Sony_XR-CA360_XR-CA360X_serv.pdf

《Sony_XR-CA360_XR-CA360X_serv.pdf》由会员分享，可在线阅读，更多相关《Sony_XR-CA360_XR-CA360X_serv.pdf（44页珍藏版）》请在收音机爱好者资料库上搜索。

1、SERVICE MANUAL E model FM/AM/CASSETTE CAR STEREO Saudi Arabia model FM/MW/SW CASSETTE CAR STEREO E Model XR-CA360/CA360X Saudi Arabia Model XR-CA360 SPECIFICATIONS XR-CA360/CA360X Photo: XR-CA360 Ver 1.2 2003.12 CA 9-874-258-03Sony Corporation 2003L05-1e Vehicle Company C 2003.12Published by Sony En

2、gineering Corporation Model Name Using Similar MechanismNEW Tape Transport Mechanism TypeMG-36SZ13-32 Cassette player section Tape track4-track 2-channel stereo Wow and flutter0.13 % (WRMS) Frequency response30 15,000 Hz Signal-to-noise ratio55 dB Tuner section FM Tuning range (E model) FM tuning in

3、terval: 50 kHz/200 kHz switchable 87.5 108.0 MHz (at 50 kHz step) 87.5 107.9 MHz (at 200 kHz step) Aerial terminalExternal aerial connector Intermediate frequency10.7 MHz/450 kHz Usable sensitivity9 dBf Selectivity75 dB at 400 kHz Signal-to-noise ratio67 dB (stereo), 69 dB (mono) Harmonic distortion

4、 at 1 kHz 0.5 % (stereo), 0.3 % (mono) Separation35 dB at 1 kHz Frequency response30 15,000 Hz AM (E model) Tuning rangeAM tuning interval: 9 kHz/10 kHz switchable 531 1,602 kHz (at 9 kHz step) 530 1,710 kHz (at 10 kHz step) Aerial terminalExternal aerial connector Intermediate frequency10.7 MHz/450

5、 kHz Sensitivity30 V Power amplifier section OutputsSpeaker outputs (sure seal connectors) Speaker impedance4 8 ohms Maximum power output 45 W 4 (at 4 ohms) General OutputsAudio output Power aerial relay control lead Power amplifier control lead InputsBUS control input terminal BUS audio input termi

6、nal Tone controlsLow: 10 dB at 60 Hz (Xplod) Mid: 10 dB at 1 kHz (Xplod) High: 10 dB at 10 kHz (Xplod) Power requirements12 V DC car battery (negative earth) DimensionsApprox. 178 50 178 mm (w/h/d) Mounting dimensionsApprox. 182 53 161 mm (w/h/d) MassApprox. 1.2 kg Supplied accessoriesParts for inst

7、allation and connections (1 set) Front panel case (1) Design and specifications are subject to change without notice. Tuning range (Saudi Arabia model) 87.5 108.0 MHz MW/SW (Saudi Arabia model) Tuning rangeMW: 531 1,602 kHz SW1: 2,940 7,735 kHz SW2: 9,500 18,135 kHz (except for 10,140 11,575 kHz) Ae

8、rial terminalExternal aerial connector Intermediate frequency10.7 MHz/450 kHz Sensitivity30 V 2 XR-CA360/CA360X Flexible Circuit Board Repairing Keep the temperature of the soldering iron around 270 C dur- ing repairing. Do not touch the soldering iron on the same conductor of the circuit board (wit

9、hin 3 times). Be careful not to apply force on the conductor when soldering or unsoldering. Notes on chip component replacement Never reuse a disconnected chip component. Notice that the minus side of a tantalum capacitor may be dam- aged by heat. TABLE OF CONTENTS SERVICING NOTES.2 1.GENERAL Locati

10、on of Controls .3 Setting the Clock.3 2.DISASSEMBLY 2-1.Disassembly Flow .7 2-2.Sub Panel.7 2-3.Mechanism Deck (MG-36SZ13-32).8 2-4.MAIN Board .8 2-5.Heat Sink .9 2-6.Bracket (MD) .9 2-7.DC Motor (Capstan/Reel) (M901) . 10 2-8.Main Belt, Sub Belt (C) . 10 2-9.Magnetic Head (Playback) (HP901) . 11 3.

