VXR1000.pdf

《VXR1000.pdf》由会员分享，可在线阅读，更多相关《VXR1000.pdf（48页珍藏版）》请在收音机爱好者资料库上搜索。

1、1 2003 VERTEX STANDARD CO., LTD. E137190A Service Manual VXR-1000 (VHF) The VXR-1000 Series is designed to provide extended handheld coverage by repeating transmissions in both directions through an existing high power mobile radio. Reliability is assured by a highly integrated surface mount circuit

2、 design and a aluminum extrusion chassis. Important channel frequency data is stored in EEPROM, and is easily programmable by dealers using a personal computer and the Vertex VPL-1 Programming Cable and CE-22 Software. Please take a few minutes to read this manual carefully. The information presente

3、d here will allow you to derive maximum performance from your VXR-1000. After reading it, keep the manual handy for quick reference, in case questions arise later on. Were glad you joined the Vertex team. Call on us any time, because our business is communications. Let us help you get your message a

4、cross. Vehicular Cross-band Repeater Contents Operating Manual Reprint. 2 Specifications . 4 Installations . 5 Interconnection with Vertex VX- Series Transceiver . 7 VXR-1000 Trunking Interface Manual.11 CE-22 Programming Software .14 Exploded View open: high-Z (4.7 k) * JP1005: Controls the maximum

5、 drive level of the transmit audio output to the mo- bile. Short: low level output (0-100 mV)*; open: high level output (0-5 V). JP1001/1002/1003: Polarity of Power supply control. De- fault setting: active high (JP1003: short). VR1001: Mobile Microphone level VR1002: Mobile RX Audio (External Modul

6、a- tion level) VR1007:Mobile TX Audio (output level) * default setting The VXR-1000 has a fixed 3 minute time-out tim- er for base to handheld transmissions. If the mobile COR is active for more than 3 minutes it will send a error blip and cease transmission until the mobile COR is inactive. FUNCTIO

7、NAL DESCRIPTION When the user leaves the vehicle, they activate their mobile radio via its front panel or a sepa- rate switch. When the mobile radio is receiving a signal, the VXR-1000 will begin transmitting on the hand-helds receive frequency. The user is able to hear and respond to all radio traf

8、fic, including other hand-helds on the same frequen- cy. The repeater jumpers and potentiometers are custom-configured for use with the particular mobile radio to which it will be connected. The CE-22 software is used to program the repeater for the required operating parameters. TRUNKING OPERATION

9、When the radio is connected to a trunking mo- bile you wish to access the system from your handheld radio, key the handheld briefly then release the PTT key. The radio will attempt to acquire a voice channel on the trunking system by keying the mobile for 200 mS and monitor- ing the “on-air detect”

10、line from the mobile. If the VXR-1000 does not see the radio transmit at all (system is busy), it will send a low tone to the handheld to alert you that the system is busy. The radio will automatically retry every 5 sec- onds and send a “busy” tone to the handheld with each unsuccessful attempt, to

11、indicate progress of the call attempt. If unsuccessful af- ter 30 seconds, the radio will transmit an “inter- cept” tone to alert the handheld that the call at- tempt failed. When the VXR-1000 detects that the mobile is transmitting, it will continue to monitor the “on- air detect” line until the tr

12、ansmitter remains keyed for at least 250 mS to determine if the ra- dio is merely handshaking or retrying. After successful acquisition of a voice channel, it will continue to hold the mobiles PTT active for 2 seconds and transmit a “go-ahead” blip to the handheld. You may then key their handheld to

13、 speak on the voice channel. If you do not key up within the 2-second period, the radio will un- key the mobile and send the “intercept” tone, as before. 4 Specifications GENERAL Frequency Range:150 - 174 MHz (Receive frequencies within a 5 MHz spread over the range 150 - 174 MHz) Number of Channels

14、:16 Channels Channel Spacing:12.5/25 kHz Supply Voltage:13.8V DC, negative ground Ambient Temperature Range:30 C to +60 C Frequency Stability:2.5 ppm RF Input-Output Impedance:50 Audio Output Impedance:8 Case Size (WHD):111 25.4 136 mm (4.4” 1” 5.4”) Weight:400 g (0.9 lb.) RECEIVER Circuit Type:Doub

