BK Precision_1697_manua 电路图.pdf

《BK Precision_1697_manua 电路图.pdf》由会员分享，可在线阅读，更多相关《BK Precision_1697_manua 电路图.pdf（39页珍藏版）》请在收音机爱好者资料库上搜索。

1、RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RadioFans.CN 收音机爱 好者资料库 RECALL RECALL 714-921-9095 714-921-6422 Command Sets BK models 1696/1697/1698August 2004 BLUE Input Command RED Return Data from Power SupplyPS= Power Supply Command CodeDescription SESS OK CR Disable front panel keypad and make

2、 PSto Remote Mode ENDS OK CR Enable front panel keypad and make PSto exit Remote Mode CCOM 000-255 OK CR Change RS-232/RS485 = 0 - RS-232 = 1 - RS-485 GCOM RS RS485 Address # CR OK CR Get the RS-485 address GMAX Voltage ? Current ? CR OK CR Get maximum voltage and current of PS GOVP Voltage ? CR OK

3、CR Get Upper Voltage Limit of PS GETD Voltage ? Current ? 0 CR OK CR Voltage ? Current ? 1 CR OK CR Get Voltage & Current readingfrom PS PSin CV mode PSin CC mode GETS Voltage ? Current ? CR OK CR Get Voltage & Current Set Value from PS GETM Memory 1 Voltage ? Current ? CR Memory 2 Voltage ? Current

4、 ? CR . . . Memory 9 Voltage ? Current ? CR OK CR Get All Preset Memory Values from PS GETM location 1-9 Voltage ? Current ? CR OK CR Get Memory from Specific Preset of PS GETP Program 00 Voltage ? Current ? Minute ? Second ? CR Program 01 Voltage ? Current ? Minute ? Second ? CR . . . Program 19 Vo

5、ltage ? Current ? Minute ? Second ? CR OK CR Get all the Timed Program Memory of PS GETP program 00-19 Voltage ? Current ? Minute ? Second ? CR OK CR To Get Anyone Timed Program Memory from 20 Steps Program of PS GPAL CR Readingvoltage # VON Readingcurrent # A ON Readingwatt # W ON Timer minute # se

6、cond # timer ON colon ON m ON s ON Settingvoltage # V-const ON V-bar ON VON Settingcurrent # I-Const ON I-bar ON A ON Program # Program ON P-bar ON SETTING ON Key lock ON Key open ON FAULT ON Output on ON Output off ON Remote ON CR OK CR Get LCD Display Information VOLT voltage 010-XXX OK CR Set Vol

7、tage Level XXX-Max. Output Rating Voltage = XX.X V Current = X.XX V CURR current 001-XXX OK CR Set Current Level SOVP voltage 010-XXX OK CR Set Upper Voltage Limit of PS SOUT 0 OK CR Disable Output of PS SOUT 1 OK CR Enable Output ofPS PROM location 1-9 Voltage 010-XXX Current 001- XXX OK CR Set Vol

8、tage and Current values of Preset Memory PROP location 00-19 Voltage 010-XXX Current 001- XXXMinute 00-99 Second 00-59 OK CR Set Voltage, Current and Time period of Timed Program RUNM location 1-9 OK CR Recall Preset Memory 1-9 RUNP times 0000-9999 OK CR Run Timed Program (0000 = run infinite times)

9、 STOP OK CR Stop Timed Program NOTES: - command data, - return data, OK = OK, CR= 0dh ? = 30h, 30h, 30h, 30h - 39h, 39h, 39h, 39h (4 bytes data) ? = 30h, 30h, 30h - 39h, 39h, 39h (3 bytes data) ? = 30h, 30h 39h, 39h (2 bytes data) # = 30h, 30h, 30h, 30h 3Fh, 3Fh, 3Fh, 3Fh (4 bytes data) # = 30h, 30h, 30h 3Fh, 3Fh, 3Fh (3 bytes data) # = 30h, 30h 3Fh, 3Fh (2 bytes data) # = 30h 3Fh (1 byte data) 30h, 30h - 3fh, 3fh (2 bytes data)