Vertex_VX-4500_4600_user_2013.pdf

《Vertex_VX-4500_4600_user_2013.pdf》由会员分享，可在线阅读，更多相关《Vertex_VX-4500_4600_user_2013.pdf（32页珍藏版）》请在收音机爱好者资料库上搜索。

1、VX-4500 VX-4600 Operating Manual VX-4600VX-4500 Six Programmable Function Keys 5-tone Encode/Decode ARTS (Auto Range Transpond System) Dimmer/Lamp Horn Alert Public Address Lock Beep OFF Encryption Scan Group Scan Dual Watch FM-Scan (Follow-Me Scan) TA Scan VOX prOgraMMaBle FunctiOns/Features ( : VX

2、-4600 only) 2-tone Encode/Decode MDC-1200 Encode/Decode REC the red “TX” indicator will disappear and transmission will cease soon thereafter. On the VX-4600, “TIME OUT” will be indicated on the display. To resume transmitting, you must release the PTT switch and wait for the “penalty timer” to expi

3、re (if you press the PTT switch before this timer expires, the timer restarts, and you will have to wait another “penalty” period) Key Lock In order to prevent accidental operating function/feature change or inadvertent transmission, various aspects of the front panels keys may be locked out. To act

4、ivate the Locking feature, press and hold in the P1 key while turning the radio on. To disable the Locking feature, repeat this power-on procedure. aDVanceD OperatiOn Programmable Function (PF) Keys The VX-4500/-4600 includes six Programmable Function (PF) keys. The PF but- ton functions can be cust

5、omized, via programming by your Vertex Standard dealer, to meet your communications/network requirements. Some features may require the purchase and installation of optional internal accessories. The possible PF key programming features are illustrated below, and these functions are explained on the

6、 pages to follow. For further details, contact your Vertex Standard dealer. For future reference, check the box next to the function that has been assigned to each PF key on your particular radio, and keep it handy. Basic OperatiOn OF the transceiVer VX-4500/-4600 SerieS Operating Manual9 aDVanceD O

7、peratiOn : This function cannot assign to VX-4500. FunctiOn prOgraMMaBle Key (press Key/press it will pause each time it inds a channel on which someone is speaking. Press (or press and hold) the assigned programmable key again to disable scan- ning. Operation will revert to the programmed revert ch

8、annel. Note: Your Vertex Standard dealer may have programmed your radio to stay on one of the following channels if you press the PTT switch during the scanning pause: “Scan Pause” channel (“Talk Back”) “Last Busy” channel “Priority-1/-2” channel “User Programmed” channel (“Select Channel”) “Scan St

9、art” channel VX-4500/-4600 SerieS Operating Manual16 group Scan (This function is only available in the VX-4600) The Scanning feature is used to monitor multiple channels programmed into the transceiver. While scanning, the transceiver will check each channel of the pro- grammed group for the presen

10、ce of the signal, and will stop on a channel if a sig- nal is present. Press (or press and hold) the assigned programmable key to activate the scanning on the selected groups. Dual watcH The Dual Watch feature is similar to the SCAN feature, except that only two chan- nels are monitored: The current

11、 operating channel; and The Priority-1/-2 channel. To activate Dual Watch: Press (or press and hold) the assigned programmable key. The scanner will search the two channels; it will pause each time it inds a channel on which someone is speaking. To stop Dual Watch: Press (or press and hold) the assi

12、gned programmable key. Operation will revert to the “Dual Watch Start” channel. FM-Scan (Follow-Me Scan) FM-Scan (Follow-Me Scan) feature checks a User-assigned Priority Channel regu- larly as you scan the other channels. Thus, if only Channels 1, 3, and 5 (of the 8 available channels) are designate

13、d for “Scanning,” the user may nonetheless assign Channel 2 as the “User-assigned” Priority Channel via the FM-Scan (Follow-Me Scan). To activate the FM-Scan (Follow-Me Scan), irst select the channel you want to designate as the “User-Assigned Priority Channel” and press (or press and hold) the assi

14、gned programmable key. Then press (or press and hold) the Channel Up/ Down key (generally the / key) to recall to the “Scanning Start” chan- nel which has been programmed by your dealer to activate the scanner. When the scanner stops on an “Active” channel, the User-assigned Priority Channel will au

15、tomatically be checked every few seconds; if activity is found on the User-as- signed Priority Channel, the radio will switch between it and the Dealer-Assigned Priority Channel, if any. aDVanceD OperatiOn VX-4500/-4600 SerieS Operating Manual17 aDVanceD OperatiOn Scan Set Press (or press and hold)

16、the assigned programmable key to add/delete the current channel to/from your scanning list. In the VX-4500, when you delete channel, the “A” or “B” indicator will turn off, if the “SCAN CH” status is assigned to the “A” or “B” indicator. To restore a particular channel to your scanning list, press (