15、le Conversion Superheterodyne Sensitivity:EIA 12dB SINAD 0.30 V 20 dB Quieting:0.40 V Squelch Threshold:0.2 V to 2 V Adjacent Channel Selectivity:60 dB Intermodulation Rejection:60 dB Spurious and Image Rejection:60 dB Conducted Spurious Emissions: 57 dBm Audio Output:1 W into 8 w/3 V, Squelch close

16、d: 0 V. This input level can be switched between “Squelch open” and “Squelch closed” when this pin is at “high” level via CE-22. Impedance: 1 M. The Squelch Threshold level can be changed by ad- justment of VR1003. Pin 8: Mobile Microphone Audio Mobile microphone audio input. This is the same au- di

17、o which is being sent to the mobile radios Mic Amp circuit (i.e. the microphones audio is “split” between the mobile radio and the VXR-1000) Input impedance: 100 k The input level to the mobile transceiver can be changed via CE-22 (range) and VR1001 (value). CE-22 EXT MIC level “HIGH”: 18 dBm 0 dBm

18、CE-22 EXT MIC level “LOW”: 44 dBm 18 dBm Pin 9: Mobile TX detect/Mobile Microphone PTT Mobile Tx/Rx control input. This input function can be switched between “Mobile MIC PTT” input and “Mobile Tx Detect” line input via CE-22. This input level can be switched between “Tx” and “Rx” when this pin is a

19、t “high” level via CE-22. Input impedance: 10 k. Note:, When the VXR-1000 is used in a Trunking sys- tem, the “Mobile TX Detect” input signal must be re- ceived from the mobile transceiver when connected to the Trunking system (the VXR-1000 checks this pins level to confirm successful connection to

20、the trunking system). When this pin is at “high” level (3 V), the VXR-1000 is commanded into the TRANSMIT mode. When a successful “handshake” occurs with the Trunk- ing system, this line goes “low” and the VXR-1000 is released into the RECEIVE mode. Pin 4: Mobile PTT Output This pin controls the mob

21、ile transceivers TX/RX status. This pin is an open-collector, “active-low” circuit. When this pin closes to ground, the mobile transceiver is switched into the TRANSMIT mode. Maximum current: 20 mA. Pin 5: Vcc (13.8 V) This pin is the DC power supply connection for the VXR-1000. Maximum current: 2A.

22、 Pin 6: Mobile Receive Audio Receiver audio input to the VXR-1000 from the mobile transceiver. Function VXR-1000 turns on when this pin connects to ground. VXR-1000 turns off when this pin connects to ground. VXR-1000 turns off when this pin is “high” level. VXR-1000 turn on when this pin is “high”

23、level. JP1001 short short open open J1002 short open short open J1003 open short open short 7 This document outlines the interconnections and hardware settings required for interface of the Ver- tex VXR-1000 Compact Mobile Repeater to the Vertex VX- series of mobile transceivers. 1. Interconnections

24、 to Mobile Transceivers The chart below shows the interconnections between J1004 on the VXR-1000 and the correspond- ing interface jacks on the compatible mobile transceivers. Note 1: The Mobile COR Detect line may be connected, inside the mobile trans- ceiver, to either pointshown (e.g. for the VX-

25、2000, either to Pin 1 of J1003 (SQ) or to the Base of Q1008 )AF MUTE). See Section 6 of this document for information regarding the Mobile COR Detect connection in the VX- 3000. Note 2: When the mobile transceiver is not used in a trunking environment, the “Mobile TX Detect” function is not used. VX

26、R-1000 DSUP 9-pin Accessory ConnectorVXR-1000 DSUP 9-pin Accessory ConnectorFTL-7011FTL-7011VX- 2000VX- 2000VX- 3000VX- 3000 Pin 1GNDPin 8 of J 2006GNDPin 5 of J 1003GNDPin 5 of J 1004GND Pin 2Mobile Transmit AudioPin 4 of J 2006MIC INPin 3 of J 1003MOD INPin 3 of J 1004EXM Pin 3Power Supply Control

