EIP_451_Service 电路图.pdf

《EIP_451_Service 电路图.pdf》由会员分享，可在线阅读，更多相关《EIP_451_Service 电路图.pdf（138页珍藏版）》请在收音机爱好者资料库上搜索。

1、TM 11-6625-3031-14 . TECHNICAL MANUAL OPERATORS, ORGANIZATIONAL, DIRECT SUPPORT, AND GENERAL SUPPORT MAINTENANCE MANUAL COUNTER, PULSE, ELECTRONIC TD-1338(V)1/USM (NSN 6625-01-120-7832) HEADQUARTERS, DEPARTMENT OF THE ARMY 6 MAY 1983 RadioFans.CN 收音机爱 好者资料库 SAFETY STEPS TO FOLLOW IF SOMEONE IS THE V

2、ICTIM OF ELECTRICAL SHOCK DO NOT TRY TO PULL OR GRAB THE INDI- VIDUAL IF POSSIBLE, TURN OFF THE ELECTRICAL POWER IF YOU CANNOT TURN OFF THE ELECTRICAL POWER, PULL, PUSH, OR LIFT THE PERSON TO SAFETY USING A WOODEN POLE OR A ROPE OR SOME OTHER INSULATING MATERIAL SEND FOR HELP AS SOON AS POSSIBLE AFT

3、ER THE INJURED PERSON IS FREE OF CON- TACT WITH THE SOURCE OF ELECTRICAL SHOCK, MOVE THE PERSON A SHORT DISTANCE AWAY AND IMMEDIATELY START ARTIFICIAL RESUSCITATION RadioFans.CN 收音机爱 好者资料库 TECHNICAL MANUAL NO. 11-6625-3031-14 TM 11-6625-3031-14 HEADQUARTERS DEPARTMENT OF THE ARMY WASHINGTON, D.C. 6

4、May 1983 ORGANIZATIONAL, DIRECT SUPPORTOPERATORS, AND GENERAL SUPPORT MAINTENANCE MANUAL FOR COUNTER, PULSE, ELECTRONIC TD-1338(V)1/USM (NSN 6625-01-120-7832) REPORTING ERRORS AND RECOMMENDING IMPROVEMENTS You can help improve this manual.If you find any mistakes or if you know of a way to improve t

5、he procedures, please let us know. Mail your letter,DA Form 2028 (Recommended Changes to Publica- tions and Blank Forms),or DA Form 2028-2 located in the back of this manual direct to:Commander, US Army Communications- Electronics Command and Fort Monmouth, ATTN:DRSEL-ME-MP, Fort Monmouth, NJ 07703.

6、 In either case, a reply will be furnished direct to you. Chapter1. Section I. II. III. TABLE OF CONTENTS Para INTRODUCTION General Information . . . . . . . . . . . . . . . Scope. . . . . . . . . . . . . . . . . . . . 1-1 Reports of maintenance forms, records and reports. . . . . . . . . . . . . .

7、. . . . . . . 1-2 Administrative storage . . . . . . . . . . . . . 1-3 Destruction of Army electronics materiel. . . . . 1-4 Reporting equipment improvement recommendations (EIRS). . . . . . . . . . . . . . . . . . . . . 1-5 Warranty information . . . . . . . . . . . . . . 1-6 Equipment Description

8、. . . . . . . . . . . . . . Equipment characteristics, capabilities and features . . . . . . . . . . . . . . . . . . . . 1-7 Equipment data . . . . . . . . . . . . . . . . . 1-8 Technical Principles of Operation . . . . . . . . Counter functional operation . . . . . . . . . . 1-9 Page 1-1 1-1 1-1 1-

9、1 1-1 1-1 1-1 1-2 1-2 1-2 1-4 1-4 i RadioFans.CN 收音机爱 好者资料库 TM 11-6625-3031-14 TABLE OF CONTENTS - Continued Para Basic counter A1 . . . . . . . . . . . . . .1-10 Converter A2 . . . . . . . . . . . . . . . . . . 1-11 Chapter2.OPERATING INSTRUCTIONS Section I.Description and Use of Operators Controls

10、 and Indicators . . . . . . . . . . . . . . . . . . . Front-panel controls, connectors and indicators . . . . . . . . . . . . . . . . . . . Rear-panel controls and connectors. . . . . . . . II.Preventive Maintenance Checks and Services . . . General instructions. . . . . . . . . . . . . . . PMCS pro

11、cedures. . . . . . . . . . . . . . . . . Cleaning instructions . . . . . . . . . . . . . . III.Operation Under Usual Conditions . . . . . . . . Assembly and preparation for use . . . . . . . . Operation as stand-alone instrument . . . . . . . Externally enabled operation . . . . . . . . . . Pulse pr