11、MECHANICAL ADJUSTMENTS. 12 4.ELECTRICAL ADJUSTMENTS Tape Deck Section . 12 Tuner Section . 13 5.DIAGRAMS 5-1.Note for Printed Wiring Boards and Schematic Diagrams . 14 5-2.Printed Wiring Board MAIN Board . 15 5-3.Schematic Diagram MAIN Board (1/2) . 16 5-4.Schematic Diagram MAIN Board (2/2) . 17 5-5

12、.Printed Wiring Board CONTROL Board . 18 5-6.Schematic Diagram CONTROL Board . 19 5-7.IC Pin Function Description . 21 6.EXPLODED VIEWS 6-1.General Section . 23 6-2.Front Panel Section . 24 6-3.MAIN Board Section . 25 6-4.Mechanism Deck Section (MG-36SZ13-32) . 26 7.ELECTRICAL PARTS LIST. 27 SERVICI

13、NG NOTES SERVICE POSITION In checking the control board and main board, prepare two jigs (extension (MD) cord J-2502-060-1 and connection cable for F/P to main J-2502-072-1). Note of replacing of the IC1 In this set, the IC1 on the MAIN board is changed from the mid- way of the production. When the

14、replacing of the IC1, be sure to check the model name printed by IC, and replace the IC1 by following the instructions below. When replacing of the IC1 (MN101C49HAS) Replace the IC1 with the MN101C49HEA (Part No.: 6-603- 178-01), and replace the TU101 (A-3220-944-A) simultaneously. When replacing of

15、 the IC1 (MN101C49HEA) Perform the usual replacing. main board (CN600) mechanism deck main board (CN350) main board (CN300) control board (CN900) connect jig (connection cable for F/P to main J-2502-072-1) to the main board (CN600) and control board (CN900). connect jig (extention (MD) cord J-2502-0

16、60-1) to the main board (CN300, CN350) and mechanism deck. Ver 1.2 3 XR-CA360/CA360X SECTION 1 GENERAL This section is extracted from instruction manual. Location of controls XR-CA360X/CA360 SOURCE MODE SEL RELEASE EQ3 DSPL ATT DISCREPSHUF ATA 123456BTMOFFSENS SEEK DIR Refer to the pages listed for

17、details. 1 SOURCE (Radio/CD/MD) button 2 MODE button During radio reception: Band select During CD/MD playback: CD/MD unit select 3 Volume +/ button 4 Z (eject) button 5 Display window 6 m/M (fast winding)/DIR (tape transport direction change) buttons 7 SEEK button Seek Automatic Music Sensor Manual

18、 search 8 DSPL (display mode change) button 9 EQ3 button 0 RELEASE (front panel release) button qa SEL (select) button qs RESET button (located on the front side of the unit behind the front panel) qd ATT (attenuate) button qf Number buttons During radio reception: Preset number select During CD/MD

19、playback: (1)DISC (2)DISC + (3)REP (4)SHUF qg Frequency select switch (E model) (located on the bottom of the unit) See “Frequency select switch” in the Installation/Connections manual. qh BTM/ATA button qj SENS button qk OFF button* * Warning when installing in a car without ACC (accessory) positio

20、n on the ignition key switch Be sure to press (OFF) on the unit for 2 seconds to turn off the clock display after turning off the engine. When you press (OFF) momentarily, the clock display does not turn off and this causes battery wear. Setting the clock The clock uses a 12-hour digital indication.

21、 Example: To set the clock to 10:08 1Press (DSPL) for 2 seconds. The hour indication flashes. 1 Press either side of the volume button to set the hour. 2 Press (SEL). The minute indication flashes. 3 Press either side of the volume button to set the minute. 2 Press (DSPL). The clock starts. After th

22、e clock setting is complete, the display returns to normal play mode. to go forward to go back to go forward to go back 4 XR-CA360/CA360X B A BUS AUDIO IN BUS CONTROL IN AUDIO OUT REAR BUS AUDIO IN BUS CONTROL IN Source selector* Selector de fuente* XA-CA30 *not supplied no suministrado 2 Cautions T

23、his unit is designed for negative earth 12 V DC operation only. Do not get the wires under a screw, or caught in moving parts (e.g. seat railing). Before making connections, turn the car ignition off to avoid short circuits. Connect the yellow and red power input leads only after all other leads hav

24、e been connected. Run all earth wires to a common earth point. Be sure to insulate any loose unconnected wires with electrical tape for safety. Notes on the power supply cord (yellow) When connecting this unit in combination with other stereo components, the connected car circuits rating must be hig

25、her than the sum of each components fuse. When no car circuits are rated high enough, connect the unit directly to the battery. Parts Iist (1) The numbers in the list are keyed to those in the instructions. The bracket 1 and the protection collar 5 are attached to the unit before shipping. Before mo

26、unting the unit, use the release keys 7 to remove the bracket 1 and the protection collar 5 from the unit. For details, see “Removing the protection collar and the bracket (4)” on the reverse side of the sheet. Keep the release keys 7 for future use as they are also necessary if you remove the unit

27、from your car. Caution Handle the bracket 1 carefully to avoid injuring your fingers. Note Before installing, make sure that the catches on both sides of the bracket 1 are bent inwards 2 mm. If the catches are straight or bent outwards, the unit will not be installed securely and may spring out. Con

28、nection example (2) Notes (2-B-) Be sure to connect the earth cord before connecting the amplifier. If you connect an optional power amplifier and do not use the built-in amplifier, the beep sound will be deactivated. Tip (2-B-) For connecting two or more CD/MD changers, the source selector XA-C30 (