27、Pin 12 of J 200613.8V SWEDPin 8 of J 1003+5VPin 8 of J 100413 S WD Pin 4Mobile PTT OutputPin 1 of J 2006PTTPin 7 of J 1003PTTPin 7 of J 1004PTT Pin 5Vc c (13.8 V)Pin 9 of J 200613.8VTP100313.8V13.8 V IN13.8V Pin 6Mobile Receive AudioPin 3 of J 2001DET INPin 2 of J 1003DISC OUTPin 2 of J 1004LINE Pin

28、 7Mobile COR Detec t (Note 1) Pin 1 of J 2001 (or Base of Q2005) S Q SIG (AF MUTE) Pin 1 of J 1003 (or Base of Q1008) S Q (AF MUTE) Pin 1 of J 1004S Q Pin 8Mobile Microphone AudioNo ConnectionNo ConnectionNo Connection Pin 9Mobile TX detect/Mobile Mic. PTT (Note 2)Pin 5 of J 2005RX/TXTP1013TX 9VNo C

29、onnection ShieldGNDGNDGNDGND Interconnection with Vertex VX- Series Transceivers 8 3-3: CE-22 “Common Data” (F2) Settings Use the “CE22 /P” option when starting the CE-22 Software. PTT1 State: High PTT2 State: High Pre-emphasis:Off De-Emphasis:On EXT MIC Level: Low EXT MOD Level:Low 4. VX-3000 (HARD

30、WARE/SOFTWARE SETTINGS FOR VXR-1000) 4-1: VX-3000 Internal Jumpers These jumpers configure the interconnec- tions made via the D-sub 9-pin connector on the rear of the VX-3000. Note that the connections for the VX-3000L (Low-Band) are different from those for the VX-3000U. VX-3000LJP1002Open JP1003J

31、umper JP1004Open JP1005Jumper JP1009Open JP1010Jumper VX-3000UJP1003Open (RXD) JP1004Jumper (EXRA) JP1005Open (TXD) JP1006Jumper (EXM) JP1009Open JP1010Jumper Connect a 10 k resistor between Pin 1 and Pin 8 at J1004 of the VX-3000; this is a pull- up resistor for the Squelch line. 4-2: VX-3000 Softw

32、are Settings in CE-19 for PTT and MIC These settings must be set appropriately within CE19 in order for the VXR-1000 to work correctly with the VX-3000. 2. FTL-7011 (HARDWARE/SOFTWARE SETTINGS FOR VXR-1000) 2-1: VXR-1000 Internal Jumpers POWER SUPPLY CONTROL:JP1001Open JP1002Open JP1003Jumper VXR-10

33、00 OUTPUT:JP1004Open JP1005Jumper 2-2: CE-22 “Common Data” (F2) Settings Use the “CE22 /P” option when starting the CE-22 Software. PTT1 State: High (set to “Low” if con- necting to the MUTE connection at the base of Q2005) PTT2 State: Low(if no connection is made to Pin 9 of J1004, set to “High”) P

34、re-Emphasis: Off De-Emphasis: On EXT MOD Level:Low EXT MOD Level:Low 3. VX-2000 (HARDWARE/SOFTWARE SETTINGS FOR VXR-1000) 3-1: VX-2000 Internal Jumpers These jumpers configure the interconnec- tions made via the D-sub 9-pin connector on the rear of the VX-2000. JP1002Open JP1003Jumper JP1004Jumper J

35、P1005Open 3-2: VXR-1000 Internal Jumpers POWER SUPPLY CONTROL:JP1001Open JP1002Open JP1003Jumper VXR-1000 OUTPUT:JP1004Open JP1005Jumper Interconnection with Vertex VX- Series Transceivers 9 1000) for an output deviation of 3.0 kHz (1.5 kHz in the “Narrow” mode). 5-2: VXR-1000 Receiver Output Level