12、ofile measurements. . . . . . . . . . . . Dynamic characteristics of time varying signals . Multiple pulse signal measurements . . . . . . . Timing considerations . . . . . . . . . . . . . . Accuracy . . . . . . . . . . . . . . . . . . . . Techniques for improving accuracy . . . . . . . . Operation

13、using General Purpose Interface Bus . . Chapter3.OPERATOR AND ORGANIZATIONAL Section I. Lubrication . . . . . . . . . . . . . . II.Troubleshooting Procedures . . . . . . . . . . III.Maintenance Procedures . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . . . . . In

14、spection. . . . . . . . . . . . . . . . . . . . . . . . Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . Replacement . . . . . . . . . . . . . . . . . . . . . . . Test. . . . . . . . . . . . . . . . . . . . . . . . . MAINTENANCE 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 2-10 2-11 2-12 2-13 2-14

15、2-15 3-4 3-5 3-6 3-7 3-8 Chapter4.DIRECT SUPPORT AND GENERAL SUPPORT MAINTENANCE Section I.Repair Parts, Special Tools; Test Measurement, and Diagnostic Equipment (TMDE); and Support Equipment. . . . . . . . . . . . . . . . . . . . . . . . . Common tools and equipment . . . . . . . . . . Special too

16、ls, TMDE,and support equipment . . Repair parts . . . . . . . . . . . . . . . . . . . . . . II.Service Upon Receipt . . . . . . . . . . . . . III.Troubleshooting . . . . . . . . . . . . . . . . . . . . . Introduction . . . . . . . . . . . . . . . . . . . Reference diagrams . . . . . . . . . . . . .

17、. IV.Maintenance Procedures . . . . . . . . . . . . Disassembly, replacement, and reassembly . . . Adjustments. . . . . . . . . . . . . . . . . . Performance test . . . . . . . . . . . . . . . . . 4-1 4-2 4-3 4-5 4-6 4-7 4-8 4-9 Page 1-6 1-8 2-1 2-1 2-1 2-5 2-5 2-5 2-6 2-7 2-7 2-8 2-10 2-10 2-11 2-1

18、1 2-11 2-12 2-13 2-13 3-1 3-1 3-3 3-3 3-3 3-3 3-3 3-3 4-1 4-1 4-1 4-1 4-1 4-1 4-1 4-2 4-17 4-17 4-20 4-28 ii TM 11-6625-3031-14 TABLE OF CONTENTS - Continued Para SectionV.Preparation for Storage or Shipment . . . . . . . Preparation of equipment. . . . . . . . . . . . . 4-10 Packing instructions. .

19、 . . . . . . . . . . . . . 4-11 Appendix A. REFERENCES. . . . . . . . . . . . . . . . . . . . Appendix B.MAINTENANCE ALLOCATION . . . . . . . . . . . . . Appendix C.COMPONENTS OF END ITEM AND BASIC ISSUE ITEMS LISTS. . . . . . . . . . . . . . . . . . . Appendix D.ADDITIONAL AUTHORIZATION LIST . . .

20、. . . . . . . Appendix E.EXPENDABLE SUPPLIES AND MATERIALS LIST . . . . . Page 4-33 4-33 4-33 A-1 B-1 C-1 D-1 E-1 iii TM 11-6625-3031-14 LlST OF ILLUSTRATIONS Figure 1-1 1-2 1-3 1-4 2-1 2-2 2-3 2-4 2-5 2-6 2-7 2-8 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 FO-1 FO-2 FO-3A FO-3B FO-4A FO-4B F

21、O-5A FO-5B FO-6A FO-6B FO-7A FO-7B FO-8A FO-8B FO-9A FO-9B FO-10A FO-10B TitlePage Counter,Pulse, Electronic TD-1338(V)1/USM . . . . . . . . . . . . 1-0 Counter,Functional Block Diagram. . . . . . . . . . . . . . . . . 1-5 Basic Counter A1,Functional Block Diagram . . . . . . . . . . . . 1-7 Convert

22、er A2, Functional Block Diagram . . . . . . . . . . . . . . 1-9 Counter Front Panel. . . . . . . . . . . . . . . . . . . . . . . .2-1 Counter Rear Panel. . . . . . . . . . . . . . . . . . . . . . . .2-4 Pulse Profile Measurement Test Setup . . . . . . . . . . . . . . . 2-10 Pulse Profile Measurement

23、 . . . . . . . . . . . . . . . . . . . . 2-10 Time Varying Signal Measurement Test Setup . . . . . . . . . . . . 2-11 Internal Timing Delays . . . . . . . . . . . . . . . . . . . . . . 2-12 GPIB Capabilities and Structure . . . . . . . . . . . . . . . . . 2-15 GPIB IEEE STD 488/1975 ADDRESS SWITCH P

24、ositions . . . . . . . . . 2-16 Subassembly and Cable Locations . . . . . . . . . . . . . . . . . 4-3 Counter Interconnect A100, Connector and Switch Locations . . . . 4-17 Counter, Partial Exploded View . . . . . . . . . . . . . . . . . . 4-18 Adjustment Locations. . . . . . . . . . . . . . . . . .