17、or press and hold) the assigned programmable key again; the “A” or “B” indicator will illuminates, if the “SCAN CH” status is assigned to the “A” or “B” indicator. In the VX-4600, when you delete channel, the display indicates “- SCN SKIP -” briely and the “” icon will disappear from the display. To

18、 restore a particular channel to your scanning list, press (or press and hold) the assigned programmable key again; the display indicates “- SCN SET -” briely and “” icon will appear on the display. Furthermore, press (or press and hold) the assigned programmable key while the scanner is paused, thi

19、s removes the channel from the scan list temporarily. group Scan Set (This function is only available in the VX-4600) You may wish to have the Scanner pass through more than one Group during the scanning process (normally, scanning is performed within the current group only). To include the current

20、Group in the scanning loop, press (or press and hold) the assigned programmable key (the “” icon will appear on the display). To remove a current Group from Group Scan, press (or press and hold) the assigned pro- grammable key again (the “” icon will disappear from the display). ta Scan Press (or pr

21、ess and hold) the assigned programmable key to toggle the TA (Talk Around) scan feature “On” and “Off.” While TA scan is enabled, the transceiver will search both the transmit and receive frequencies (In the VX-4600, the “” icon will blink on the display). When a signal is encountered on the receive

22、 frequency, the transceiver will pause until the signal disappears (In the VX-4600, “” icon will appear but not blink). When a signal is encountered on the transmit frequency, the transceiver will check for ac- tivity on the receive frequency every few seconds (interval programmed by your Vertex Sta

23、ndard dealer). Note: The TA Scan feature does not activate on the Simplex Channel. VX-4500/-4600 SerieS Operating Manual18 talk arounD Press (or press and hold) the assigned programmable key to activate the Talk Around feature when you are operating on duplex channel systems (separate re- ceive and

24、transmit frequencies, utilizing a “repeater” station). The Talk Around feature allows you to bypass the repeater station and talk directly to a station that is nearby. This feature has no effect when you are operating on “simplex” chan- nels, where the receive and transmit frequencies are already th

25、e same. In the VX-4600, when the “TA” function is activated, the “” icon will be indi- cated on the display. Note that your Vertex Standard may have made provision for “Talk Around” chan- nels by programming “repeater” and “Talk Around” frequencies on two adjacent channels. If so, the key may be use

26、d for one of the other Pre-Programmed Func- tions. Note: The Talk Around feature does not activate on the Simplex Channel. reSet Press (or press and hold) the assigned programmable key to reset the RFC (Ready for Communication) condition. call 1 to call 5 Press (or press and hold) the assigned progr

27、ammable key to send a 2-Tone or 5-Tone sequential burst which is pre-programmed. coDe up/Down (This function is only available in the VX-4600) Press (or press and hold) the assigned programmable key to select a 2-Tone or 5-Tone encode code from the pre-programmed encode list. aDVanceD OperatiOn VX-4

28、500/-4600 SerieS Operating Manual19 aDVanceD OperatiOn coDe Set (This function is only available in the VX-4600) Press (or press and hold) the assigned programmable key to change the 5-Tone encoding digit. To change the tones, select the desired digit using the P1/P2 keys (or MH- 75A8J s A/B keys),

29、then change the number using the / keys. Press the P4 key (or MH-75A8J s D key) to store the new setting. The dis- play indicates “- SET -” briely, then reverts to the normal channel indication. You may cancel the new setting by pressing the P3 key (or MH-75A8J s C key). In this case, the display in

30、dicates “- CANCEL -” briely. You may enter the 5-Tone encoding code directly from the microphones numeric key ( 0 - 9) and key (wild card), if the optional MH-75A8J microphone is used. SpeeD Dial (This function is only available in the VX-4600) Your Vertex Standard dealer may have pre-programmed Aut

31、o-Dial telephone num- ber memories into your radio. To dial a number: If the optional MH-75A8J microphone is used, press (or press and hold) the as- signed programmable key, then press the microphones numeric key (0 - 9 ) corresponding to the Auto-Dial memory number which is provided by your Vertex

32、Standard Dealer, then press the PTT switch. The DTMF tones sent dur- ing the dialing sequence will be heard in the speaker. If the normal (without keypad) microphone is used, press the / keys to select the Auto-Dial memory number which is pre-programmed by your Vertex Standard dealer, then press the

33、 PTT switch. The DTMF tones sent during the dialing sequence will be heard in the speaker. DtMF coDe Set (This function is only available in the VX-4600 and requires the Optional MH-75A8J 16-Keypad Microphone) Press (or press and hold) the assigned programmable key to start storing the DTMF dialing