36、Setting When the VXR-1000 receives a signal from an external signal source (on the uplink fre- quency used by the portable transceiver) modulated at 1 kHz at a level of 3.0 kHz (1.5 kHz in the “Narrow” mode”), the out- put passed to the connected mobile trans- ceiver should produce a transmitted out

37、put signal from the mobile at a level of 3.0 kHz (1.5 kHz in the “Narrow” mode”). If the output level to the mobile does not produce correct deviation from the mobile, adjust VR1007 (inside the VXR-1000) so that the transmitted output from the mobile is modulated at a level of 3.0 kHz (1.5 kHz in th

38、e “Narrow” mode”). 6. Trunking System configuration All trunking parameters depend on the con- figuration of the individual trunking system in which the connected mobile transceiver is used. Please consult the CE22 program- ming instructions, and the separate “VX- 1000R Trunking Interface Manual,” f

39、or in- formation about the software and other set- tings for the VXR-1000 when integrated into a trunking environment. 7. Miscellaneous In order to improve the audio muting per- formance of the VX-3000, a minor circuit change was adopted from Production Lot #03 (VX-3000L/U) and 04 (VX-3000V), and th

40、is change was reflected in CE-19 software version 1.16. This change affects the connec- tion point for the Squelch (Mobile COR De- tect) line, and the connection point is iden- tified as “AF MUTE in the various documen- tation for the VX-3000. The configuration version can be identified by looking f

41、or the presence of a jumper con- nection at jumper pad JP1002 in the VX- 3000U, or JP1016 in the VX-3000L. The con- nections for the Mobile COR Detect line should be made as follows: COMMON MISCELLANEOUS EXTERNAL PTT Set to (Mic for other Trunking systems like LTR, this parameter must be set to ON).

42、 ? Set PTT1 to HIGH. ? Other parameters such as Master/Slave and Sub_Audio may be set via CE-22 per the cus- tomers operating requirements. 13 VXR-1000 Trunking Interface Manual 5. NOTES RE TRUNKING OPERATION 5-1: The VX-Trunk II system operates in a full du- plex mode. In this environment, while a

43、call is in progress, the connected mobile passes the received au- dio through to the VXR-1000 for re-transmis- sion to the portable. In order for the portable to be able to capture the VXR-1000 to make a transmission back to the other party, the VXR-1000 must be set, via the CE-22 software, for a Pr

44、iority Timer setting (Pri Timer) which is not zero. A very short time will allow quick interruption, but the incoming message from the VXR-1000 to the portable may sound choppy due to the frequent interrupts. When the portable transmits longer than the Priority Timer setting, the VXR-1000 will in- t

45、errupt its transmission, and the VXR-1000 will instantly switch to the receive mode on the portables transmitting frequency. 5-2: VXR-1000 Local Microphone In order to facilitate the above sampling fea- ture, it is not possible to use a Local mic (a DTMF microphone attached to the VXR-1000) for acce

46、ss to the VX-Trunk II system. 14 The Vertex CE-22 program is a software package which controls the VXR-1000s Clone Edit feature. This manual outlines the installation and use of the CE-22 software when used with the VXR-1000. 1.CE-22 Installation and Operating Modes The Vertex CE-22 program is an in

47、tegrated software package designed to work with IBM PC, XT, AT, or compatible computers. In order for CE-22 to run properly, your computer must run DOS v3.0 (or a later ver- sion). 1-1: CE-22 Installation There is no installation software included with your distribution diskette. Use standard DOS pr

48、ocedures to install the software on your hard drive. For example, let us create a directory named Vertex into which we shall install the CE- 22 software. First, make a copy of the distri- bution diskette, then use the archive copy for the installation from (floppy) Drive A: c: mkdir vertex ENTER c:

49、cdvertex ENTER c:vertex copy a:*.* ENTER The files on the archive floppy disk will now be copied to your hard drive into the new vertex directory. 1-2: Starting CE-22 Before starting the CE-22 program, connect the VPL-1 Cloning Cable between your computers COM port and the VXR-1000s MIC jack. Connecting the VPL-1 cable automatically initiates the CLONE (programming) mode, and the PWR LED will blink while the CLONE