Kenwood_TK-7160_TK-7162_TK-8160_TK-8162_user.pdf

《Kenwood_TK-7160_TK-7162_TK-8160_TK-8162_user.pdf》由会员分享，可在线阅读，更多相关《Kenwood_TK-7160_TK-7162_TK-8160_TK-8162_user.pdf（35页珍藏版）》请在收音机爱好者资料库上搜索。

1、TK-7160/ TK-8160 TK-7162/ TK-8162 VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER INSTRUCTION MANUAL METTEUR-RCEPTEUR FM VHF/ METTEUR-RCEPTEUR FM UHF MODE DEMPLOI TRANSCEPTOR FM VHF/ TRANSCEPTOR FM UHF MANUAL DE INSTRUCCIONES RICETRASMETTITORE FM VHF/ RICETRASMETTITORE FM UHF MANUALE DI INSTRUZIONI VHF-FM-TR

2、ANSCEIVER/ UHF-FM-TRANSCEIVER BEDIENUNGSANLEITUNG VHF FM ZENDONTVANGER/ UHF FM ZENDONTVANGER GEBRUIKSAANWIJZING B62-1863-00 (E, E3, X2) 09 08 07 06 05 04 03 02 01 00 VHF FM TRANSCEIVER/ UHF FM TRANSCEIVER TK-7160/ TK-8160 TK-7162/ TK-8162 INSTRUCTION MANUAL ENGLISH i THANK YOU We are grateful you ha

3、ve chosen KENWOOD for your personal mobile applications. We believe this easy-to-use transceiver will provide dependable communications to keep personnel operating at peak efficiency. KENWOOD transceivers incorporate the latest in advanced technology. As a result, we feel strongly that you will be p

4、leased with the quality and features of this product. MODELS COVERED BY THIS MANUAL The models listed below are covered by this manual: TK-7160: VHF FM Transceiver TK-7162: VHF FM Transceiver TK-8160: UHF FM Transceiver TK-8162: UHF FM Transceiver NOTICES TO THE USER Government law prohibits the ope

5、ration of unlicensed transmitters within the territories under government control. Illegal operation is punishable by fine and/or imprisonment. Refer service to qualified technicians only. SAFETY: It is important that the operator is aware of, and understands, hazards common to the operation of any

6、transceiver. EXPLOSIVE ATMOSPHERES (GASES, DUST, FUMES, etc.) Turn OFF your transceiver while taking on fuel or while parked in gasoline service stations. Do not carry spare fuel containers in the trunk of your vehicle if your transceiver is mounted in the trunk area. INJURY FROM RADIO FREQUENCY TRA

7、NSMISSIONS Do not operate your transceiver when somebody is either touching the antenna or standing within 2 to 3 feet (60 to 90 cm) of it, to avoid the possibility of radio frequency burns or related physical injury. DYNAMITE BLASTING CAPS Operating the transceiver within 500 feet (150 m) of dynami

8、te blasting caps may cause them to explode. Turn OFF your transceiver when in an area where blasting is in progress, or where “TURN OFF TWO-WAY RADIO” signs have been posted. If you are transporting blasting caps in your vehicle, make sure they are carried in a closed metal box with a padded interio

9、r. Do not transmit while the caps are being placed into or removed from the container. ii PRECAUTIONS Observe the following precautions to prevent fire, personal injury, and transceiver damage. Do not attempt to configure the transceiver while driving; it is too dangerous. Do not disassemble or modi

10、fy the transceiver for any reason. Do not expose the transceiver to long periods of direct sunlight, nor place it near heating appliances. If an abnormal odor or smoke is detected coming from the transceiver, switch the transceiver power off immediately, and contact your KENWOOD dealer. Use of the t

11、ransceiver while you are driving may be against traffic laws. Please check and observe the vehicle regulations in your area. Do not use options not specified by KENWOOD. The transceiver operates in 12 V negative ground systems only! Check the battery polarity and voltage of the vehicle before instal

12、ling the transceiver. Use only the supplied DC power cable or a KENWOOD optional DC power cable. Do not cut and/or remove the fuse holder on the DC power cable. For passenger safety, install the transceiver securely using the supplied mounting bracket and screw set so the transceiver will not break

13、loose in the event of a collision. iii CONTENTS UNPACKING AND CHECKING EQUIPMENT. 1 SUPPLIED ACCESSORIES. 1 PREPARATION . 2 TOOLS REQUIRED. 2 POWER CABLE CONNECTION. 2 INSTALLING THE TRANSCEIVER. 3 CONNECTING A MICROPHONE. 4 GETTING ACQUAINTED . 5 FRONT PANEL. 5 DISPLAY (TK-7160/ TK-8160). 6 DISPLAY

