Ten-Tec_1253_review_K8JHR_2013.pdf

《Ten-Tec_1253_review_K8JHR_2013.pdf》由会员分享，可在线阅读，更多相关《Ten-Tec_1253_review_K8JHR_2013.pdf（3页珍藏版）》请在收音机爱好者资料库上搜索。

1、 As I had limited previous kit-building experience, I built the Ten-Tec Model 1253 Nine-Band Regenerative HF Radio Kit in a several short sessions spread out over several days. More experienced kit builders could be expected to complete this kit in much less time, but I took my time and worked at a

2、leisurely pace. Overall, a good kit building experience. The kit included all required parts, which were packaged in several zip-lock plastic bags. It was fairly easy to quickly identify and inventory all parts. The instruction booklet was reasonably clear, concise, and adequate to guide the novice

3、builder. My sole objection is it appears to have been reproduced on a standard copy machine and should have higher print clarity and quality. The builder is well advised to pay attention to any separate error corrections and updates printed on separate sheets of paper, and take time to mark all such

4、 changes and updates in the main instruction booklet before starting construction. Sidebar Considering we live in an era of modern computer word processing and inexpensive, high quality laser printers, there is no excuse for not producing all documents with these applications, and all updates or cha

5、nges should be made to the original document before its inclusion in the kit as delivered to builder. I suspect these kits were put up some time ago, so I doubt it would be profitable to rewrite this manual unless and until current supplies run out or major revisions in design or component parts are

6、 made that necessitate overhauling the instruction manual. I would to it, if only to update the look and feel of the kit to the builder. _ Ten-Tec Model 1253 Regenerative HF Radio Kit, Page 1 of 3. K8JHR copyright 2013 TEN-TEC MODEL 1253 REGENERATIVE RADIO KIT Photos (above) show components before c

7、ommencing assembly. Overall, a good kit experience. A few Suggestions, Minor Concerns, and Issues to consider: 1. One problem was a temporary show stopper. The audio amplifier IC chip burned out during a scheduled progress test. While a bit disconcerting, Ten-Tec agreed it was a defective part, and

8、provided a replacement without delay. It is hard to beat Ten-Tec customer service. The service technicians are just a phone call away, and are patient, courteous and helpful. 2. Building the front panel circuit board so the LEDs line up with the respective holes in the front panel can be tricky. Car

9、eful workmanship will be rewarded with easier alignment during final assembly. Some builders report the little holes might be filled with paint, and have remedied this using an appropriate size twist drill bit. I did not encounter this problem, but the LEDs are hard to line up in any case. 3. Some b

10、uilders suggest placing a piece of window screen, fine metal mesh or fabric across the speaker to prevent dust and small objects from falling into the top-mounted speaker grill. I eschewed this advice, although it seems like a good idea. Some builders have found the speaker vibrates or rattles, and

11、cure this with some well placed electrical tape or rubber padding. My unit did not require this modification, although I can see how it could happen. 4. Live and Learn Dept. - I got confused over inconsistent markings on a some of the resistors, as some resistors had “violet” value bands which were

12、a much lighter color violet, while others had bands which were more dark purple than violet. Ten-Tec Service said some manufacturers use substantially different colors when marking resistor values, as is evident in the attached photo. This taught me to use my digital multimeter to verify correct val

13、ues before installing various components. 5. Not a big deal, but the wires running from the front panel to the rear panel should be cut a little longer than specified in order to facilitate final assembly and better accommodate the battery holder. 6. Not a big deal, but the builder may wish to use s

14、maller gauge wire (zip) ties, and, perhaps, use additional ties, to better anchor and organize the wires in the final construction stages. 7.I left the battery compartment out of my finished radio, as I do not intend to operate the unit on battery power. I might better have stored it inside the rig,

15、 to save storage space and minimize the chances I misplace it, but I opted to leave it out. You be the judge. 8. Another builder suggests using an SLA gel cell to run the rig for an extended period, which could be recharged with an inexpensive, but appropriate, charger at relatively low cost. 9. The

16、 instruction manual gives the builder an option for higher receiver sensitivity. The consensus among kit builders appears to favor exercising this option during initial construction. I concur, as it appears easier to do at that time, rather than waiting until after the kit is finished. You be the Ju

17、dge. _ Ten-Tec Model 1253 Regenerative HF Radio Kit, Page 2 of 3. K8JHR copyright 2013 10. Some builders eschew the specified in-progress tests, but I recommend doing all of such tests as recommended in the manual. It it much easier to troubleshoot a small, isolated section of the overall circuit, t

18、han the entire circuit, if something is amiss after final construction. 11. Some builders replace the RCA phono jack (antenna jack) with a more robust BNC or UHF (PL-250=9) jack. This is easier to accomplish during initial construction, than afterward. This seems a good suggestion as either of the r

19、ecommended replacement jacks are more robust and sturdy than the supplied RCA jack, and can be expected to take more stress and abuse before failure, especially if the builder uses a stiff, heavy duty coax cable such as ham operators typically use. 12. Reserved _ Ten-Tec Model 1253 Regenerative HF Radio Kit, Page 3 of 3. K8JHR copyright 2013 Interior view of completed kit.