34、sequence. After entering to enter all DTMF digits from the MH- 75A8Js keypad, you can transmit the code by pressing the PTT switch. VX-4500/-4600 SerieS Operating Manual20 call When using the DTMF Paging System This feature, if enabled, allows the user to change the 3-digit Page Call code, used to c

35、all other similarly-equipped stations. Press (or press and hold) the assigned programmable key, followed by the three digits representing the Page Call code of the station you wish to call. Three tones will be heard after the last key is pressed (the new code will now be transmitted). The receiver s

36、quelch of the other station will be opened, and you can begin com- munication. When using the 2-tone/5-tone Signaling System This feature, if enabled, press (or press and hold) the assigned programmable key to send a 2-tone/5-tone sequential tone. When using the MDC1200 System This feature, if enabl

37、ed, press (or press and hold) the assigned programmable key to send an MDC1200 code. Press (or press and hold) the assigned programmable key to enter the “Call Menu” mode. Press the / keys (or P1/P2 keys) to select the desired Call mode, then press the P4 key to accept the selection. (You may cancel

38、 the selection by pressing the P3 key). Press the / (or P1/P2 keys) to select the station to be called. You may enter the stations ID number (four digits) directly from the micro- phones key (0 - 9, A - D, #: substitute for “E”, and : wild card), if the optional MH-75A8J microphone is used. Press th

39、e PTT switch to send an MDC1200 call. StatuS Set (This function is only available in the VX-4600) Press (or press and hold) the assigned programmable key to change the 5-tone status code. To change the status code, select the desired digit by pressing the P1 key, then change the number by pressing t

40、he P2/P3 key, and store the number by pressing the P4 key. You may enter the 5-tone status code directory from the microphones numeric key ( 0 - 9), if the optional MH-75A8J microphone is used. aDVanceD OperatiOn VX-4500/-4600 SerieS Operating Manual21 aDVanceD OperatiOn StatuS up/Down (This functio

41、n is only available in the VX-4600) Press (or press and hold) the assigned programmable key to select a 5-tone status code from the pre-deined status list. StatuS cHeck (This function is only available in the VX-4600) Press (or press and hold) the assigned programmable key to check the 5-tone re- ce

42、ive status code. When you press this key, the display will indicate the “Message” corresponding to the receive status condition per the pre-deined status list. Duty Press (or press and hold) the assigned programmable key to toggle the Duty func- tion of the 2-tone/5-tone decoder “On” and “Off”. When

43、 the Duty function is set to “On”, the user will always hear (depending on the sub-audio signaling) all trafic on the paging channel. The radio will sound the paging alert when it receives the programmed 2-tone/5-tone code. When the Duty function is set to “Off”, the user will NOT hear normal radio

44、traf- ic on the paging channel. The radio will sound the paging alert and unmute only when it receives the programmed 2-tone/5-tone code. iD cHeck (This function is only available in the VX-4600) This function allows logged ID of the DTMF Signaling and 5-tone Signaling to be reviewed and relayed (5-

45、tone Signaling only) to a speciic station: Press (or press and hold) the assigned programmable key to display the logged ID of the DTMF Signaling and 5-tone Signaling. Press the P4 key to select the category (“DTMF Signaling” or “5-tone Sig- naling”) to be reviewed, then press the / keys to select t

46、he ID. Press the P2 key to toggle the display between the “ID code display” and “Tag display”. Press the P1 key to send the Call back, when recalling the ID of the “5-tone Signaling”, if desired. option SwitcH 1 Activates the optional accessory “1” while pressing the assigned programmable key. optio

47、n SwitcH 2 Press the assigned programmable key to toggle the optional accessory “2” “On” and “Off”. VX-4500/-4600 SerieS Operating Manual22 aDVanceD OperatiOn rec (r eQuireS tHe DVS-8 Voice Storage unit) Press (or press and hold) the assigned programmable key to enable the Voice Re- cording Mode. Wh

48、en an incoming signal is received (the squelch opens and audio passes), the incoming audio will be recorded. The “” icon will lash during au- dio recording, and the “” icon will remain on once recording is complete. play (r eQuireS tHe DVS-8 Voice Storage unit) Press (or press and hold) the assigned

49、 programmable key to play back the last message. Press (or press and hold) the assigned programmable key again to stop the play- back. While playback is proceeding, you may press the P1 key (or MH-75A8J s A key) to jump to the previous message, or press the P2 key (or MH-75A8J s B key) to jump to the next message. Furthermore, press the P4 key (or MH-75A8Js D key) to delete all messages and stop the play-back. tX SaVe DiSaBle Press (or press and hold) the assigned programmable key to disable the Transmit Saver, if you are operating in a l