14、 (TK-7162/ TK-8162). 7 REAR PANEL. 8 PROGRAMMABLE FUNCTIONS . 9 BASIC OPERATIONS . 10 SWITCHING POWER ON/ OFF. 10 ADJUSTING THE VOLUME. 10 SELECTING A ZONE AND CHANNEL. 11 TRANSMITTING. 11 RECEIVING. 11 SCAN . 12 PRIORITY SCAN. 12 ADD TO SCAN/ DELETE FROM SCAN. 13 REVERT CHANNEL. 13 DTMF CALLS . 14

15、STORE the transceiver will transmit the DTMF tones automatically as you enter the digits. STORING DTMF NUMBERS If Auto Dialing has been activated by your dealer, you can store DTMF numbers (16 digits maximum) in each of the 9 Auto Dial memory locations (1 9). 1Press the microphone # key. “ ” (TK-716

16、0/ TK-8160) or “ ” (TK-7162/ TK-8162) appears on the display. 2Enter the desired digits on the microphone keypad. You can enter the digits 0 9, A D, and #. To enter “#”, press and hold the PTT switch while entering the # key. To cancel, press any key on the transceiver front panel. 3Press the microp

17、hone # key, then enter a memory location number (1 9). 15 DIALING STORED DTMF NUMBERS 1Press the microphonekey. “ ” (TK-7160/ TK-8160) or “ ” (TK-7162/ TK-8162) appears on the display. 2Enter the desired memory location number (1 9). The digits stored in the selected location number appear on the di

18、splay. To cancel, press any key other than the PTT switch. 3Press the PTT switch. If programmed by your dealer, no DTMF tone will sound when “D” is transmitted. “D” can be used for a pause duration. The pause duration is programmed by your dealer. CLEARING STORED DTMF NUMBERS 1Press the microphone #

19、 key. “ ” (TK-7160/ TK-8160) or “ ” (TK-7162/ TK-8162) appears on the display. 2Press the microphone # key again. “” (TK-7160/ TK-8160) or “ ” (TK-7162/ TK-8162) appears on the display. To cancel, press any key other than 1 9. 3Enter the memory location number (1 9) you want to clear. The memory loc

20、ation number is cleared and the display returns to normal. REDIALING 1Press the microphonekey. “ ” (TK-7160/ TK-8160) or “ ” (TK-7162/ TK-8162) appears on the display. 2Press the microphone 0 key. On TK-7160/ TK8160 transceivers, the digits last dialed appear on the display. (Nothing is displayed on

21、 TK-7162/ TK-8162 transceivers.) If there is no data in the redial memory, an error tone will sound. To cancel, press any key other than the PTT switch. 3Press the PTT switch. Note: Switching the transceiver power OFF clears the redial memory. STUN This function is used when a transceiver is stolen

22、or lost. When the transceiver receives a call containing a stun code, either transmit mode will be disabled, or both receive mode and transmit mode will be disabled. The stun code is cancelled when the transceiver receives a call with a revive code. 16 QUIET TALK (QT)/ DIGITAL QUIET TALK (DQT) Your

23、dealer may have programmed QT or DQT signaling on your transceiver channels. A QT tone/ DQT code is a sub-audible tone/code which allows you to ignore (not hear) calls from other parties who are using the same channel. When a channel is set up with a QT tone or DQT code, squelch will only open when

24、a call containing a matching tone or code is received. Likewise, signals that you transmit will only be heard by parties whose QT/ DQT signaling matches your transceiver. If a call containing a different tone or code is made on the same channel you are using, squelch will not open and you will not h

25、ear the call. This allows you to ignore (not hear) these calls. Although it may seem like you have your own private channel while using QT/ DQT, other parties can still hear your calls if they set up their transceiver with the same tone or code. OPERATOR SELECTABLE TONE (OST) (TK-7160/ TK-8160 ONLY)

26、 You can change the preset encode and decode tones for the selected channel. Up to 40 tones can be pre-programmed by your dealer. 1Select your desired channel. 2Press the key programmed as Operator Selectable Tone. “” or the OST name or number appears on the display. 3Press the keys to select the de

27、sired OST name/ number. 4Use the transceiver the same as in a regular call; press the PTT switch to transmit and release it to receive. 5To exit OST mode and return to the preset encode and decode tones, press the S key. 17 CODE SQUELCH (ID CODE) Code Squelch is enabled or disabled by your dealer. T

