 3. After hour setting, press to set minute, minute number flashes. 4. Turn jog dial wheel to adjust minutes. 5. After setting, press to confirm. SET THE CLOCK TIME TIME TIME TIME Please go to next step within 30 seconds, or the time setting will be invalid. 76 PLL FM STEREO/SW.MW.LW DUAL CONVER

19、SION SYNTHESIZED WORLD RECEIVER DE1103 SSB/268MEMORIES DEGENDEGENDEGENDEGEN 1234567890 BAND+ TIMESSBHOLD SLEEP ST/MOSCAN DELRESETFM AM STOREM/FVOL AL1AL2CHG 2. /4. 1. /3./5. Power On / Off the unit to turn on the unit manually, press again to turn it off. Each time turn on the unit, it will receive

20、the last station you ever heard. Alarm On / Off Two groups of alarm on /off time can be set in 24 hours. Station, volume can be set as well. The unit will turn on at preset time and will turn off after preset off time reaches. After setting, indicatorAlARM 1AlARM 2 constantly appears (Details refer

21、to Page 12 Sleep Timer Sleep time can be select from 1- 99 minutes. After setting, indicator SLEEPconstantly appears, when preset sleep time reaches, the unit will turn off automatically.(Details refer to Page 11). TURN ONOFF THE UNIT SLEEP SLEEP VOLUME CONTROL & LOCAL/DX SWITCH Volume Control Metho

22、d 1 Turn on the unit, press , VOL flashes for 3 seconds, turn jog dial wheel to adjust volume. Method 2 Press number button to input volume level directly, then press to confirm. For example: set volume to level 30 VOL Local /Dx Switch In SW or MW band, set LOCAL/DX switch to a proper position will

23、increase reception. Generally, set the switch to DX position, unless there is a strong interference or when you are listening to local stations. If LOCAL/DX switch is set to LOCAL position, some strong signal stations may receive clearly, but most weak signal stations can not be received. NOTE 23 LO

24、DX The volume is divided to 64 levels063, default level after reset the unit is level 40. When adjusting volume, corresponding level number appears in the display. VOL 03 VOL + 1234567890 BAND+ TIMESSBHOLD SLEEP MEMVOLSTORE CHGAL1 ST/MOSCAN AL2 DEL PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED

25、WORLD RECEIVER DE1103 SSB/268MEMORIES DEGENDEGENDEGEN RESETFM AM + - VOL PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVER DE1103 SSB/268MEMORIES DEGENDEGENDEGENDEGEN 1234567890 BAND+ TIMESSBHOLD SLEEP ST/MOSCAN DELRESETFM AM STOREM/FVOL AL1AL2CHG ALARM2SLEEPALARM1 SLEEP ALARM1 ALARM

26、2 Please go to next step within 3 seconds. 98 SET SLEEP TIME Method 1 1. Press number button to input sleep time, the input number appears for 3 seconds. 3. Indicator SLEEPconstantly appears in the display, sleep function works, when the setting sleep time reaches, the unit will shut off automatical

27、ly. 2. Press to confirm within 3 seconds. User can set sleep time from 199 minutes with the unit on or off either. Indicator will constantly display after sleep time is set. You have to go to next step within 3 seconds, otherwise, the unit will exit from sleep time setting. SLEEP SLEEP BANDMETER BAN

28、D CONVERSION Band Conversion After turn on the unit, press or repeatedly to select your desired band, band indicator shows corresponding band in the display. BAND+ FMMW60M49M41M 31M25M22M19M16M13M 90 75M SLEEP Method 21. Hold down , turn jog dial as well to select sleep time. Indicator SLEEPconstant

29、ly appears in the display. 1110 PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVER DE1103 SSB/268MEMORIES DEGENDEGENDEGENDEGEN 1234567890 BAND+ TIMESSBHOLD SLEEP ST/MOSCAN DELRESETFM AM STOREM/FVOL AL1AL2CHG FMMW60M49M41M31M25M22M19M16M13M 108 106 104 102 100 98 96 94 92 90 76 4.0 3.9

30、 3.8 3.7 3.6 3.5 3.4 3.3 3.2 5.4 5.3 5.2 5.1 5.0 4.9 4.8 4.7 4.6 6.4 6.3 6.2 6.1 6.0 5.9 5.8 5.7 5.6 9.9 9.8 9.7 9.6 9.5 9.4 9.3 9.2 9.1 7.4 7.3 7.2 7.1 7.0 6.9 6.8 6.7 6.6 12.4 12.3 12.2 12.1 12.0 11.9 11.8 11.7 11.6 11.5 14.4 14.3 14.2 14.1 14.0 13.9 13.8 13.7 13.6 13.5 17.915.8 15.7 15.6 15.5 15.