29、optional) is necessary. Connection diagram (3) 1 To a metal surface of the car First connect the black earth lead, then connect the yellow and red power input leads. 2 To the power aerial control lead or power supply lead of aerial booster amplifier Notes It is not necessary to connect this lead if

30、there is no power aerial or aerial booster, or with a manually- operated telescopic aerial. When your car has a built-in FM/AM aerial in the rear/side glass, see “Notes on the control and power supply leads.” 3 To AMP REMOTE IN of an optional power amplifier This connection is only for amplifiers. C

31、onnecting any other system may damage the unit. 4 To the +12 V power terminal which is energised in the accessory position of the ignition key switch Notes If there is no accessory position, connect to the +12 V power (battery) terminal which is energised at all times. Be sure to connect the black g

32、round lead to a metal surface of the car first. When your car has a built-in FM/AM aerial in the rear/side glass, see “Notes on the control and power supply leads.” 5 To the +12 V power terminal which is energised at all times Be sure to connect the black ground lead to a metal surface of the car fi

33、rst. 1 Catch Notes on the control and power supply leads The power aerial control lead (blue) supplies +12 V DC when you turn on the tuner. When your car has built-in FM/AM aerial in the rear/ side glass, connect the power aerial control lead (blue) or the accessory power input lead (red) to the pow

34、er terminal of the existing aerial booster. For details, consult your dealer. A power aerial without relay box cannot be used with this unit. Memory hold connection When the yellow power input lead is connected, power will always be supplied to the memory circuit even when the ignition key is turned

35、 off. Notes on speaker connection Before connecting the speakers, turn the unit off. Use speakers with an impedance of 4 to 8 ohms, and with adequate power handling capacities to avoid its damage. Do not connect the speaker terminals to the car chassis, or connect the terminals of the right speakers

36、 with those of the left speaker. Do not connect the earth lead of this unit to the negative () terminal of the speaker. Do not attempt to connect the speakers in parallel. Connect only passive speakers. Connecting active speakers (with built-in amplifiers) to the speaker terminals may damage the uni

37、t. To avoid a malfunction, do not use the built-in speaker wires installed in your car if the unit shares a common negative () lead for the right and left speakers. Do not connect the units speaker cords to each other. 5 XR-CA360/CA360X BUS AUDIO IN AUDIO OUT BUS AUDIO IN BUS CONTROL IN AUDIO OUT RE

38、AR Supplied with XA-C30 Suministrado con el XA-C30 from car aerial de antena de automvil Source selector (not supplied ) Selector de fuente (no suministrado ) XA-C30 1 4 5 2 AMP REM ANT REM 6 RCA pin cord (not supplied) Cable con clavijas RCA (no suministrado) Max. supply current 0.3 A Corriente mx.

39、 de alimentacin de 0,3 A Max. supply current 0.1 A Corriente mx. de alimentacin de 0,1 A Fuse (10 A) Fusible (10 A) Red Rojo Yellow Amarillo Black Negro Blue Azul Blue/white striped Con raya azul/blanca White Blanco Green Verde Purple Prpura White/black striped Con raya blanca/negra Grey/black strip

40、ed Con raya gris/negra Green/black striped Con raya verde/negra Purple/black striped Con raya violeta/negra Grey Gris 3 Left Izquierdo Right Derecho Left Izquierdo Right Derecho Supplied with the CD/MD changer Suministrado con el cambiador de CD/MD Equipment used in illustrations (not supplied) Equi

41、po utilizado en las ilustraciones (no suministrado) Front speaker Altavoces delanteros Rear speaker Altavoces traseros Power amplifier Amplificador de potencia CD/MD Cambiador de CD/MD 3 Precautions Choose the installation location carefully so that the unit will not interfere with normal driving op

42、erations. Avoid installing the unit in areas subject to dust, dirt, excessive vibration, or high temperatures, such as in direct sunlight or near heater ducts. Use only the supplied mounting hardware for a safe and secure installation. Mounting angle adjustment Adjust the mounting angle to less than

43、 20. Removing the protection collar and the bracket (4) Before installing the unit, remove the protection collar 5 and the bracket 1 from the unit. 1Remove the protection collar 5. 1 Engage the release keys 7 together with the protection collar 5 . 2 Pull out the release keys 7 to remove the protect

44、ion collar 5. 2Remove the bracket 1. 1 Insert both release keys 7 together between the unit and the bracket until they click. 2 Pull down the bracket 1, then pull up the unit to separate. Frequency select switch (E model) The AM (FM) tuning interval is factory-set to the 9 k (50 k) position. If the

45、frequency allocation system of your country is based on 10 kHz (200 kHz) interval, set the switch on the bottom of the unit to the 10 k (200 k) position before making connections. Warning when installing in a car without ACC (accessory) position on the ignition key switch Be sure to press (OFF) on the unit for two seconds to turn off the clock display after turning off the engine. When you press (OFF) only momentarily, the clock display does not turn off and this causes battery wear. RESET button When the installation and connect