28、his function turns the transceiver squelch OFF only when it receives the DTMF ID code that has been set up in your transceiver. Transceivers that do not transmit the correct code will not be heard. Consequently, you can communicate with a specific party without listening to other parties using the s

29、ame channel. Your dealer may also activate Group Call for your transceiver. This is useful when you want to send information to a number of units in a fleet. Ask your dealer for details. Note: Code Squelch cannot be used on this transceiver if Selective Call page 18 or DTMF Number Display page 28 ha

30、ve been programmed. RECEIVING When you receive a signal containing the correct ID code, the squelch opens and you will hear the call. The icon (TK-7160/ TK-8160) appears on the display and blinks. The TX/RX indicator flashes orange. To mute the speaker after the squelch opens, press the key programm

31、ed as Monitor. Your dealer can program the transceiver to mute the speaker after a specified time period elapses. If Transpond is programmed, an acknowledgment signal is returned to the calling station. Transpond does not function when you are called with a Group code. Transpond can send an alert to

32、ne, a transceiver ID code, or autodial memory location number 1 (refer to “STORING DTMF NUMBERS” on page 14). If Call Alert is programmed, an alert tone will sound when the correct ID code is received. TRANSMITTING 1Press and hold the microphone PTT switch. 2Enter the ID code of the transceiver you

33、want to call or enter a Group code on the microphone keypad. 3Use the transceiver the same as in a regular call; press the microphone PTT switch to transmit and release it to receive. Your dealer can program your transceiver with the following additional features: The icon (TK-7160/ TK-8160) appears

34、 on the display. When you release the microphone PTT switch, the squelch opens. If no signal is received for a pre-determined time, the speaker will mute. Pressing the key programmed as Monitor at any time will mute the speaker. 18 SELECTIVE CALL (TK-7160/ TK-8160 ONLY) Selective Call is enabled or

35、disabled by your dealer. This function is similar to Code Squelch page 17. The differences from Code Squelch are: You can send or receive Status codes containing up to 5 digits. Selective Call opens the squelch only when the transceiver receives a predetermined DTMF code in the correct sequence (3-d

36、igit or 4-digit ID code 1-digit Intermediate code Status code of up to 5 digits). Your dealer may also activate Group Call for your transceiver. This is useful when you want to send information to a number of units in a fleet. Ask your dealer for details. Note: Selective Call cannot be used on this

37、transceiver if Code Squelch page 17 or DTMF Number Display page 28 have been programmed. RECEIVING When you receive the correct ID and Intermediate codes, the squelch opens and you will hear the call. If a Status code is also received, the code will appear on the display. For example, if the Status

38、code “12345” was received, “” appears on the display. (“ ” appears in place of “ ” for group calls.) The icon appears on the display and blinks. When no Status code is received “” appears on the display. You can clear the Status code by pressing any key or returning the microphone to its hook. To mu

39、te the speaker after squelch opens, press the key programmed as Monitor. Your dealer can program the transceiver to mute the speaker after a specified time period elapses. If Transpond is programmed, an acknowledgment signal is returned to the calling station. Transpond does not function when you ar

40、e called with a Group code. Transpond can send an alert tone, a transceiver ID code, or autodial memory location number 1 (refer to “STORING DTMF NUMBERS” on page 14). If Call Alert is programmed, an alert tone will sound when the correct code is received. TRANSMITTING 1Press and hold the microphone

41、 PTT switch. 2Enter the ID code (or Group code) and Intermediate code of the transceiver you want to call on the microphone keypad. If desired, you can also enter a Status code of up to 5 digits. You can send codes the same way you make DTMF calls page 14. 3Use the transceiver the same as in a regul

42、ar call; press the microphone PTT switch to transmit and release it to receive. Your dealer can program your transceiver with the following additional features: The icon appears on the display. When you release the microphone PTT switch, the squelch opens. If no signal is received for a pre-determin

43、ed time, the speaker will mute. Pressing the key programmed as Monitor at any time will mute the speaker. 19 FleetSync: ALPHANUMERIC 2-WAY PAGING FUNCTION FleetSync is an Alphanumeric 2-way Paging Function and is a protocol owned by KENWOOD Corporation. FleetSync enables a variety of paging function

44、s on your transceiver, some of which depend on dealer programming. The TK-7162/ TK-8162 only has access to the PTT ID function of the FleetSync feature. Note: Your transceiver functions include either FleetSync or 5-tone Signaling page 22, but not both. SELCALL (SELECTIVE CALLING) A Selcall is a voice call to a particular station or to a group of stations. Transmitting (TK-7160/ TK-8160 Only) 1Select your desired zone and channel. 2Press th