Superstar_4900B_troubleshooting.pdf

《Superstar_4900B_troubleshooting.pdf》由会员分享，可在线阅读，更多相关《Superstar_4900B_troubleshooting.pdf（2页珍藏版）》请在收音机爱好者资料库上搜索。

1、Transmit Section Voltage Chart: 2SC2314ReceiveTransmitTransmit RF Pre-Driver Emitter0.0 VDC0.9 VDC Collector0.0 VDC10.8 VDC Base0.0 VDC1.9 VDC 2SC2166ReceiveTransmitTransmit RF Driver Emitter0.0 VDC0.0 VDC Collector10.2 VDC11.2 VDC Base0.0 VDC1.0 VDC 2SC1969ReceiveTransmitTransmit RF Final (1 of 2)

2、Emitter0.0 VDC0.0 VDC Collector10.1 VDC10.1 VBC Base0.0 VDC1.0 VDC 2SC1969ReceiveTransmitTransmit RF Final (2 of 2) Emitter0.0 VDC0.0 VDC Collector10.1 VDC10.1 VBC Base0.0 VDC1.0 VDC 2SA1940ReceiveTransmitDC Power Regulator Emitter29.0 VDC24.8 VDC Collector10.8 VDC10.4 VDC Base28.6 VDC23.4 VDC Repai

3、r Notes: The voltages shown on the transmit buss are directly related to the variable RF output control on the front panel. This control varies the voltage from 2.5 VDC through 10.8 VDC at the collector of the 2SA1940 DC power regulator transistor. The 2SA1940 DC voltage regulator is good for about

4、55 Watts and can be directly replaced with a 2SB754 (60 Watts) if necessary. A good method of trouble shooting the transmit section is to check the voltage at the collector of the 2SC2314 pre driver first. There should be around 10.8 VDC on the collector in transmit mode. If the voltage is substanti

5、ally lower, the 2SC2314 is probably bad. Next, check the collector of the 2SA1940. This voltage should be around 10.8 VDC with the RF Power Control completely clockwise. If the voltage here is substantially low, the 2SC2166 (Driver) or one or more of the 2SC1969 (Finals) is shorted. To check this qu

6、ickly, unsolder the collector of the 2SC2166 first and check voltage again. If this doesnt bring the voltage back up, do the same thing on each 2SC1969 (Final) transistors (one at a time) to determine which transistor is bad. The 2SA1940 DC regulator transistor could be bad if the voltage doesnt ret

7、urn in the tests above. Check the emitter and base voltages to see if the rest of the power suply if functioning. By lifting the collector and checking these voltages, one can determine if the transformer and rectifiers are working properly. If the collector voltage drops to near zero after solderin

8、g it back to the board, the 2SC1940 or one of its support transistors (located in front of it) are probably shorted. Although the SuperStar 4900 circuit board is largely SMT (Surface Mount Technology) it is very easily repaired because most of the components that usually need service are standard co

9、mponents and located conveniently. * See the pictorial diagrams for component location and pin out information. SuperStar 4900B Troubleshooting Transmit Section Repair Memorandum - 12/2000 Copyright (C) 2000 by - All rights Reserved SuperStar 4900B Troubleshooting Transmit Section Repair Memorandum - 12/2000 2SC2166 E C B 2SC1969 E C B 2SC1969 E C B 2SC2314 B C E 2.5 VDC - 10.8 VDC Varies With Front Panel RF Power Control 2SA1940 Collector - Variable Voltage From RF Power Control 2SA1940 E C B Note: 2SA1940 Can be replaced with a 2SB754 Transistor Copyright (C) 2000 by - All rights Reserved