Yaesu_DMU-2000_user.pdf

《Yaesu_DMU-2000_user.pdf》由会员分享，可在线阅读，更多相关《Yaesu_DMU-2000_user.pdf（56页珍藏版）》请在收音机爱好者资料库上搜索。

1、DATA MANAGEMENT UNIT DMU-2000 OPERATING MANUAL VERTEX STANDARD CO., LTD. 4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. YAESU EUROPE B.V. P.O. Box 75525, 1118 ZN Schiphol, The Netherlands YAESU UK LTD. Unit 12, Sun Va

2、lley Business Park, Winnall Close Winchester, Hampshire, SO23 0LB, U.K. VERTEX STANDARD HK LTD. Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road, Kwun Tong, Kowloon, Hong Kong VERTEX STANDARD (AUSTRALIA) PTY., LTD. Normanby Business Park, Unit 14/45 Normanby Road Notting Hill 3168, Victoria, Aust

3、ralia Provided by? YAESU museum? ? Downloaded by? RadioAmateur.EU Installation and Connection.1 Switches and Connectors.2 Please Read This First .4 Before Using an External Monitor .6 About the DMU-2000 Data Management Operation.6 About Menu Mode Operation .8 About the Monitor Display.10 How to Use

4、the World Clock function.12 About the World Clock.12 Explanation of the Function Keys on the World Map Screen .12 SET (LOCAL-TIME1) Setup.13 FORMAT (TIME FORMAT) Setup .13 City Selection.14 Miscellaneous World Clock Setup Options .15 OFF Timer and Alarm Setup .16 Spectrum Scope.18 About the Spectrum

5、 Scope .18 Explanation of the Function Keys on the Spectrum Scope Screen .18 Using the CTR (Center) Display Mode.20 Using the LBWS (Limited Band Width Sweep) Function .22 Using the FIX (Fixed) Mode .23 Audio Scope and Oscilloscope .24 About the Audio Scope and Oscilloscope.24 Explanation of the Func

6、tion Keys on the Audio Scope and Oscilloscope Screen.24 Using the Audio Scope .25 Audio Scope Specifications.25 Using the Oscilloscope .26 Oscilloscope Specifications.26 Log Book Function.28 About the Log Book .28 Explanation of the Function Keys on the Log Book Screen .28 Log Book Example .29 CONFI

7、G Setting .30 CONFIG SETTING Mode Setup.31 Log Book Data Input.32 Log Book Previous-QSO Check (CHECK).33 Editing Log Book Entries.33 Saving Log Data .34 Loading Log Data (LOAD).34 Summary Check.35 Temperature / SWR Indication .36 About the Temperature / SWR Indication .36 Explanation of the Function

8、 Keys on the Temperature / SWR Indication Screen .36 Graphic Meter Displays .37 Swept SWR Display.38 Using the Marker on the SWR Graph .39 Great Circle Map / Rotator Control Function .40 About the Great Circle Map / Rotator Control Function Screen .40 Explanation of the Function Keys on the Great Ci

9、rcle Map / Rotator Control Function Screen.40 Manual Mode.42 Preset Mode .43 Memory Mode.44 Using the Memory Channel List .45 About the Memory Channel List.45 Explanation of the Function Keys on the Memory Channel List Screen .45 Erasing a Memory Channel/Restoring an Erased Memory Channel .46 Saving

10、 Memory Data .46 Loading Memory Data.47 Using the MENU Mode .48 About the MENU Mode .48 Explanation of the Function Keys on the Menu Mode Screen.49 Memu Mode Configuration Changes .50 Menu Mode Reset.50 Saving Menu Configuration Data .51 Loading Menu Data.52 TABLE OF CONTENTS DMU-2000 DATA MANAGEMEN

11、T UNITPage 1 DMU TRX KEYBOARD Supplied Connection Cable MONITOR AC IN AC IN Antenna INSTALLATION AND CONNECTION 1. Make certain that all cables are disconnected from the transceiver. 2. Referring to Figure 1, remove the three screws from each side of the transceiver, and three screws from the top ed

12、ge of the rear panel. Slide the top cover to- ward to the rear about 1/2 inch (1 cm), then remove the top cover. 3. Refer to Figure 2 for the mounting location for the SCOPE Unit. Locate the 14-pin plug taped on the chas- sis. Remove the tape and remove the 14-pin plug from the chassis. 4. Mount the

13、 SCOPE Unit using the supplied four screws (Figure 3). 5. Referring to Figure 4, plug the 14-pin plug which was removed from the chassis in the previous step into the J7002 connector on the SCOPE Unit. 6. Locate the Coaxial plugs (labeled and ) installed in jacks (J4508 and J4507) on the RX-2 Unit.

14、Un- plug the Coaxial plug () from the RX-2 Unit and plug it into the J7003 on the SCOPE Unit. Unplug the Coaxial plug () from the RX-2 Unit and plug it into the J7001 on the SCOPE Unit (Figure 4). 7. Replace the top cover and its nine screws. 8. Assemble the transceiver, Data Management Unit, after-

15、market Display, and after-market Keyboard (if used) pursuant to Figure 5. Figure 1 Figure 2 Figure 3 SCOPE Unit Mounting Location 14-pin Plug Figure 4 14-pin Plug SCOPE Unit RX-2 Unit Figure 5 Move the Coaxial plug Move the Coaxial plug Keep a inch (2.5 cm) of space on ei- ther side of the DMU-2000

16、to pre- vent the overheating. DMU-2000 DATA MANAGEMENT UNITPage 2 POWER Switch Press this switch to turn the Data Management Unit on, after first setting the rear panel POWER switch to the “I” position. Press this switch again to turn the Data Management Unit off. If the rear panels POWER switch is

17、set to the “O” position, the front panel POWER switch will not function. CF Card Slot This slot accepts the supplied Compact Flash (CF) Card, which allows storage, transfer, and recall of transceiver configuration data and operator prefer- ences, along with Log Book data, etc. When the CF Card is su

18、ccessfully inserted, the red LED by the slot will light up. To remove the card out from slot, press the small push- button at the right hand side of the slot. Advice: If you get the “CF CARD IS NOT READY” error message on the after-market monitor, check the position of the CF Card in the slot for pr

19、oper align- ment. Main POWER Switch This is main power On (I)/Off (O) switch of the Data Management Unit. Always turn this switch on before turning on the front panels POWER button. If this switch is not turned On, the front panel POWER switch will not function. FUSE This holder requires a 3.15-A fu

20、se. Always use the 3.15 Amp fuse, whether operating on 100 - 120 VAC or 200 - 240 VAC. AC IN Jack Connect the supplied 3-wire AC line cord to this socket after ensuring that your AC mains voltage matches that on the label. See the Installation section for instructions on how to change the internal s

21、witch- ing power supply AC mains voltage, if necessary. TRX Jack Connect this 8-pin MINI-DIN jack to the DMU jack on the FT-2000 transceiver, using the supplied con- trol cable. COM Jack Connect a after-market GPS re- ceiver capable of supplying NMEA data to this jack. The data line connects to Pin

22、2, and the ground shield connects to Pin 5. When you connect the GPS receiver to this jack, the “Rotator” page on the after-market monitor will au- tomatically include a Great Circle map centered on your location. The DMU-2000 can support the GGA, GLL, and RMC Data Sentences from the GPS re- ceiver. KEY BOARD Jack Connect your keyboard (not supplied) to one of these jacks in accordance with your keyboard type (“USB” or “PS/2”) to use the Smart Memory Card for storage of logbook data, and for input of your location when setting up the World Clock. AUDIO OUT Jack This ja