31、4 15.3 15.2 15.1 15.0 18.0 17.8 17.7 17.6 17.5 17.4 17.3 17.2 17.1 21.915.9 21.8 21.7 21.6 21.5 21.4 21.3 21.2 21.1 21.0 90 75M 1600 1510 1330 1240 1150 1060 880 700 610 520 1710 790 970 1420 2 1 PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVER DE1103 SSB/268MEMORIES DEGENDEGENDEGEN

32、DEGEN 1234567890 BAND+ TIMESSBHOLD SLEEP ST/MOSCAN DELRESETFM AM STOREM/FVOL AL1AL2CHG SLEEP 3. 1. 2. SET ALARM ONOFF 1. In power off mode, hold down button for 3 seconds, hour number flashes. 2. Turn jog dial TUNEto set hour, then press to set minutes. 3. TurnTUNEto set minutes, then press to go in

33、to station number setting. 4. TurnTUNEto select stored station number, then press to go into volume setting. 5. TurnTUNEto adjust volume, then press to set auto off time(from 599 minutes). 6. TurnTUNEto set auto off time. 7. Press to confirm setting. AlARM 1 constantly appears, when preset on / off

34、time reaches, the unit will on / of automatically. In power off mode, two groups of alarm on/off time can be set in 24 hours. Stationvolume can be set as well. Set Alarm 1 Cancel Alarm OnOff M/F SET ALARM ONOFF Set Alarm 2 In power off mode, hold down button for 3 seconds, hour number flashes. Other

35、 operations are same as Alarm 1 setting. 2. Finally, press to confirm, ALARM2constantly appears, when preset on / off time reaches, the unit will on / off automatically. STORE STORE Cancel Alarm 1 In power off mode, press button , the unit defaults last Alarm 1 setting. Press again to cancel, indica

36、tor AlARM 1disappears from the display. Cancel Alarm In power off mode, press button , the unit defaults last Alarm 2 setting. Press again to cancel, indicator AlARM 2disappears from the display. STORE STORE Note Press or to skip one step or confirm last setting. STORE If alarm 2 time is followed al

37、arm 1, the setting of station and volume will supersede alarm 1. Alarm on/ off is valid when you are listening radio programme. If you do not change the alarm setting, it is still valid on next day. 1312 M/F M/F M/F M/F M/F M/F M/F M/F PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVE

38、R DE1103 SSB/268MEMORIES DEGENDEGENDEGENDEGEN 1234567890 BAND+ TIMESSBHOLD SLEEP ST/MOSCAN DELRESETFM AM STOREM/FVOL AL1AL2CHG 1./7. PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVER DE1103 SSB/268MEMORIES DEGENDEGENDEGENDEGEN 1234567890 BAND+ TIMESSBHOLD SLEEP ST/MOSCAN DELRESETFM A

39、M STOREM/FVOL AL1AL2CHG ALARM1 ALARM 1 2./3./4. /5./6. BAND+ JOG DIAL TUNING TUNING INTO A STATION DIRECT FREQUENCY ENTRY TUNING INTO A STATION Direct frequency entry makes it extremely easy to tune into a station that you know its exact frequency. Frequency can be input without selecting band first

40、. 1. Turn on the unit, press button 09 to enter frequency. 2. Press corresponding button to confirm: Press to confirm a FM band station, press to confirm a AM band station. When use jog dial tuning, the frequency step for FM is 25K for AM is 1K. The highest turning speed is 80 step/circle. Sample 1F

41、M 89.80MHz 898 Sample 2AM 810KHz 8 Sample 3AM 120KHz 01 (FM banddecimal point and last digitals of 0can be ignored.) BAND+ Sample 4AM 10000KHz BAND+ 021 10000 Next number has to be entered within 3 seconds after the fore number is entered. If an invalid frequency is entered, Errwill appear in the di

42、splay. The frequency step for direct entry is 1KHz for AMand 100KHz for FM. 1. Turn on the unit, select desired band. 2. Press and turn the centre of the jog dialTUNEwith one finger to quickly go to a desired station, watch the change of the frequency. 3. When near a station, you can use two fingers

43、 to turn the jog dial wheel slowly to find the exact frequency. BAND+ 1234567890 BAND+ TIMESSBHOLD SLEEP MEMVOLSTORE CHGAL1 ST/MOSCAN AL2 DEL PLL FM STEREO/SW.MW.LW DUAL CONVERSION SYNTHESIZED WORLD RECEIVER DE1103 SSB/268MEMORIES DEGENDEGENDEGEN RESETFM AM + - MUSICNEWS LINE OUT TUNE NAR. WIDE LIGH

44、T OFFON FINE 1514 You can use below 4 methods to find a desired station, when tuning into a AM station, appears to indicate signal strength. The more steps appear, the stronger signal it is. AUTO SCAN TUNINGMEMORY SCAN TUNING TUNING INTO A STATIONTUNING INTO A STATION BAND+ In auto scan tuning, the frequency step is 100K for FM 1K for MW and 5K for SW. The unit will scan within the frequency range of chosen band or meter band. Turn on the