25、 . . . . . 4-21 Pulse Generator Output . . . . . . . . . . . . . . . . . . . . . . 4-23 YIG Control A202, Adjustment and Test Point Locations . . . . . . 4-24 Detected Modulation and 20 kHz Reference Pulse Timing . . . . . . 4-24 Converter Sequencer A203, Adjustment and Test Point Locations. . . . .

26、 . . . . . . . . . . . . . . . . . . . . . . . .4-26 Return Loss Measurement Setup . . . . . . . . . . . . . . . . . . 4-26 Return Loss Measurement Waveform . . . . . . . . . . . . . . . . . 4-27 Typical Attenuator Control Ramp Offset . . . . . . . . . . . . . . 4-27 Comb Line . . . . . . . . . . .

27、. . . . . . . . . . . . . . . . .4-27 Counter Interconnection Schematic Diagram Interconnection Diagram,Detailed Technical Schematic Component Locator Counter Interconnect (A100) Schematic Diagram Counter Interconnect (A100) Component Locator and Descriptive Information Count Chain Control (A102) Sc

28、hematic Diagram Count Chain Control (A102) Component Locator and Descriptive Information Count Chain (A103) Schematic Diagram Count Chain (A103) Component Locator and Descriptive Information Control (A104) Schematic Diagram Control (A104) Component Locator and Descriptive Information Gate Generator

29、(A105) Schematic Diagram Gate Generator (A105) Component Locator and Descriptive Information High Frequency (A106) Schematic Diagram High Frequency (A106) Component Locator and Descriptive Information Power Supply (A107) Schematic Diagram Power Supply (A107) Component Locator and Descriptive Informa

30、tion Reference Oscillator Buffer (A108) Schematic Diagram Reference Oscillator Buffer (A108) iv TM 11-6625-3031-14 LIST OF ILLUSTRATIONS (Continued) Figure Title FO-11A FO-11B FO-12A FO-12B FO-13A FO-13B FO-14A FO-14B FO-15A FO-15B FO-16A FO-16B Component Locator and Descriptive Information Display

31、(A110) Schematic Diagram Display (A110) Component Locator Converter Interconnect (A200) Schematic Diagram Converter Interconnect (A200) Component Locator and Descriptive Information Source/Amplifier (A201) Schematic Diagram Source/Amplifier (A201) Component Locator and Descriptive Information Yig Co

32、ntrol (A202) Schematic Diagram Yig Control (A202) Component Locator and Descriptive Information Converter Sequencer (A203) Schematic Diagram Converter Sequencer (A203) Component Locator and Descriptive Information IF Processor (A204) Schematic Diagram IF Processor (A204) LIST OF TABLES Table 1-1 2-1

33、 2-2 2-3 2-4 2-5 2-6 2-7 2-8 2-9 3-1 4-1 4-2 4-3 4-4 4-5 4-6 4-7 TitlePage Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . Front-panel Controls, Connectors and Indicators . . . . . . . . . Rear-panel Controls and Connectors . . . . . . . . . . . . . . . . Operator Preventive Mainte

34、nance Checks and Services . . . . . . . Counter GPIB Capability Identification Codes . . . . . . . . . . . GPIB IEEE STD 488/1975 Connector Pin Assignments . . . . . . . . . On Line and Off Line ADDRESS SWITCH Settings . . . . . . . . . . . ADDRESS SWITCH Settings vs ASCII Characters . . . . . . . .

35、 . . . Programming Summary. . . . . . . . . . . . . . . . . . . . . . . . Typical Program Using Hewlett-Packard 9815 Calculator as Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . Operator and Organizational Troubleshooting . . . . . . . . . . . Symptom Index . . . . . . . . . . . .

36、 . . . . . . . . . . . . . . Direct Support and General Support Troubleshooting . . . . . . . . Power Supply Voltages and Adjustments . . . . . . . . . . . . . . Band B Response Tests . . . . . . . . . . . . . . . . . . . . . . Preset Frequency Tests . . . . . . . . . . . . . . . . . . . . . . Contr

37、ol Sequence. . . . . . . . . . . . . . . . . , . . . . . , . Converter Sequence Functions . . . . . . . . . . . . . . . . . . . 1-1 2-1 2-5 2-6 2-14 2-16 2-17 2-18 2-20 2-26 3-1 4-2 4-4 4-22 4-29 4-31 4-45 4-65 v TM 11-6625-3031-14 Figure 1-1.Counter, Pulse, Electronic TD-1338(V)1/USM 1-0 TM 11-6625

38、-3031-14 CHAPTER 1 INTRODUCTION 1-1.Scope. Section I. GENERAL INFORMATION a. This technical manual covers opera- tion and maintenance of Counter, Pulse, Electronic TD-1338(V)1/USM. Throughout this manual it is referred to as the counter. b. The counter (fig. 1-1) is used to measure the frequency of

39、cw, pulse- modulated, or frequency-modulated microwave signals between 300 MHz and 18 GHz.Pulse widths can be as narrow as 100 nanoseconds, with a maximum pulse repetition frequency of 2.5 MHz. Peak-to-peak deviation of FM signals may be as great as 40 MHz at 10 MHz modulation rates. 1-2.Reports of

40、Maintenance Forms, Records and Reports. a. Reports of Maintenance and Unsatisfactory Equipment.Department of the Army forms and procedures used for equipment maintenance will be those prescribed by TM 38-750, The Army Maintenance Management System (Army) .Air Force personnel will use AFM 66-1 for ma

41、intenance reporting and TO 00-35D54 for unsatisfactory equip- ment reporting. b. Report of Packaging and Handling Deficiencies.Fill out and forward SF 364 (Report of Discrepancy (ROD) as prescribed in AR 735-11-2/DLAR 4140.55/ NAVMATINST 4355.73/AFR 400-54/MCO 4430.3E. c. Discrepancy in Shipment Rec

42、ord (DISREP) (SF 361).Fill out and forward Discrepancy in Shipment Report (DISREP) (SF 361) as prescribed in AR 55-38/ NAVSUPINST 4610.33B/AFR 75-18/MCO P4610.19C/DLAR 4500.15. 1-3.Administrative Storage. Administrative storage of equipment issued to and used by Army activities will have preventive

43、maintenance per- formed in accordance with the PMCS charts before storing.When removing the equipment from administrative storage, the PMCS should be performed to assure operational readiness. 1-4.Destruction of Army Electronics Materiel. Destruction of Army electronics materiel to prevent enemy use

44、 shall be in accordance with TM 750-244-2. 1-5.Reporting Equipment Improvement Recommendations (EIRs). If your counter needs improvement, let us know.Send us an EIR. You, the user,are the only one who can tell us what you dont like about your equip- ment.Let us know why you dont like the design or p

45、erformance.Put it on an SF 368 (Quality Deficiency Report). Mail it to:Commander, US Army Communications-Electronics Command and Fort Monmouth, ATTN: DRSEL-ME-MP, Fort Monmouth, New Jersey 07703. Well send you a reply. 1-6.Warranty Information. The counter is warranted by EIP Microwave, Inc. for 12

46、months. It starts on the date, found in block 23, DA Form 2408-9, in the logbook.Report all defects in material or workmanship to your supervisor, who will take appro- priate action through your organiza- tional maintenance shop. 1-1 TM 11-6625-3031-14 Section II. EQUIPMENT DESCRIPTION 1-7.Equipment

47、 Characteristics, Capa- bilities and Features. The counter is a portable test instrument usable as either self- contained frequency measurement or monitoring indicator, or as part of a programmable automatic test equipment (ATE) system.It provides a direct readout of frequency from 300 MHZ through 1

48、8 MHz.Capabilities and features include: a. Measures pulse-modulated microwave signals. b. Measures frequency-modulated microwave signals. c. Measures cw microwave signals. d. Front panel self-test of digital display. e. Front panel self-test of internal circuits. f. Automatic and selectable resolut

49、ion ofreadout display. g. Overload protection built in at input connector. h. Simple change to cover different power line voltages. i. Front-panel selection of frequency scanning limits. j. Comparable with IEEE STD 488 General Purpose Interface Bus (GPIB). 1-8.Equipment Data. Table 1-1 lists the electrical and physical characteristics of the counter. Table 1-1.Specifications Frequency Range: Band A Band B Pulse Characteristics: Pulse width Pulse repetition frequency Accuracy: CW or pulse 100 sec Pulse 100 sec Averaging Error (kHz rms): 300 MHz to 950 MHz 925 MHz to 18 GHz 100 ns